3One data IPMC100 Series Operating and maintenance instructions

IPMC100 Series
Industrial POE Media Converter
Quick Installation Manual
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Tel:
[phone]
Fax:
[phone]
【Package Checklist】
Please check whether the package and accessories are intact
while using the converter for the first time.
1. Media converter with wiring terminal block×1
2. Quick installation guide 3. DIN-Rail mounting attachment
4. Certification 5. Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
The series products are unmanaged industrial POE media
converters. Models as follow:
ModelI. IPMC100-1GF-1GPOE(1Gigabitfiber+ 1GigabitPOE)
ModelII. IPMC100-1GF-2GPOE(1Gigabitfiber+ 2GigabitPOE)
ModelIII. IPMC100-1GS-1GPOE (1 Gigabit SFP+1GigabitPOE)
ModelIV. IPMC100-1GS-2GPOE (1 Gigabit SFP+2GigabitPOE)
【Panel Design】
Rear view, Top view and Bottom view
Front view and Side view
Model I Model II
Model III Model IV
1. DIN-Rail mounting kit
2. Grounding screw
3. 3-pin terminal block for power input
4. DIP switch
5. Device running indicator RUN
6. Copper port LFP indicator
7. Fiber port LFP indicator
8. Interface connection status indicator
9. 1000Base-FX fiber port
10. POE port power supply status indicator
11. 10/100/1000 Base-T(X) POE port
12. 100/1000 Base-SFP slot
【Mounting Dimension】
Unit: mm
【DIN-Rail Mounting】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:
Check if the DIN-Rail mounting kit is installed firmly.Step 1 Insert the bottom of DIN-Rail mounting kit (one sideStep 2 with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed onStep 3

DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Device power off.Step 1 After lift the device upward slightly, first shift out theStep 2 top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
Note:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Power Supply Connection】
DC power supply
This series media converter provides 3-pin
industrial terminals (1, 2, 3). 1 is positive pole,
2 is shell ground, 3 is negative pole.
Power Range: 12 ~ 48VDC (POE48VDC).
Note:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【DIP Switch Setting】
Provide 4-pin DIP switch for function setting,
where "ON" is enable valid terminal. Please
power off and power on after changing the status
of DIP switch. DIP switch 1~4 define as follow:
1. Standard PD / LEGACY PD switching (default is OFF,
the standard PD resistance detection).
2. Jumbo frame enabled.
3. Supports two definitions. Model I and model III: LFP
enabled; model II and model IV: Flow control.
4 Force copper port 100M speed.
【Checking LED Indicator】
The device provides LED indicators to monitor the device
working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Status
Description
LFP (TX)
ON
Copper port link fault alarm.
OFF
Copper port link is normal.
LFP (FX)
ON
Optical fiber port link fault alarm.
OFF
Optical fiber port link is normal.
RUN
ON
The device is powered on or the
device is abnormal.
OFF
The device is powered off or the
device is abnormal.
Blinking
System is running well.
POE
ON
POE port for PD device normal
power supply.
Blinking
POE port is in detection or fault
status.
OFF
POE port is not connected with
the PD device.
G1~G2/G3
ON
Port has established a valid
network connection.
Blinking
Port is in network communication.
OFF
Port has not established a valid
network connection.
【Specification】
Panel
Gigabit POE port
10/100/1000 Base-T(X) adaptive,
full-duplex/half-duplex adaptive and
MDI/MDI-X adaptive;
PoE port, the maximum output
power is 30W.
POE pins
V +, V +, V-, V- corresponds to pins
1, 2, 3, 6.
Gigabit fiber port
1000 Base-FX, the optical port is a
full duplex SC/ST/FC single mode
or multimode interface.
Gigabit SFP slot
100/1000 Base-SFP
Indicator
LFP indicator, run indicator,
interface indicator, POE indicator
Exchange attributes
Backplane bandwidth
14G
Packet buffer size
1Mbit
MAC table size
8K
Power supply
Input power supply
12~48VDC (POE48VDC)
Access terminal
3-pin 7.62mm pitch terminal block
Consumption
IPMC100-1GF-1GPOE
No-load: 1.44W@48VDC
Full-load: 28.51W@48VDC
IPMC100-1GF-2GPOE
No-load: 5.14W@48VDC
Full-load: 55.30W@48VDC
IPMC100-1GS-1GPOE
No-load: .1.49W@48VDC
Full-load: 27.55W@48VDC
IPMC100-1GS-2GPOE
No-load: 2.11W@48VDC
Full-load: 53.76W@48VDC
Working environment
Working temperature
-40℃～80℃
Storage temperature
-40℃～85℃
Working humidity
5%～95% (no condensation)
Protection grade
IP40 (metal shell)