Aaeon EMB-BSW1 User manual

EMB-BSW1
Industrial Motherboard

E11481
First Edition
March 2016
Copyright Notice
This document is copyrighted, 2016. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products described
in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of the original
manufacturer. Information provided in this manual is intended to be accurate and
reliable. However, the original manufacturer assumes no responsibility for its use,
or for any infringements upon the rights of third parties that may result from its use.
The material in this document is for product information only and is subject
to change without notice. While reasonable efforts have been made in the
preparation of this document to assure its accuracy, the original manufacturer
assumes no liabilities resulting from errors or omissions in this document, or from
the use of the information contained herein.
The original manufacturer reserves the right to make changes in the product
design without notice to its users.
Acknowledgments
All other products’ name or trademarks are properties of their respective owners.
• AMI is a trademark of American Megatrends Inc.
• Intel®, Core™ are trademarks of Intel®Corporation.
• Microsoft Windows®is a registered trademark of Microsoft Corp.
• ITE is a trademark of Integrated Technology Express, Inc.
• IBM, PC/AT, PS/2, and VGA are trademarks of International Business
Machines Corporation.
The original manufacturer reserves the right to make changes in the product
design without notice to its users.
All other product names or trademarks are properties of their respective owners.
ii

Contents
Chapter 1: Product overview
1.1 Package contents......................................................................... 1-1
1.2 Features ........................................................................................ 1-1
1.3 Specications............................................................................... 1-2
Chapter 2: Motherboard information
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard layout...................................................................... 2-2
2.3 Screw size..................................................................................... 2-4
2.3.1 Component side.............................................................. 2-4
2.3.2 Solder side ...................................................................... 2-5
2.4 Central Processing Unit (CPU) ................................................... 2-6
2.5 System memory ........................................................................... 2-6
2.6 Jumpers ........................................................................................ 2-7
2.7 Connectors ................................................................................. 2-10
2.7.1 Rear panel connectors.................................................. 2-10
2.7.2 Internal connectors ....................................................... 2-11
Chapter 3: BIOS setup
3.1 BIOS setup.................................................................................... 3-1
3.2 Main menu .................................................................................... 3-2
3.2.1 System Date [Day MM/DD/YYYY] .................................. 3-2
3.2.2 System Time [HH:MM:SS] .............................................. 3-2
3.3 Advanced menu ........................................................................... 3-2
3.3.1 CPUConguration .......................................................... 3-2
3.3.2 SATAConguration ........................................................ 3-3
3.3.3 USBConguration .......................................................... 3-3
3.3.4 Hardware Monitor ........................................................... 3-3
3.3.5 Trusted Computing ......................................................... 3-4
3.3.6 SIOConguration ........................................................... 3-4
3.3.7 Power Management........................................................ 3-5
3.3.8 DigitalIOPortConguration ........................................... 3-5
3.4 Chipset menu ............................................................................... 3-6
3.4.1 North Bridge.................................................................... 3-6
3.4.2 South Bridge ................................................................... 3-6
iii

3.5 Security menu .............................................................................. 3-6
3.5.1 Administrator Password .................................................. 3-6
3.5.2 User Password................................................................ 3-7
3.6 Boot menu .................................................................................... 3-7
3.6.1 BootConguration .......................................................... 3-7
3.6.2 Boot Option Priorities ...................................................... 3-8
3.7 Save & Exit menu......................................................................... 3-8
Appendix
Notices.......................................................................................................A-1
Contents
iv

1.1 Package contents
Check your industrial motherboard package for the following items.
1 x Industrial Motherboard
1 x SATA cable
1 x SATA power cable
1 x I/O shield
1 x Support DVD
NOTE: If any of the above items are damaged or missing, contact your
distributor or sales representative immediately.
1.2 Features
• Integrated Intel®Atom™ Processor N3710/N3060
• Two Dual Channel DDR3L 1600MHz SO-DIMM up to 8GB
• Realtek®ALC32366-ChannelHighDenitionAudioCODEC
• Multi Display: HDMI + HDMI + LVDS, HDMI + HDMI + eDP
• DualEthernetLAN:Intel®i211AT x 2
• SATA 6Gb/s x 3, USB2.0 x 6, USB3.0 x 4, COM x 6
• 1 x Half-height Mini Card Slot with PCIe and USB Interface, 1 x Full-height
Mini Card Slot with mSATA Interface
Chapter 1
Product overview
1-1
Chapter 1: General information

1.3 Specications
SYSTEM
CPU N3710, Braswell-M/D (4C @ 2.56GHz CPU [Burst Mode], 700MHz GFX
(Turbo), ~6W TDP)
N3060, Braswell-M/D (2C @ 2.48GHz CPU [Burst Mode], 600MHz GFX
(Turbo), ~6W TDP)
Memory 2 x SO-DIMM, max. 8GB, DDR3L 1600MHz,
non-ECC,un-bufferedmemory,horizontaltype
Dual channel memory architecture
I/O Chipset F81866D
LAN 1 x Intel®i211AT
1 x Intel®i211AT via AsMedia 1184e
Audio Realtek®ALC3236
TPM InneonSLB96xxTT1.2/2.0onboard(Default:No)
Expansion slots 1 x Half-size Mini Card (PCIe +USB)
1 x Full-size Mini Card (mSATA) via AsMedia 1184e at least 60mm length
(PCIe + USB optional)
BIOS 64Mb Flash ROM, AMI BIOS
H/W Status Monitor Monitors CPU/system temperature
Monitors Vcore, 3.3V/5V/12V voltages
Monitors chassis fan speed
Watchdog Timer 1~255 steps by software program
Smart Fan Control Chassis fan (fanless)
Wake On LAN / PXE Yes(WOL,PXE)
Power States S3, S4, S5
Graphics
Graphics Chipset Intel®HD Graphics
Graphics Multi
Display
HDMI + HDMI + LVDS (Default)
HDMI + HDMI + eDP (BOM change)
HDMI Resolution Up to 2560 x 1600 @60 Hz, 3840 x 2160 @30Hz
LVDS / eDP Upto1920x1080@60Hz,DaulChannel18/24bit(viaCH7511)
eDP up to 2560 x 1440 @60Hz
Backlight Control Voltage / PWM, use HW control
Environment, Power, and ME
Battery Lithium battery
Power requirement 12-24V DC (wide range: 12V-5% ~ 24V+10%)
Operating
temperature 32oF~140oF (0oC~60oC)
Operating humidity 0%~90%relativehumidity,non-condensing
Certicate CE,FCC(ClassA)
Form factor Mini-ITX form factor:
6.7 in. x 6.7 in. (17.0 cm x 17.0 cm)
Weight 1.1 lb (0.5 Kg)
(continued on the next page)
EMB-BSW1
1-2

I/O
Storage 3 x SATA 6Gb/s
1 x SATA power connector (5V / 12V @1A)
USB 2 x USB 3.0 ports (at back panel)
2 x USB 3.0 ports (internal box header)
4 x USB 2.0 ports (2 ports for header, 2 ports for minicard)
4xUSB2.0portsviaASIXMCS9990(internalboxheader)(Default:No)
Display I/O 1 x LVDS (eDP optional by BOM change), 2 x HDMI
Audio I/O Mic-In, Line-Out, internal speaker
LAN I/O 2 x RJ-45 ports on rear I/O
Serial ports 5 x RS-232
1 x RS-232/422/485 supports 5V/12V/RI option (COM1)
PS/2 keyboard/
mouse port Yes(WOL/PXE)
DIO 8-bit Digital I/O interface (4-in / 4-out)
Fan 1 x Chassis fan connector (4-pin)
I/O Placement
Back panel I/O ports
(Lowprole)
1 x DC port (12V~24V, screw type)
2 x USB 3.0 ports
2 x LAN (RJ-45) ports
2 x HDMI ports
1 x Audio jack (Line-Out), green
1 x Audio jack (Mic-in), pink
Internal I/O
connectors
1 x Mini Card slot (half-size Height=4mm)
1xMiniCardslot(full-sizeHeight=9.9mm)
1 x P/S2 header
3 x SATA 6.0 connectors
1 x SATA power connector
1 x USB 3.0 headers support additional 2 USB ports (2 x 10PIN, p=2.00mm)
3 x USB 2.0 headers support additional 6 USB ports (2 x 5PIN, p=2.00mm),
(Default:1 header onboard)
1 x Chassis fan connector
5 x boxer headers for COM (RS-232)
1 x boxer header for COM (RS-232 / 422 / 485)
1 x Digital I/O connector (4-in / 4-out)
1 x 40-pin LVDS / eDP connector (colay)
1 x LVDS 3V / 5V jumper
1 x LCD DC / PWM mode jumper
1 x LCD backlight connector (inverter)
1 x LCD backlight 12V / 5V jumper
1 x Battery horizontal socket
2 x Internal speaker (2W)
1 x 2*2 PIN DCIN 12V AUX power connector
1 x System panel connector
1 x AT/ATX mode select jumper (optional)
1 x CMOS jumper
1 x COM1 Ring/+5V/+12V selection jumper
1 x Chassis intrusion jumper
1xEmbeddedDisplayPort(eDP)
1xSPIashprogrammableconnector
(continued on the next page)
1-3
Chapter 1: General information

Others
Supported OS Windows
®
7 32-bit
Windows
®
8.1 32-bit / 64-bit
Windows
®
10 64-bit
Linux Fedora
Accessories 1 x SATA cable
1 x SATA power cable
1 x I/O shield
1 x Support DVD
NOTE: Specicationsaresubjecttochangewithoutnotice.
EMB-BSW1
1-4

Chapter 2
Motherboard information
2.1 Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
CAUTION!
• Unplugthepowercordfromthewallsocketbeforetouchingany
component.
• Beforehandlingcomponents,useagroundedwriststraportouchasafely
groundedobjectorametalobject,suchasthepowersupplycase,toavoid
damaging them due to static electricity.
• HoldcomponentsbytheedgestoavoidtouchingtheICsonthem.
• Wheneveryouuninstallanycomponent,placeitonagroundedantistatic
pad or in the bag that came with the component.
• Beforeyouinstallorremoveanycomponent,ensurethatthepowersupply
is switched off or the power cord is detached from the power supply. Failure
todosomaycauseseveredamagetothemotherboard,peripherals,or
components.
Main and Standby Power LEDs
The motherboard comes with one standby power LED and main power LED that
lightuptoindicatethatthesystemisON,insleepmode,orinsoft-offmode.This
is a reminder that you should shut down the system and unplug the power cable
beforeremovingorplugginginanymotherboardcomponent.Theillustrationbelow
shows the location of the onboard LEDs.
EMB-BSW1
EMB-BSW1 Onboard LEDs
LED1
ON
Standby Power Powered Off
OFF
LED2
ON
Main Power Powered Off
OFF
2-1
Chapter 2: Motherboard information

EMB-BSW1
EATX_PWR1
DC_PWR1
USB3_12
LAN1
LAN2
LINE-OUT1
MIC-IN1
CLRTC1
17.0cm(6.7in)
17.0cm(6.7in)
SATA6G_3 SATA6G_2 SATA6G_1
F_PANEL1
ATMODE
CHASSIS1
USB1112 USB910
USBHUB_12
CHA_FAN1
COM4
LED1
LED2
COM1
COM5COM2
COM6COM3
J4
DDR3L DIMM_B1 (64bit, 204-pin module)
DDR3L DIMM_A1 (64bit, 204-pin module)
INV1
J2 J1
J3
DIO1
LVDS1
BOTTOM:EDP1
HDMI
HDMI
SATA_PWR1
KBMS1
ALC
3236
SPK_L1 SPK_R1
SPI1
Intel®
Braswell
Intel®
i211AT
Intel®
i211AT
Super
I/O
AsMedia
1184e
AsMedia
1061
P17C9X
BATTERY1
MINI_CARD1
MINI_CARD2
CH7511
USB3_34
BZ1
653 41 2
16
15
13
14
17
8
7
10
9
11
12
13
202122 19 1823
25
26
224
2.2 Motherboard layout
Place this side towards the rear of
the chassis
NOTE: Place four screws into the holes indicated by circles to secure the
motherboard to the chassis.
CAUTION!Donotovertightenthescrews!Doingsocandamagethe
motherboard.
EMB-BSW1
2-2

Connectors/Jumpers/Slots/LEDs Page
1. EATXpowerconnector(4-pinEATX_PWR1) 2-12
2. USB2.0connectors(10-pinUSBHUB_12,USB9~12) 2-13
3. DDR3LDIMMslots 2-6
4. SPIprogrammingconnector(8-pinSPI1) 2-15
5. Chassisfanconnector(4-pinCHA_FAN1) 2-11
6. Backlightinverterpowerconnector(5-pinINV1) 2-16
7. Inverterbacklightcontrolmodeselection(3-pinJ3) 2-8
8. LVDSpanelvoltageselection(3-pinJ1) 2-7
9. Invertervoltageselection(3-pinJ2) 2-8
10. LVDSconnector(40-pinLVDS1) 2-14
11. Embeddeddisplayport(40-pinEDP1) 2-11
12. MiniCardslots(MINICARD1,MINICARD2) 2-15
13. MainandstandbypowerLEDs(LED1,LED2) 2-1
14. COM1Ring/+5V/+12Vselectionjumper(6-pinJ4) 2-8
15. ATModeselection(3-pinATMODE) 2-9
16. DigitalI/Oconnector(10-pinDIO1) 2-16
17. Systempanelconnector(10-1pinF_PANEL1) 2-12
18. Serialportconnectors(9-pinCOM1~6) 2-17
19. SerialATA6.0Gb/sconnectors(7-pinSATA6G_1~3) 2-13
20. SATApowerconnector(4-pinSATA_PWR1) 2-16
21. ClearRTCRAM(3-pinCLRTC1) 2-7
22. USB3.0connector(20-1pinUSB3_34) 2-14
23. Chassisintrusionjumper(4-1pinCHASSIS1) 2-9
24. Internalaudioconnectors(2-pinSPK_L1,SPK_R1) 2-18
25. PS/2keyboard/mouseconnector(6-pinKBMS1) 2-15
26. IntegratedIntel®BraswellprocessorN3710/N3060 2-6
2-3
Chapter 2: Motherboard information

2.3 Screw size
2.3.1 Component side
EMB-BSW1
2-4

2.3.2 Solder side
2-5
Chapter 2: Motherboard information

2.4 Central Processing Unit (CPU)
ThemotherboardcomeswithanintegratedIntel®BraswellprocessorN3710/
N3060.
2.5 System memory
ThismotherboardcomeswithtwoDoubleDataRate3LowVoltage(DDR3L)
SmallOutlineDualInlineMemoryModules(SO-DIMM)sockets.Thegure
illustratesthelocationoftheDDR3LDIMMsockets:
EMB-BSW1
EMB-BSW1 onboard CPU
Intel®
Braswell
EMB-BSW1
EMB-BSW1 204-pin DDR3L SO-DIMM sockets
DIMM_A1
DIMM_B1
Installing a DIMM
3
To install a DIMM To remove a DIMM
3
EMB-BSW1
2-6

2.6 Jumpers
1. Clear RTC RAM (3-pin CLRTC1)
ThisjumperallowsyoutocleartheRealTimeClock(RTC)RAMin
CMOS.YoucancleartheCMOSmemoryofdate,time,andsystemsetup
parametersbyerasingtheCMOSRTCRAMdata.Theonboardbutton
cellbatterypowerstheRAMdatainCMOS,whichincludesystemsetup
information such as system passwords.
To erase the RTC RAM:
1. TurnOFFthecomputerandunplugthepowercord.
2. Movethejumpercapfrompins1-2(default)topins2-3.Keepthecapon
pins2-3forabout5~10seconds,thenmovethecapbacktopins1-2.
3. PlugthepowercordandturnONthecomputer.
4. Holddownthe<Del>keyduringthebootprocessandenterBIOSsetup
to reenter data.
CAUTION!ExceptwhenclearingtheRTCRAM,neverremovethecapon
CLRTCjumperdefaultposition.Removingthecapwillcausesystemboot
failure!
NOTE:Ifthestepsabovedonothelp,removetheonboardbatteryandmove
thejumperagaintocleartheCMOSRTCRAMdata.AfterclearingtheCMOS,
reinstall the battery.
EMB-BSW1
EMB-BSW1 Clear RTC RAM
1 2 2 3
Protected
(Default)
Clear CMOS
CLRTC1
EMB-BSW1
EMB-BSW1 LVDS Panel Voltage Selection
1 2
2 3
+3V
(Default)
+5V
J1
2. LVDS panel voltage selection (3-pin J1)
Pins
+5V 1-2
+3V(Default) 2-3
2-7
Chapter 2: Motherboard information

3. Inverter voltage selection (3-pin J2)
Pins
+12V 1-2
+5V(Default) 2-3
EMB-BSW1
EMB-BSW1 Inverter Voltage Selection
1 2
2 3
+5V
(Default)
+12V
J2
EMB-BSW1
EMB-BSW1 Mode Selection for Back
Light Control of Inverter
PWM modeDC mode
(Default)
1 2
2 3
J3
EMB-BSW1
EMB-BSW1 COM1 Ring/+5V/+12V Selection
J4
1 2
3 4
5 6
+12V +5V Ring
(Default)
5. COM1 Ring/+5V/+12V selection (6-pin J4)
Pins
+12V 1-2
+5V 3-4
Ring(Default) 5-6
4. Inverter backlight control mode selection (3-pin J3)
Pins
DCmode(Default) 1-2
PWMmode 2-3
EMB-BSW1
2-8

Pins
1-2 Enables the chassis intrusion detection feature
3-4 Disables the chassis intrusion detection feature
(Default)
7. Chassis intrusion jumper (4-1 pin CHASSIS1)
Thisconnectorisforachassis-mountedintrusiondetectionsensororswitch.
Connectoneendofthechassisintrusionsensororswitchcabletothis
connector.Thechassisintrusionsensororswitchsendsahigh-levelsignalto
thisconnectorwhenachassiscomponentisremovedorreplaced.Thesignal
isthengeneratedasachassisintrusionevent.
Movethejumpercaptopins1-2whenyouintendtousethechassisintrusion
detection feature.
EMB-BSW1
EMB-BSW1 Chassis intrusion connector
No Intrudor Intrudor Intrudor
PIN1
CHASSIS1
EMB-BSW1
EMB-BSW1 ATMODE setting
1 2
2 3
ATMODE
AT mode ATX mode
(Default)
6. AT mode selection (3-pin ATMODE)
Pins
AT mode 1-2
ATXmode(Default) 2-3
2-9
Chapter 2: Motherboard information

5. Microphone port (pink). This port connects to a microphone.
6. Line Out port (lime). Thisportconnectstoaheadphoneoraspeaker.Inthe
4-channeland6-channelcongurations,thefunctionofthisportbecomes
FrontSpeakerOut.
2.7 Connectors
2.7.1 Rear panel connectors
LAN port
Speed
LED
Activity
Link LED
ACT/LINK LED SPEED LED
Status Description Status Description
OFF No link OFF 10Mbpsconnection
GREEN Linked ORANGE 100Mbpsconnection
BLINKING Dataactivity GREEN 1Gbpsconnection
1. DC power port.ThisportconnectstoaDCpoweradapter.
2. HDMI ports.TheseportsareforaHigh-DenitionMultimediaInterface
(HDMI)connectors,andareHDCPcompliantallowingplaybackofHDDVD,
Blu-Ray,andotherprotectedcontent.
3. USB 3.0 ports.These9-pinUniversalSerialBus(USB)portsconnectto
USB3.0/2.0devices.
NOTES:
• DONOTconnectakeyboard/mousetoanyUSB3.0portwheninstalling
Windows®operating system.
• DuetoUSB3.0controllerlimitation,USB3.0devicescanonlybeused
underWindows®OSenvironmentandaftertheUSB3.0driverinstallation.
• WestronglyrecommendthatyouconnectUSB3.0devicestoUSB3.0
portsforfasterandbetterperformanceforyourUSB3.0devices.
4. LAN (RJ-45) ports.TheseportsallowGigabitconnectiontoaLocalArea
Network(LAN)throughanetworkhub.RefertothetablebelowfortheLAN
port LED indications.
LAN port LED indications
5321 64
EMB-BSW1
2-10

2.7.2 Internal connectors
CAUTION: DO NOT forget to connect the fan cable to the fan connector.
Insufcientairowinsidethesystemmaydamagethemotherboard
components.Thisisnotajumper!DONOTplaceajumpercaponthefan
connector.
1. Chassis fan connector (4-pin CHA_FAN1)
Connectthefancabletothefanconnectoronthemotherboard,ensuring
that the black wire of each cable matches the ground pin of the connector.
EMB-BSW1
EMB-BSW1 Chassis fan connector
CHA_FAN1
PWM
SENSE
VCC
GND
2. Embedded DisplayPort (40-pin EDP1)
This connector is for an internal embedded DisplayPort connection.
EMB-BSW1
EMB-BSW1 Embedded DisplayPort
EDP1 PIN 1
+V_PANEL
NC
GND
GND
GND
GND
eDP_HPD_R
GND
GND
GND
GND
BKLTEN_R
BKLTCTL_R
NC
NC
+BLVCC
+BLVCC
+BLVCC
+BLVCC
NC
NC
GND
eDP_TXN3_C
eDP_TXP3_C
GND
eDP_TXN2_C
eDP_TXP2_C
GND
eDP_TXN1_C
eDP_TXP1_C
GND
eDP_TXN0_C
eDP_TXP0_C
GND
eDP_AUXP_C
eDP_AUXN_C
GND
+V_PANEL
+V_PANEL
+V_PANEL
PIN 20PIN 40
PIN 21
2-11
Chapter 2: Motherboard information

3. EATX power connector (4-pin EATX_PWR1)
This connector is for EATX power supply plug. The power supply plug
isdesignedtotthisconnectorinonlyoneorientation.Findtheproper
orientationandpushdownrmlyuntiltheconnectorcompletelyt.
4. System panel connector (10-1 pin F_PANEL1)
Thisconnectorsupportsseveralchassis-mountedfunctions.
• SystempowerLED(2-pin+PWR_LED1)
This2-pinconnectorisforthesystempowerLED.Connectthechassis
power LED cable to this connector. The system power LED lights up when
youturnonthesystempower,andblinkswhenthesystemisinsleepmode.
• Hard disk drive activity LED (2-pin +HD_LED-)
This2-pinconnectorisfortheHDDActivityLED.ConnecttheHDDActivity
LEDcabletothisconnector.TheIDELEDlightsuporasheswhendatais
readfromorwrittentotheHDD.
• ATX power button/soft-off button (2-pin PWR_BTN)
This2-pinconnectorisforthesystempowerbutton.
• Reset button (2-pin RESET)
This2-pinconnectorisforthechassis-mountedresetbuttonforsystem
reboot without turning off the system power.
EMB-BSW1
EMB-BSW1 System panel connector
PIN 1
PWR_BTN
GND
PWRBTN#
PWR_LED-
PWR_LED+
(NC)
RSTCON#_PANEL
GND
HDD_LED-
HDD_LED+
F_PANEL1
+PWR_LED-
+HDD_LED- RESET
EMB-BSW1
EMB-BSW1 4-PIN (2x2)
internal power connector
PIN 1
EATX_PWR1
DC_IN DC_IN GND
GND
EMB-BSW1
2-12