Zwilling ENFINIGY 53100-300 User manual

53100-300 | 1016107
ZWILLING®ENFINIGY
Operating instructions 2

EN
2
Safety
Safety
Read these operating instructions in their
entirety and with care before using the
blender. Keep these operating instructions
in a safe place. If you transfer the blender
to a third party, ensure that you include the
operating instructions in such a transfer.
Non-observance of these operating instruc-
tions can lead to serious injury or damage
to the appliance. Zwilling does not accept
any liability for damage caused by non-ob-
servance of these operating instructions.
Important information for your safety is
specifically marked. Make sure to observe
this information in order to avoid accidents
and damage to the appliance:
Safety information
The blender (hereinafter referred to as
the “appliance”) is intended exclusive-
ly for crushing and mixing ingredients
for beverages, liquid foods (dips,
soups, sauces, pesto, ice cream) and
ice cubes. It may only be used with
the accessories supplied or approved
by Zwilling.
Any other use is considered improper
and may result in personal injury or
property damage.
Do not put any hot fats, oils, or objects
in the appliance.
The appliance is intended for domes-
tic use. It is not intended for commer-
cial use.
Certain persons are at greater risk:
This appliance may be used by chil-
dren 8 years of age and older and
by persons with reduced physical,
sensory or mental capacity or with a
lack of experience and knowledge, if
such children and persons are super-
vised or have been instructed in the
safe use of the appliance and under-
stand the hazards resulting from using
the appliance.
Children are not allowed to play with
the appliance. Cleaning and main-
tenance must not be carried out by
children without supervision.
Keep the appliance and its power
cord in an a location that is not acces-
sible to children under 8 years old.
Keep children away from the packag-
ing material. It poses a risk of suffoca-
tion.
The appliance is operated with
electric current. There is therefore a
danger of electric shock:
Only plug the appliance into a cor-
rectly installed socket.
Only operate the appliance if the
voltage stated on the rating plate
matches the voltage of your socket.
Make sure that the power cord is not
kinked or pinched and make sure that
the power cord and the appliance do
not come in contact with sources of

EN
3www.zwilling.com/ca
Safety
heat (e.g. hobs, gas flames).
When unplugging the power plug
from the socket, always unplug the
power plug directly. Do not carry the
appliance by the power cord.
Never touch the power plug with wet
hands.
Do not insert any objects into the
openings on the appliance.
As long as the power plug is plugged
in, there is a voltage inside the ap-
pliance, even if the appliance is
switched off.
After every use and in the event of
danger or a defect, unplug the power
plug from the socket immediately.
For this reason, keep the socket into
which the appliance’s power plug is
plugged easily accessible at all times.
Unplug the appliance from the socket
prior to cleaning or maintenance.
Never unscrew the appliance and do
not make any technical modifications.
The sharp and rotating blade poses a
serious risk of injury:
In the absence of supervision, discon-
nect the power plug prior to assem-
bly, disassembly and cleaning.
Be very careful when filling, emptying
and cleaning the blender bowl, and
do not reach into the blades.
Poor hygiene is a health hazard:
Do not leave any food in the blender
bowl if you are not using the appli-
ance.
Clean the appliance and all acces-
sories thoroughly prior to first use and
immediately after every use.
A faulty appliance can cause dam-
age and injuries:
Check the appliance for damage
prior to each use. If you detect any
transport damage, contact the deal-
er from whom you purchased the
appliance immediately. Never use a
faulty appliance or faulty accessories.
Never operate an appliance or ac-
cessories that have been dropped.
The appliance needs to be repaired
in the event of a fault or a damaged
power cord. The appliance does not
contain any parts that you are able to
repair yourself.
Damage may occur if the appliance
is handled incorrectly.
Place the appliance on a dry, level
and non-slip surface.
Do not place the appliance on a
hot surface or in the vicinity of strong
sources of heat.
Do not let the power cord hang
down.
When preparing food and drinks, liq-
uid may spray or flow out and cause
injury or property damage:
Always place the blender bowl on a
level, non-slip surface.
Never overfill the blender bowl.
Do not open the lid closure during
operation.
Never use the blender bowl to heat
up food or drink in the microwave.

EN
4
Safety / Technical data
Explanation of symbols
Danger of death due to electric shock
Danger of cuts at the blades
Danger of scalding from hot liquids
Risk of property damage and damage to the appli-
ance
Technical data
Power supply 220 – 240 V∼, 50–60 Hz
Energy consumption/Power 1200 W
Capacity of the blender bowl 1.8 l
Length of the power cord 1 m
Battery for the tamper Lithium battery CR2032
Dimensions of the blender
base with bowl (L x W x H) 194 x 214 x 426 mm
Weight approx. 5.6 kg
Markings
Do not dispose of in household
waste.
The appliance complies with the
directives for CE marking.

EN
5www.zwilling.com/ca
Program functions
Program functions
1
3
2
10
9
8
7
6
5
4
1On/Off 6Ice cube crushing – Chopping ice cubes
into ice pieces
2Multi-function (pulse) – Post-mixing or
pre-mixing of mixed products or indi-
vidual ingredients
7Ice –Creamy ice cream dish composed
of frozen fruit, yoghurt, ice cream
3Variable speed – Mixture with desired
consistency from lumpy to liquid
8Cocktails – Liquid mixed drink com-
posed of spirits, juices, syrup
4Cleaning – Cleaning of the blender
bowl with water and detergent
9Smoothie – Creamy mixed drink made
from fruits, herbs and dairy products
5Soup – Liquid mixture composed of
vegetables, meat, fish, broth, spices,
herbs
10 Scales – Weighing of ingredients in the
blender bowl

EN
6
Overview
2
1
4
3
5
7
6
8
10
9
1Lid closure 6Power cord
2Blender lid 7Blender base
3Display 8Blender bowl with blade
4Program symbols 9Tamper with temperature display
5Selector switch / power button 10 Scales
Overview

EN
7www.zwilling.com/ca
Operation
Operation
1
Putting the blender into operation
Prior to commissioning, you must unwind the power cord completely. You need to press
the power button to switch the blender on and off.
2.
1. 3.
2
Filling with ingredients
To fill with ingredients, you need to place the blender bowl on a flat surface and remove
the lid or unscrew the lid closure. A measuring scale for the filling quantity is attached to
the blender bowl.
1.
2.
Observe the maximum mark. Do not over-
fill. For hot ingredients, observe a maximum
filling quantity of 1,200 ml.

8
ENOperation
4
Preparing a beverage or liquid food using the automatic program
To prepare the desired mixed drink or liquid food, turn the selector switch to the left to
the corresponding program symbol and then press the power button. The preparation
duration is shown in the display. The mixing process is complete when the time in the
display has counted down and a beep sounds.
1.
2.
3
Putting the blender bowl on the base
Before you put on the blender bowl, you must first seal the bowl with the lid and the lid
closure and then place the bowl on the base so that the handle of the bowl faces the
front right.
1.
2.
The blender lid and the bowl
can only be attached as
shown.

9www.zwilling.com/ca
EN Operation
6
Using the multi-function program
To prepare any mixed drinks and liquid foods, turn the selector switch to the right to the
“Multi-function” program symbol and press and hold the power button until the desired
consistency of the product is achieved. The mixing time that has elapsed is shown in the
display. The mixing process stops if you let go of the power button.
1.
2.
5
Interrupting the automatic program
You need to press the power button to stop the mixing process. A beep sounds. You can
continue the mixing process by pressing the power button again if the desired consisten-
cy has not yet been achieved.
If the mixing process has been interrupt-
ed, you can also remove the blender
bowl from the base to refill ingredients,
press down with the tamper or check the
consistency.

10
ENOperation
8
Switching off
To switch off the blender, turn the selector switch back to the on/off position and press
the power button.
1.
2.
7
Preparing products at your own mixing speed
To select a mixing speed, turn the selector switch to the right until the blender starts up
and reaches the desired speed. Once the desired consistency of the product has been
achieved, turn the selector switch back to the on/off position.
2.1.
The selected mixing
speed is shown on the
display and by means
of six dots.

11www.zwilling.com/ca
EN
9
Weighing the contents of the blender bowl
To weigh the contents of the blender bowl, you need to turn the selector switch to the
left to the scales program symbol. The weight of the ingredients that have been filled
is shown on the display. To weigh further ingredients, you can press the power button
again and weigh the ingredients that have been added individually (tare function).
1.
2.
Operation
Instead of the blender
bowl, you can also
place the scales on
the blender base for
weighing.
If you hold down the power button,
you can change the display from
grams to ounces.

12
ENMaintenance
1
Cleaning the blender bowl
To clean the blender bowl, fill the bowl with 500 ml of water, add some detergent and
start the cleaning program. Then rinse out the blender bowl under running water.
2.
1.
3. 4. 5.
Maintenance
2
Cleaning the blender lid and scales
You can clean the blender lid and the scales under running water, with a damp, lint-free
cloth or in the dishwasher.
Clean the blades carefully.
Do not reach into them.
It is best to clean the blend-
er lid and the lid closure
separately.

13www.zwilling.com/ca
EN
3
Cleaning the blender base and tamper
You can clean the blender base and the tamper with a damp, lint-free cloth.
Maintenance / Changing the battery
Changing the battery
The tamper contains a battery. To change the battery, you need to unscrew the battery
cover, remove the electronics and replace the old battery.
1.
2. 3.
Prior to cleaning, unplug
the power plug.
The battery must be insert-
ed correctly: the top (+)
faces outwards.

14
EN
Problem Possible cause Remedy
The mixed product contains
many ingredient pieces.
The power button was not
pressed and held for long
enough in the multi-function
program.
Press and hold the power but-
ton until the desired consisten-
cy is reached.
The mixing speed is too low
or the mixing duration too
short if you have selected
the mixing speed yourself.
If you have selected the mix-
ing speed yourself, turn the
selector switch further to the
right to increase the mixing
speed, or extend the mixing
process until the desired con-
sistency is reached.
The ingredients are not
suitable for the selected
automatic program to be
used.
Finish mixing the mixed
product with the multi-func-
tion program until the desired
consistency is achieved.
The appliance switches off
immediately.
The power button was not
pressed and held in the
multi-function program.
Press and hold the power
button.
Liquid runs out of the blend-
er bowl.
The blender lid, the lid clo-
sure or both parts are not
attached correctly.
Attach the blender lid cor-
rectly and seal it with the lid
closure.
The seal of the blender lid
is broken.
The seal must be exchanged
by customer service.
The blender bowl is over-
filled.
Reduce the number of ingredi-
ents or the quantity.
A program symbol, the dis-
play and the power button
are flashing.
An automatic program
has been interrupted. The
flashing indicates the inter-
ruption.
Press the power button again
to continue the automatic
program.
Fault
Fault

15www.zwilling.com/ca
EN
Problem Possible cause Remedy
All program symbols and
the display on the blender
base are flashing and three
beeps sound.
The blender bowl and the
lid have been removed
during operation.
Reattach the blender bowl or
lid and continue as desired.
The motor has overheated.
Put the selector switch in the
on/off position, unplug the ap-
pliance and wait 30 minutes.
It is not possible to start the
mixing process.
The blender bowl or the lid
is not attached correctly.
Place the blender bowl on the
base with the handle facing to
the right or front or attach the
lid correctly.
The blender has been
stopped and the selector
switch has been moved
with the lid open.
Put the selector switch in the
on/off position, press the pow-
er button and then switch the
appliance back on.
The tamper does not display
any temperature.
The battery for the tamper
is empty. Change the battery.
Customer service
Please contact our customer service should you encounter any problems with your
blender.
Detailed information on service, repairs, warranty and product registration can be
found at
www.zwilling.com/service.
Disposal
With regard to disposal, please return your old appliance to a collection point for electrical
appliances.
Dispose of the battery for the tamper at a collection point for batteries.
Fault / Customer Service / Disposal

ZWILLING J.A. Henckels AG
www.zwilling.com/ca