Aaeon HSB-965P User manual

Half-size SBC HSB-965P
HSB-965P
Intel® CoreTM 2 Duo Processor
18/24-bit Dual-channel LVDS
Two DDRII 533/667 SODIMM
3 SATA II/ 1 IDE/ 1 FDD/ 1 CompactFlash
7 USB 2.0/ 4 COM/ 1 IrDA
HSB-965P Manual Rev.A 1st Ed.
September 2008

Half-size SBC HSB-965P
i
Copyright Notice
This document is copyrighted, 2008. All rights are reserved. The
original manufacturer reserves the right to make improvements
to the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated,
or transmitted in any form or by any means without the prior
written permission of the original manufacturer. Information
provided in this manual is intended to be accurate and reliable.
However, the original manufacturer assumes no responsibility
for its use, or for any infringements upon the rights of third
parties that may result from its use.
The material in this document is for product information only
and is subject to change without notice. While reasonable
efforts have been made in the preparation of this document to
assure its accuracy, AAEON assumes no liabilities resulting
from errors or omissions in this document, or from the use of the
information contained herein.
AAEON reserves the right to make changes in the product
design without notice to its users.

Half-size SBC HSB-965P
ii
Acknowledgments
All other products’ name or trademarks are properties of their
respective owners.
 Award is a trademark of Award Software International, Inc.
 CompactFlash™ is a trademark of the Compact Flash
Association.
 Intel®, Core 2 Duo™ are trademarks of Intel®Corporation.
 Microsoft Windows®is a registered trademark of Microsoft Corp.
 ITE is a trademark of Integrated Technology Express, Inc.
 IBM, PC/AT, PS/2, and VGA are trademarks of International
Business Machines Corporation.
 SoundBlaster is a trademark of Creative Labs, Inc.
All other product names or trademarks are properties of their
respective owners.

Half-size SBC HSB-965P
iii
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 1 HSB-965P CPU Card
• 1 Floppy Cable
• 1 ATA-100 Cable
• 1 USB Cable
• 1 Keyboard Cable
• 1 Serial + Parallel Cable
• 3 Serial Cables
• 3 SATA Cables
• 1 ATX Cable
• 1 Heat Sink
• 1 CPU Cooler Fan
• 1 Quick Installation Guide
• 1 CD-ROM for manual (in PDF format) and drivers
If any of these items should be missing or damaged, please
contact your distributor or sales representative immediately.

Half-size SBC HSB-965P
iv
Contents
Chapter 1 General Information
1.1 Introduction................................................................1-2
1.2 Features....................................................................1-3
1.3 Specifications............................................................1-4
Chapter 2 Quick Installation Guide
2.1 Safety Precautions....................................................2-2
2.2 Location of Connectors and Jumpers .......................2-3
2.3 Mechanical Drawing..................................................2-5
2.4 List of Jumpers..........................................................2-7
2.5 List of Connectors .....................................................2-8
2.6 Setting Jumpers ........................................................2-10
2.7 CF Voltage 3.3V/5V Selection (JP1).........................2-11
2.8 Clear CMOS (CMOS1)..............................................2-11
2.9 LVDS Power Selection (JP4) .................................... 2-11
2.10 LVDS Inverter Voltage Selection (JP5)...................2-11
2.11 Front Panel Connector (FP1).................................. 2-11
2.12 Front Panel Connector (FP2).................................. 2-12
2.13 RS-232 Serial Prot Connector (COM1, COM3, COM4)
.........................................................................................2-12
2.14 RS-232/422/485 Serial Port Connector (COM2).....2-12
2.15 LPT Port Connector (LPT1) ....................................2-12
2.16 ATX Power Control Connector with BP (CN 2).......2-13
2.17 IrDA Connector (CN3).............................................2-13

Half-size SBC HSB-965P
v
2.18 Digital I/O (CN4)......................................................2-14
2.19 USB Connector (CN5-7) .........................................2-14
2.20 LVDS (CN8) ............................................................2-14
2.21 FAN Connector (CN9).............................................2-15
2.22 Audio Pin Header (CN10) .......................................2-15
2.23 Internal Keyboard Connector (CN11)......................2-15
2.24 PS/2 Keyboard/Mouse Connector (CN12)..............2-16
2.25 LVDS Inverter (CN13).............................................2-16
Chapter 3 Award BIOS Setup
3.1 System Test and Initialization. ..................................3-2
3.2 Award BIOS Setup....................................................3-3
Chapter 4 Driver Installation
4.1 Installation.................................................................4-3
Appendix A Programming The Watchdog Timer
A.1 Programming .........................................................A-2
A.2 ITE8712 Watchdog Timer Initial Program..............A-5
Appendix B I/O Information
B.1 I/O Address Map....................................................B-2
B.2 1st MB Memory Address Map ................................B-3
B.3 IRQ Mapping Chart................................................B-4
B.4 DMA Channel Assignments .................................B-4
Appendix C Mating Connector
C.1 List of Mating Connectors and Cables.................. C-2

Half-size SBC HSB-965P
Chapter 1 General Information 1- 1
General
Chapter
1
Information

Half-size SBC HSB-965P
Chapter 1 General Information 1- 2
1.1 Introduction
The HSB-965P supports Intel®Socket 478-based Core 2 Duo
processor by utilizing the Intel®GME965 + ICH8-M chipset.
Moreover it equips two DDRII SODIMM and supports DDRII
533/667 up to 4GB. This model accommodates two Gigabit
Ethernet RJ-45 connectors (10/100 Base-TX and Gigabit Ethernet
optional) that are controlled by one Intel®82562/82566 (co-lay,
optional) and Intel 82574L. This configuration allows for fast
network connections and multi-task data transmission on the
network.
The LCD controller is integrated on Intel®82855GME that support
dual displays support to meet the demands of the embedded
market while still maintaining cost efficiency. In addition, HSB-965P
deploys 7 USB2.0, 4 COMs (3 RS-232 and 1 RS-232/422/485), one
parallel port, one IrDA, and digital I/O for a flexible I/O selection.
The storage of HSB-965P supports three SATA II ports and one
Type II CompactFlash.
The HSB-965P provides an ideal combination of high performance,
widely expandable interfaces and compact size for applications that
have space limitations. It will be an ideal tool for your vital
applications.

Half-size SBC HSB-965P
Chapter 1 General Information 1- 3
1.2 Features
 Intel®CoreTM 2 Duo Processor, FSB 533/667/800MHz
 Two SODIMM Dual-channel DDRII 533/667 Memory,
up to 4GB
 Up to 18/24-bit Dual-channel LVDS
 Integrated Intel®Enhance Graphics Core, VGA Support
 Two Gigabit Ethernet (Optional 10/100Base-TX and
Gigabit Ethernet)
 Three SATA II ports and one Type II CompactFlash
 Seven USB2.0/ 1 RS-232/422/485 & 3 RS-232/ 1
Parallel/ 1 IrDA/ Digital I/O

Half-size SBC HSB-965P
Chapter 1 General Information 1- 4
1.3 Specifications
System
 CPU Intel® Socket 478-based CoreTM 2
Duo Processor, FSB 533/667/
800MHz
 System Memory Two DDRII SODIMM, support
DDRII 533/667 up to 4GB
 Chipset Intel® GME965 + Intel®ICH8-M
 Ethernet LAN1: Intel®82574L
LAN2: Intel®82566/ 82562 (co-lay,
optional)
One PCI-Express, 10/100Base-TX
& Gigabit Ethernet optional, RJ-45
x 2
 BIOS Award Plug & Play SPI BIOS –
8Mb ROM
 Watchdog Timer 1~255 steps, can be set with
software on Super I/O
 CompactFlash Supports CFD Type II Connector,
shared IDE channel (Master)
 Expansion Interface PICMG/ PCI Interface
 Battery Lithium battery
 Power Requirement ATX +12V, 4-pin power connector
 Board Size 7.28”(L) x 4.8” (W)

Half-size SBC HSB-965P
Chapter 1 General Information 1- 5
(185mm x 122mm)
 Gross Weight 0.88lb (0.4kg)
 Operating Temperature 32oF~140oF(0oC~60oC)
 EMC CE/FCCClassA
Display
 VGA Controller Enhanced Integrated Graphics
 LCD Controller Integrated on Intel®82855GME,
LVDS output, dual display
support
I/O
 Storage SATA II x 2 (onboard), IDE slot x 1
(Shared), Standard Floppy Disk
Drive x 1 (supports up to one
floppy device)
 IrDA One IrDA Tx/Rx header
 Audio MIC-in/ Line-in/ Line-out/ CD-in
(Optional Daughter Board)
 Parallel Port Supports SPP/EPP/ECP mode
 USB Seven USB 2.0 Ports, Three 5x2
pin headers for internal, One
Type-A connector onboard
 RTC Internal RTC
 Serial Port COM port x 4 (Internal pin header

Half-size SBC HSB-965P
Chapter 1 General Information 1- 6
x 4)
RS-232 x 3, RS-232/422/485 x 1
 Keyboard & Mouse One Mini-DIN PS/2 keyboard and
mouse connector, one internal
Keyboard pin header

Half-size SBC HSB-965P
Chapter 2 Quick Installation Guide 2-1
Quick
Installation
Chapter
2
Guide
Notice:
The Quick Installation Guide is derive
d
f
rom Chapter 2 of user manual. For othe
r
chapters and further installation
instructions, please refer to the use
r
manual CD-ROM that came with th
e
p
roduct.
Part No. 2007965P10 Printed in Taiwan September 2008

Half-size SBC HSB-965P
Chapter 2 Quick Installation Guide 2 - 2
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis

Half-size SBC HSB-965P
Chapter2QuickInstallationGuide2 - 3
2.2 Location of Connectors and Jumpers
Component Side

Half-size SBC HSB-965P
Solder Side
Chapter 2 Quick Installation Guide 2 - 4

Half-size SBC HSB-965P
Chapter2QuickInstallationGuide2 - 5
2.3 Mechanical Drawing
Component Side

Half-size SBC HSB-965P
Chapter 2 Quick Installation Guide 2 - 6
Solder Side

Half-size SBC HSB-965P
Chapter2QuickInstallationGuide2 - 7
2.4 List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Jumpers
Label Function
JP1 CFD Voltage 3.3V/5V Selection
CMOS1 Clear CMOS
JP4 LVDS Power Selection
JP5 LVDS Inverter Power Selection

Half-size SBC HSB-965P
Chapter 2 Quick Installation Guide 2 - 8
2.5 List of Connectors
The board has a number of connectors that allow you to configure your
system to suit your application. The table below shows the function of
each board's connectors:
Connectors
Label Function
FP1 Front Panel Connector 1
FP2 Front Panel Connector 2
VGA1 VGA Display Connector
FDD1 Floppy Connector
IDE1 IDE Connector (Slave)
CFD1 Compact Flash Slot (Master)
COM1, COM3,
COM4 RS-232 Serial Port Connector
COM2 RS-232/422/485 Serial Port Connector
LPT1 LPT Port Connector
USB1 USB Connector
LAN1~2 10/100 or 100/1000 Base-TX Ethernet
Connector ( LAN2 optional)
DIMM1~2 DDRII SODIMM Slot
ATX1 +12V Power Connector
ATX2 ATX Power Connector
CN2 ATX Power Control Connector
CN3 IrDA Connector
CN4 Digital I/O Connector
CN5~7 USB Pin Header