ZyXEL Communications Prestige 971M User manual

Prestige 630M
ADSL USB Modem
Quick Start Guide

Prestige 630 ADSL USB Modem Quick Start Guide
Table of Contents ii
Table of Contents
Chapter 1 Driver Installation........................................................................................................................1-1
Chapter 2 Install and Configure your Modem..............................................................................................2-1
2.1 Rear Panel Connections ...............................................................................................................2-1
2.2 Front Panel LEDs.........................................................................................................................2-2
2.3 Front Panel LED Descriptions .....................................................................................................2-3
Chapter 3 Troubleshooting...........................................................................................................................3-1

Prestige 630 ADSL USB Modem Quick Start Guide
Driver Installation 1-1
Chapter 1
Driver Installation
This chapter guides you through the software installation for Windows 98 SE, 2000 and ME.
Before starting, close all Windows programs running on your computer and have your installation CD
handy. Also, make sure you have the following information (supplied by your ISP).
ASK YOUR ISP FOR THE FOLLOWING
INFORMATION: FILL IN THE BLANKS
Type of Driver you need to install.
VCI Number
The Virtual Channel Identifier number identifies
virtual channels between users or between users
and networks.
VPI Number
Virtual Path Identifier number identifies virtual paths
between users or between users and networks.
Encapsulation Type
Encapsulation is the method of packaging
information into packets. An example of an
encapsulation type is RFC 1483.
Modulation Type
The Modulation Type selected dictates what ADSL
mode the Prestige will operate under. Use T1.413,
G.DMT, G.LITE or Multimode.
Windows 2000 users can ignore all Digital Signature Not Found alerts and click Yes
to continue.
Step 1. Insert the installation CD into the CD-ROM drive and locate the Setup.exe icon.

Prestige 630 ADSL USB Modem Quick Start Guide
1-2 Driver Installation
Step 2. The Welcome window prompts you to quit the setup procedure and exit all Windows programs
before continuing. Close all open windows and click Next >.
Step 3. Click Yes after reading the contents of the Software License Agreement window.
Step 4. The Select ISP window allows you to specify a DSL service provider. Highlight Other Service
Provider and then click Next >.
Step 5. Select the driver type you want to install in the Select Driver Type window (shown next).
Contact your ISP for this information.
Install the driver that your ISP supports.
Information about Driver Types
Highlight the
driver you
want to
install.
Then click
Next >.
Choose the
language you
want to use.
Then click
OK.

Prestige 630 ADSL USB Modem Quick Start Guide
Driver Installation 1-3
DRIVER AND DESCRIPTION ASSOCIATED ENCAPSULATION
CHOICES (SEE NEXT STEP)
RFC 2364 PPPoATM NULL
RFC 2364 PPPoATM LLC
WAN This driver resembles a dial-up modem. Call
establishment is performed through Dial-Up
Networking. RFC 2516 PPPoE
RFC 1577 Classical IPoATM
RFC 1483 IPoATM Bridged LLC
RFC 1483 IPoATM Bridged VC
RFC 1483 IPoATM Routed LLC
LAN This driver resembles a LAN or Ethernet device.
Connection establishment is automatic.
RFC 1483 IPoATM Routed VC
Step 6. The Communication Settings window allows you to input your communication settings. You
should have obtained this information from your ISP.
Encapsulation field options depend on the driver you selected in the last step.
Modulation field options are briefly explained at the beginning of this chapter.
Enter your VPI.
Enter your VCI.
Select your
Enca
p
sulation.
Select your
Modulation.
Then click Next.

Prestige 630 ADSL USB Modem Quick Start Guide
1-4 Driver Installation
Step 7. The Start Copying Files window lets you to review current settings. Click Customize or Back
to change the settings. Click Next > to accept the current settings. The Setup Complete window
confirms that the files have been copied.
Step 8. Congratulations! You have successfully installed the driver for your modem. Proceed to the
next chapter to install and configure your modem.
Click Finish.

Prestige 630 ADSL USB Modem Quick Start Guide
Install and Configure your Modem 2-1
Chapter 2
Install and Configure your Modem
This chapter shows you how to connect your new hardware and install your modem.
The P630 has two interfaces: a USB and an ADSL port. Both interfaces transmit and receive data through a
USB cable and an ADSL line respectively. LED indicators indicate the operational status of your Prestige.
2.1 Rear Panel Connections
The following figure shows the rear panel connectors of your Prestige.
Do not connect your USB device until you have installed the driver software for
your computer as described in the last chapter.

Prestige 630 ADSL USB Modem Quick Start Guide
2-2 Install and Configure your Modem
Step 1. Plug one end of your RJ-11 cable (included) directly into the wall jack and the other end into the
ADSL port on your Prestige. Optional: connect a telephone microfilter (optional purchase)
between the wall jack and your telephone(s). A microfilter acts as a low pass filter that screens
out possible interference.
Step 2. Attach the rectangular end of the USB cable into the back of your computer and the square end
of the USB cable into the back of your Prestige (see figures below).
Figure 2-2 Plug this cable end into your
computer Figure 2-3 Plug this cable end into your Prestige
Step 3. Your computer should auto-detect your modem and begin installing software on your new
hardware automatically; if not, double-click on the Control Panel icon and the Add New
Hardware icon to start the Add New Hardware Wizard. You will see a series of screens as
Windows installs software on your new hardware.
Step 4. Follow the computer prompts and insert your Windows CD if prompted.
Step 5. The System Setting Change window is the final window of the installation wizard. Click Yes
to restart your computer. Once your computer has restarted, successful installation of the
Prestige USB Modem is complete.
Congratulations, you have successfully installed the Prestige 630 USB Modem! Visit www.zyxel.com to
test your Internet connection and discover more exciting products from ZyXEL!
2.2 Front Panel LEDs
The LED indicators on the front panel indicate the operational status of the Prestige 630. All LEDs are
located on the front panel. All interfaces are located on the back panel. The table under the following
figure describes the LED functions.

Prestige 630 ADSL USB Modem Quick Start Guide
Install and Configure your Modem 2-3
2.3 Front Panel LED Descriptions
LED FUNCTION DESCRIPTION
USB USB Interface
and Modem
Power
Connection
This LED is off when the USB is not connected, has malfunctioned or is
not receiving power.
The LED is on when the USB is connected, receiving power or
transmitting information.
ADSL ADSL Interface This LED is off when the link is not ready, has malfunctioned or is not
receiving power.
This LED is on when the Prestige is connected to the DSLAM and the
link is up or connected.
This LED blinks when the link is not ready or has failed.