360 YIELD CENTER 360 Series User manual

INSTALLATION INSTRUCTIONS
PAGE 1  360YIELDCENTER.COM
V9  3.5.2019
STEP 2 |INSTALL BANDIT UNIT
Use short M12 Bolts 6to install 360 BANDIT unit (long leg
to the rear) using the same holes.
Tighten with 16 mm socket. Torque bolts to 42.2 ft lbs.
Ensure not to over tighten bolts.
NOTE: The 360 BANDIT arms are designed to flex. This may
cause variability in the gap between the pivot arm bolts.
BEFORE NEXT STEP...
Hose guides are labeled “L” left and “R” right. When
holding them in your hands with the ear tabs facing each
other, your left hand will be holding the left side hose guide
and your right hand will be holding the right side.
Left hose guides are indicated with an “L”.
Right hose guides are indicated with an “R”.
HELPFUL TOOLS
• Hammer/Mallet
• Wrench Sizes: 15/16” and 7/16”
• Socket Sizes: 16mm, 15/16”, 18mm and 7/16”
• Impact
• Torque Wrench
NEED HELP?
Call our Product Support Team at 888-512-4890.
lr
6 6
STEP 1 |REMOVE CLOSING SYSTEM
Release spring 1to remove tension from closing system.
NOTE: If the optional chains kit is not being installed do not
remove the closing wheels.
Remove closing wheels 2with a 15/16” socket and wrench.
The bolts and nuts 3can be discarded but the bushings 4
need to be kept.
If present, remove insecticide attachment.
Using an 18mm socket, remove the closing system casting
5and discard the bolts.
12
3 4 5

STEP 5 |ASSEMBLE PLUMBING
NOTE: If hoses are not fully seated in the push to connect,
they will leak. Hoses seat 7/8” of an inch deep or until you
hear a snap.
Install orifice plates 1in the rubber grommets 1.
Assemble pluming components in the arrangement shown
above 1. The supplied push to connect adapter in the 360
BANDIT kit connects to 3/8” push to connect compatible hose.
Secure hoses to row unit with provided zip ties 1.
PLUMBING RECOMMENDATIONS:
To prevent excess fertilizer from dribbling out of the hoses
when product application is shut o, install one push to
connect polypropylene (Inlet x Outlet) 3/8” O.D. check valve
(not included) in the plumbing to each row prior to the 360
BANDIT orifices. Check valve is available at Dultmeier Sales
(Item #BUCV1103-P38).
A 50 mesh strainer (not included) can be used in the
complete plumbing system between tanks and 360
BANDIT to help prevent debris from blocking orifices.
INSTALLATION COMPLETE
STEP 4 |REINSTALL CLOSING SYSTEM
Use long M12 bolts, washers, and nuts 7to attach closing
system casting to the 360 BANDIT unit.
Torque bolts to 42.2 ft lbs. Ensure not to over tighten bolts.
Reinstall insecticide attachment, if present.
NOTES:
If the closing wheels were removed but you are not
installing the optional Chain Kit, reinstall the closing
wheels at this time.
If the optional Chain Kit is being installed, do not reinstall
the closing wheels.
If pinning up 360 BANDIT disks while running spiked closing
wheels, mount spiked closing wheels in rear most hole.
INSTALLATION INSTRUCTIONS
PAGE 2  360YIELDCENTER.COM
12
12
13 14
13
14
15
15
16
16
STEP 3 | INSTALL DISK & HOSE GUIDES
NOTE: The supplied 3/8” x 1” bolt installed in the Bandit pin
up hole is to be used as a “zero” setting and as a stop in case
of spring disengagement.
Insert 5/8” X 3” bolt through the disk. Insert bushing 7
(large side first) and hose guide assembly 8(ear tab facing out).
Slide assembly into the lower hole on the bandit 9, aligning
the ear tab with corresponding upper hole 1and secure
with lock nut.
Tighten with 15/16” socket and wrench.
Using a mallet, install provided dust caps over bolt heads.
Route application hose through hole in top of 360 BANDIT
frame 1.
Repeat for other side.
10
11
8
7
9
10
11