360 Yield 360 Y-DROP JOHN DEERE 4630 User manual

INSTRUCTIONS
360 YDROP®
JOHN DEERE 4630
360 Y-DROP®REGISTRATION
Please visit productregistration.360yieldcenter.com
to complete the product registration for your
360 Y-DROP so we can better support our products
from day one and ensure you have the latest
upgrades, warranty parts and technical support.
Thank you!
360YIELDCENTER.COM
V1  12.22.2016

INSTRUCTIONS
360 YDROP
JOHN DEERE 4630
INTRODUCTION
Before beginning, it’s important to know where each mounting bracket fits relative
to the row spacing involved. The 360 Y-DROP unit should be precisely centered
on the machine, as this is critical to the assembly of the system to the sprayer and
for mounting the system to your sprayer boom. There are, however, many boom
variations among all sprayer models. Your sprayer may not be identical to the model
in the following steps of the guide, and the pictures may not exactly reflect your
model. While these steps will help you install most of your 360 Y-DROP system,
you may need to custom-fit some components with your particular boom.
RECOMMENDED TOOLS
Ratchet wrench with 1/2" and 9/16" deep well sockets
3/8" 12-point socket
1/2" and 9/16" combination wrenches
#2 Phillips screwdriver (for the shield installation)
TORQUE VALUES
Refer to these torque values when tightening all fasteners
5/16" stainless U-bolt 15 ft/lbs
5/16" stainless Set screw 15 ft/lbs
3/8" carbon U-bolt 35 ft/lbs
5/16" carbon U-bolt 30 ft/lbs
5/16" carbon Stop bolt 30 ft/lbs
QUESTIONS
Call our Product Support team at 888-512-4890
2

ESTABLISH
DROP LOCATIONS
Figures 1 and 2
Step 1 Locate the center of the machine and
identify the location of all the drops. On
the sprayer boom, mark where each riser
mount will be located. This will ensure
that the extension tubes will not interfere
with the riser mounts.
Figure 3
Step 2 Starting at the wing fold pivot pin on
the primary boom, measure and mark
points at 69", 133", 210", 267" and 310"
(all measurements are ±5"). Repeat for
the other primary boom.
INSTRUCTIONS 360 YDROP
JOHN DEERE 4630
I.
Figure 1
Figure 2
Figure 3
360YIELDCENTER.COM
3
69"
133"
210"
267"
310"

INSTALL PRIMARY BOOM SPRAYER
MOUNT PACKAGE
Figure 4
Step 1 With the thread pointing down, install
square U-bolt (1) on the top of the OEM
primary boom.
Bag AG
Step 2 Install bracket assembly (2) and flange
lock nut (3).
Hardware Kit D
Repeat Steps 1 and 2 for the other OEM
mount bracket.
Step 3 Install extension tube (4).
Repeat Steps 1-3 for the remaining mounting
positions on the primary booms.
Figure 5
Step 4 Install boom bracket (1) onto extension
tube (2).
INSTRUCTIONS 360 YDROP
JOHN DEERE 4630
II.
Figure 4
Figure 5
360YIELDCENTER.COM
4
1
2
3
4
2
1

INSTALL CENTER SECTION
EXTENSION TUBE
Figures 6 and 7
Step 1 Install 14" top plate (1) and 8" top plate (2)
using the supplied hardware.
Step 2 Install bracket assemblies (3).
Step 3 Install extension tube (4).
Step 4 Install drop tube (5) onto the extention
tube (4) and install bolt assembly (6).
Hardware Kit B
Step 5 Install stainless steel set screw and jam
nut assembly.
Step 6 Install stop bolt at the rear of the exten-
tion tube.
Hardware Kit D
Repeat Steps 1-6 for the other center section
extension tube assembly.
INSTRUCTIONS 360 YDROP
JOHN DEERE 4630
III.
Figure 6
Figure 7
360YIELDCENTER.COM
5
2
1
2
3
3
4
5
4
36