360 Yield 360 Y-DROP HAGIE DTS 2016 + User manual

INSTRUCTIONS
360 YDROP®
HAGIE DTS 2016 +
360 Y-DROP®REGISTRATION
Please visit productregistration.360yieldcenter.com
to complete the product registration for your
360 Y-DROP so we can better support our products
from day one and ensure you have the latest
upgrades, warranty parts and technical support.
Thank you!
360YIELDCENTER.COM
V1  01.25.2017

INSTRUCTIONS
360 YDROP
HAGIE DTS 2016 +
INTRODUCTION
Before beginning, it’s important to know where each mounting bracket fits relative
to the row spacing involved. The 360 Y-DROP unit should be precisely centered
on the machine, as this is critical to the assembly of the system to the sprayer and
for mounting the system to your sprayer boom. There are, however, many boom
variations among all sprayer models. Your sprayer may not be identical to the model
in the following steps of the guide, and the pictures may not exactly reflect your
model. While these steps will help you install most of your 360 Y-DROP system,
you may need to custom-fit some components with your particular boom.
RECOMMENDED TOOLS
Ratchet wrench with 1/2" and 9/16" deep well sockets
3/8" 12-point socket
1/2" and 9/16" combination wrenches
#2 Phillips screwdriver (for the shield installation)
Drill with 7/16” drill bit
TORQUE VALUES
Refer to these torque values when tightening all fasteners
5/16" stainless U-bolt 15 ft/lbs
5/16" stainless Set screw 15 ft/lbs
3/8" carbon U-bolt 35 ft/lbs
5/16" carbon U-bolt 30 ft/lbs
5/16" carbon Stop bolt 30 ft/lbs
QUESTIONS
Call our Product Support team at 888-512-4890
2

ESTABLISH
DROP LOCATIONS
Figures 1 and 2
Step 1 Locate the center of the machine and
identify the location of all the drops. On
the sprayer boom, mark where each riser
mount will be located. This will ensure
that the extension tubes will not interfere
with the riser mounts.
Figure 3
Step 2 Starting at the wing fold pivot pin on
the primary boom, measure and mark
points at 40", 100", 160"; 220" and 280"
(all measurements are ±5"). Repeat for
the other primary boom.
INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
I.
Figure 1
Figure 2
Figure 3
360YIELDCENTER.COM
3
40" 100" 160" 220" 280"

INSTALL PRIMARY BOOM SPRAYER
MOUNT PACKAGE
Figures 4
To prepare for the steps that follow, you will need
to drill two 7/16" holes at mounting location 1 (40"
+/-5" from the pivot pin) on both OEM Primary
booms. This will allow for the installation of the
first mounting position of the square U-bolt on the
front and rear OEM booms.
Figures 5 and 6
Step 1 With the thread pointing down, install
square U-bolts (1) on the top of the OEM
primary boom.
Bag AF (2.0")
Bag AG (2.5")
Step 2 Install bracket assemblies (2) and the
flange nuts.
Hardware Kit D
Figure 7
Step 3 Install extension tube (3).
Step 4 Install boom bracket (4) onto extension
tube (3).
Repeat Steps 1-4 for the remaining mounting
positions on the primary booms.
INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
II.
Figure 6
Figure 7
360YIELDCENTER.COM
4
1
2
3
4
1
2
2.5"
2.5"
2.0"
2.0"
2.0"
Figure 4
Figure 5

INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
III.
360YIELDCENTER.COM
5
INSTALL CENTER SECTION
SQUARE TUBE
Figures 9 and 10
Step 1 Install u-bolt (1) and 14" top
plate (2) using the supplied hardware.
Step 2 Install bracket assemblies (3).
NOTE: Install OEM mount bracket kits so that the
set screws are pointing inward to ensure clearance
when the primary booms are folded (see Figure 11).
Step 3 Install extension tube (4).
Step 4 Install 360 Y-DROP boom bracket (5)
on extension tube (4).
Bag BB
Step 5 Install stop bolt assemblies (6).
Hardware Kit B within Bag BB
Step 6 Install set screws (7) on bracket
assemblies.
Hardware Kit D within the Center Section Kit
Step 7 Install the set screw on Y-DROP boom
bracket.
Hardware Kit D within the Center Section Kit
Repeat steps 1-7 for the remainder of the
center section support assemblies.
Figure 9
Figure 10
Figure 11
4
5
1
6
3
7
2
Figure 8

INSTALL 360 YDROP
BOOM
Figure 12
Step 1 Assemble 5' boom sections (1) utilizing
8" boom connectors (2) and the supplied
hardware.
Hardware Bag CC
Step 2 Repeat Step 1 as needed in order to
assemble the entire 360 Y-DROP boom.
Step 3 Set the 360 Y-DROP boom assembly
onto boom bracket (3).
Repeat Steps 1 -3 for the remaining boom assemblies.
CAUTION: The 360 Y-DROP boom assembly may
weigh up to 150 lbs. (68 kg). Exercise caution and
enlist help for this process.
Figure 13
Step 4 In order to span the full length of the
center section 360 Y-DROP boom, you
will need to cut and drill one of the 5'
boom sections to 1'. Mount this 1' section
between two full 5' boom sections. Drill a
7/16" through hole centered 2" from the
outside edge.
Figures 14 and 15
Step 5 Install square U-bolt (1), the 5/16" extra
thick washers, and the 5/16" nuts over
the 360 Y-DROP boom (2).
Hardware Kit A
Step 6 Install stop bolt (3) at the both the front
and the rear of the extension tube.
Repeat for remaining stop bolts.
Hardware Kit B
Step 7 Install stainless steel set screw and
jam nut assembly (4). See Figure 12 for
detail. Repeat for the remaining mount
assemblies on the primary boom.
INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
IV.
Figure 12
Figure 13
Figure 14
Figure 15
360YIELDCENTER.COM
1
2
4
4
3
6
3
1
2

INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
360YIELDCENTER.COM
7
INSTALL BREAKAWAY ASSEMBLY 
ONE PIECE
Figure 16
Step 1 Install breakaway assembly - one piece (1)
using the square U-bolts (2) and the extra
thick washer and Nylock nut. Repeat for
the remaining breakaway assemblies -
one piece.
Hardware Kit C
Figure 17
Figure 17 may show more or fewer mounts than
your installation. The alignment and quantity of the
mounts will depend on your row spacing.
Figure 18
Step 2 Install riser tube assembly (1) into the
breakaway assembly - one piece (2).
Step 3 Install pin (3).
Repeat Steps 2 and 3 for the remaining riser tube
assemblies.
NOTE: Included in most sprayer mount packages
are standard riser mounts to be used when primary
booms are folded and in transport mode. These
standard riser mounts should be mounted in
locations that allow you to relocate the drops away
from potential tire interference. See “Install Riser
Mounts Without Breakaway Assemblies” section on
next page for more instructions.
V.
Figure 16
Figure 17
Figure 18
1
2
2
3
1

INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
360YIELDCENTER.COM
8
INSTALL RISER MOUNTS WITHOUT
BREAKAWAY ASSEMBLIES OPTIONAL
Figure 19
Step 1 Install riser mount (1) using the square
U-bolts (2) and the extra thick washer
and nylock nut. Repeat for the remaining
riser mounts.
Hardware Kit C
Figure 20
Figure 20 may show more or fewer riser mounts
than your installation. The alignment and quantity
of the riser mounts will depend on your row spacing.
Figure 21
Step 2 Install riser tube assembly (1) into the
riser mount (2).
Step 3 Install pin (3).
Repeat Steps 2 and 3 for the remaining riser tube
assemblies.
V.
Figure 19
Figure 20
Figure 21
1
2
2
3
1

INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
Figure 22
Figure 23
Figure 24
360YIELDCENTER.COM
INSTALL SHIELDS AND
RISER HOSES
Figure 22
Step 1 Install shield (1) onto riser tube (2).
Figure 23
Step 2 Install base unit (1) onto riser tube (2).
Figure 24
Step 3 Assemble drag hoses (1) to 360 Y-DROP
base and secure with hose clamps (2).
Figure 25
Step 4 Note the orientation of the drag hose
clamps. The tails should point inward.
VI.
Figure 25
9
2
2
1
1
2
1

INSTRUCTIONS 360 YDROP
HAGIE DTS 2016 +
Figure 26
Figure 27
Figure 28
INSTALL SHIELDS AND
RISER HOSES (CONTINUED)
Figure 26
CAUTION: Do NOT use a drill or impact driver
for Steps 5 and 6.
Step 5 Install two ½" screws (1).
Step 6 Install two ¾" screws (2).
Step 7 Install rubber washer (3) into the “Y”.
Figure 27
Step 8 Install riser hose assembly (1) into the “Y”.
Figure 28
Step 9 Route riser hose assembly (1) as shown
in Figure 28.
Step 10 Install the riser hose assembly to the
OEM nozzle body.
Step 11 Use 3 equally spaced plastic ties to
secure the riser hose assembly.
Repeat Steps 1-11 for the remaining
360 Y-DROP Shields.
VI.
INSTALLATION COMPLETE.
360YIELDCENTER.COM
All other trademarks are the property of 360 Yield Center, its ailiates and/or its licensors.
©2017 360 Yield Center. All rights reserved.
11
1
1
3
2