360 Yield 360 Y-DROP HAGIE DELTA BOOM User manual

INSTRUCTIONS
360 YDROP®
HAGIE DELTA BOOM
360 Y-DROP®REGISTRATION
Please visit productregistration.360yieldcenter.com
to complete the product registration for your
360 Y-DROP so we can better support our products
from day one and ensure you have the latest
upgrades, warranty parts and technical support.
Thank you!
360YIELDCENTER.COM
V1  01.25.2017

INSTRUCTIONS
360 YDROP
HAGIE DELTA BOOM
2
INTRODUCTION
Before beginning, it’s important to know where each mounting bracket fits relative
to the row spacing involved. The 360 Y-DROP unit should be precisely centered
on the machine, as this is critical to the assembly of the system to the sprayer and
for mounting the system to your sprayer boom. There are, however, many boom
variations among all sprayer models. Your sprayer may not be identical to the model
in the following steps of the guide, and the pictures may not exactly reflect your
model. While these steps will help you install most of your 360 Y-DROP system,
you may need to custom-fit some components with your particular boom.
RECOMMENDED TOOLS
Ratchet wrench with 1/2" and 9/16" deep well sockets
3/8" 12-point socket
1/2" and 9/16" combination wrenches
#2 Phillips screwdriver (for the shield installation)
TORQUE VALUES
Refer to these torque values when tightening all fasteners
5/16" stainless U-bolt 15 ft/lbs
5/16" stainless Set screw 15 ft/lbs
3/8" carbon U-bolt 35 ft/lbs
5/16" carbon U-bolt 30 ft/lbs
5/16" carbon Stop bolt 30 ft/lbs
QUESTIONS
Call our Product Support team at 888-512-4890

INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM
360YIELDCENTER.COM
3
ESTABLISH
DROP LOCATIONS
Figures 1 and 2
Step 1 Locate the center of the machine and
identify the location of all the drops. On
the sprayer boom, mark where each riser
mount will be located. This will ensure
that the extension tubes will not interfere
with the riser mounts.
Figure 3
Step 2 Starting at the wing fold pivot pin on
the primary boom, measure and mark
points at 59", 120", 179"; 241" and 301"
(all measurements are ±5"). Repeat for
the other primary boom.
I.
Figure 2
Figure 1
Figure 3
59"
120"
179"
241"
301"

INSTALL MOUNT ASSEMBLIES
ON THE OEM PRIMARY BOOM
Figures 4 and 5
Step 1 With the threads pointing down, install
U-bolt (1) on the bottom side of the
OEM primary boom.
Bag AB
Step 2 Install bracket assembly (2) and flange
nuts.
Hardware Kit D
Step 3 Install extension tube (3).
Step 4 Install boom bracket (4) onto the
extension tube.
Step 5 Install stop bolts at both the front
and the rear of the extension tube.
Hardware Kit B
Step 6 Install stainless steel set screw (5) and the
jam nut assembly onto both OEM bracket
assembly and Y-DROP boom bracket
assembly.
Hardware Kit D
Repeat Steps 1-6 the remaining mount assemblies
on the OEM primary boom.
II.
Figure 4
Figure 5
360YIELDCENTER.COM
2
1
4
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM
34
5

360YIELDCENTER.COM
5
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM
Figure 6
Figure 7
Figure 8
Figure9
INSTALL CENTER SECTION
SQUARE TUBE UPGRADE
Figure 6
Step 1 Place top plate (1) on top of the center
section and install two bolts (2) with
washers and carriage bolts (3). Note the
carriage bolt at the rear of the boom will
need to be set in place on the 14" top
plate before it is installed in Step 2.
Figure 7
Step 2 Place 14" top plate (1) and bracket
assemblies (2) into position, then install
four flange nuts (3).
Step 3 Install extension tube (4) onto bracket
assembly (2).
Step 4 Install boom bracket (5).
Figure 8
Step 5 Install stainless steel set screw (1) and
the jam nut assembly onto both OEM
bracket assembly and Y-DROP boom
bracket assembly.
Step 6 Install square U-bolt (2), the 5/16" extra
thick washers and the 5/16" nuts.
Hardware Kit A
Repeat steps 1-6 for second center section mount.
III.
2
1
4
5
3
1
1
2
2
3

360YIELDCENTER.COM
6
INSTALL 360 YDROP
BOOM
Figure 10
Step 1 Assemble 5' boom sections (1) utilizing
8" boom connectors (2) and the supplied
hardware.
Hardware Bag CC
Step 2 Repeat Step 1 as needed in order to
assemble the entire 360 Y-DROP boom.
Step 3 Set the 360 Y-DROP boom assembly
onto boom bracket (3).
Repeat Steps 1 -3 for the remaining boom assemblies.
CAUTION: The 360 Y-DROP boom assembly may
weigh up to 150 lbs. (68 kg). Exercise caution and
enlist help for this process.
Figure 11
Step 4 In order to span the full length of the
center section 360 Y-DROP boom, you
will need to cut and drill one of the 5'
boom sections to 1'. Mount this 1' section
between two full 5' boom sections. Drill a
7/16" through hole centered 2" from the
outside edge.
Figures 12 and 13
Step 5 Install square U-bolt (1), the 5/16" extra
thick washers, and the 5/16" nuts over
the 360 Y-DROP boom (2).
Hardware Kit A
Step 6 Install stop bolt (3) at the both the front
and the rear of the extension tube.
Repeat for remaining stop bolts.
Hardware Kit B
Step 7 Install stainless steel set screw and
jam nut assembly (4). See Figure 16 for
detail. Repeat for the remaining mount
assemblies on the primary boom.
IV.
Figure 10
Figure 11
Figure 12
Figure 13
1
2
4
4
3
3
1
2
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM

360YIELDCENTER.COM
7
INSTALL YOKE ASSEMBLIES
ON THE OEM PRIMARY BOOM
Figure 14
Step 1 With the U-bolt pointing to the front,
install the yoke mount (1) and flange
nuts to upper boom section.
Step 2 With the square U-bolt threads pointing
up and using the extra thick washer and
Nylock nut, install yoke mount (2) to the
360 Y-DROP boom section.
Step 3 Using pins, install the yoke straps (3)
between the upper boom and 360
Y-DROP boom. Using the flange nuts,
tighten the 1-1/4" carriage bolts.
Repeat Steps 1-3 for the remaining yokes on
the OEM primary booms. Yokes should be spaced
approximately 60" (±5”) apart.
V. 2
Figure 14
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM
2
1
3

360YIELDCENTER.COM
8
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM
INSTALL BREAKAWAY ASSEMBLY 
ONE PIECE
Figure 15
Step 1 Install breakaway assembly - one piece (1)
using the square U-bolts (2) and the extra
thick washer and Nylock nut. Repeat for
the remaining breakaway assemblies -
one piece.
Hardware Kit C
Figure 16
Figure 16 may show more or fewer mounts than
your installation. The alignment and quantity of the
mounts will depend on your row spacing.
Figure 17
Step 2 Install riser tube assembly (1) into the
breakaway assembly - one piece (2).
Step 3 Install pin (3).
Repeat Steps 2 and 3 for the remaining riser tube
assemblies.
NOTE: Included in most sprayer mount packages
are standard riser mounts to be used when primary
booms are folded and in transport mode. These
standard riser mounts should be mounted in
locations that allow you to relocate the drops away
from potential tire interference. See “Install Riser
Mounts Without Breakaway Assemblies” section on
next page for more instructions.
VI.
Figure 15
Figure 16
Figure 17
1
2
2
3

360YIELDCENTER.COM
9
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM
INSTALL RISER MOUNTS WITHOUT
BREAKAWAY ASSEMBLIES (OPTIONAL)
Figure 18
Step 1 Install riser mount (1) using the square
U-bolts (2) and the extra thick washer
and Nylock nut. Repeat for the remaining
riser mounts.
Hardware Kit C
Figure 19
Figure 20 may show more or fewer riser mounts
than your installation. The alignment and quantity
of the riser mounts will depend on your row spacing.
Figure 20
Step 2 Install riser tube assembly (1) into the
riser mount (2).
Step 3 Install pin (3).
Repeat Steps 2 and 3 for the remaining riser tube
assemblies.
VI.
Figure 19
Figure 20
2
3
1
Figure 18
2
1

360YIELDCENTER.COM
10
Figure 21
Figure 22
Figure 23
INSTALL SHIELDS AND
RISER HOSES
Figure 21
Step 1 Install shield (1) onto riser tube (2).
Figure 22
Step 2 Install base unit (1) onto riser tube (2).
Figure 23
Step 3 Assemble drag hoses (1) to 360 Y-DROP
base and secure with hose clamps (2).
Figure 24
Step 4 Note the orientation of the drag hose
clamps. The tails should point inward.
VII.
Figure 24
2
2
1
1
2
1
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM

360YIELDCENTER.COM
All other trademarks are the property of 360 Yield Center, its ailiates and/or its licensors.
©2017 360 Yield Center. All rights reserved.
Figure 25
Figure 26
Figure 27
INSTALL SHIELDS AND
RISER HOSES (CONTINUED)
Figure 25
CAUTION: Do NOT use a drill or impact driver
for Steps 5 and 6.
Step 5 Install two ½" screws (1).
Step 6 Install two ¾" screws (2).
Step 7 Install rubber washer (3) into the “Y”.
Figure 26
Step 8 Install riser hose assembly (1) into the “Y”.
Figure 27
Step 9 Route riser hose assembly (1) as shown
in Figure 24.
Step 10 Install the riser hose assembly to the
OEM nozzle body.
Step 11 Use 3 equally spaced plastic ties to
secure the riser hose assembly.
Repeat Steps 1-11 for the remaining
360 Y-DROP Shields.
VII.
INSTALLATION COMPLETE.
11
1
1
3
2
INSTRUCTIONS 360 YDROP
HAGIE DELTA BOOM