Abb Coriolismaster fcb400 User manual

—

ABB MEASUREMENT & ANALYTICS | COMMISSIONING INSTRUCTION | CI/FCB400/FCH400-EN REV. H

CoriolisMaster FCB400, FCH400

Coriolis mass flowmeter

—

ABB Measurement & Analytics

For your local ABB contact, visit:

www.abb.com/contacts

For more product information, visit:

www.abb.com/flow

Device firmware version: 01.08.00

Measurement made easy

CI/FCB400/FCH400-EN Rev. H 07.2021

—

CoriolisMaster FCB430 / 450

CoriolisMaster FCH430 / 450

Introduction

With no up or downstream piping requirements

the compact Coriolis flowmeters can be installed

in the tightest spaces, enabling applications not

possible before.

CoriolisMaster FCB400

The compact Coriolis mass flowmeters from the

CoriolisMaster FCB400 series offer low pressure

drop, high capacity, an intuitive ABB display

featuring a standardized design and cross-

product compatibility, five modular inputs and

outputs as well as HART communication.

CoriolisMaster FCH400

The compact Coriolis mass flowmeters for

hygienic applications from the CoriolisMaster

FCH400 series additionally offer EHEDG certified

cleanability; all wetted materials are polished.

Additional Information

Additional documentation on CoriolisMaster

FCB400, FCH400 is available for download free of

charge at www.abb.com/flow.

Alternatively simply scan this code:

—

We reserve the right to make technical changes or modify the contents of this document

without prior notice. With regard to purchase orders, the agreed particulars shall prevail.

ABB does not accept any responsibility whatsoever for potential errors or possible lack of

information in this document.

We reserve all rights in this document and in the subject matter and illustrations contained

therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole

or in parts – is forbidden without prior written consent of ABB.

2 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

Table of contents

1Safety..........................................................................4

General information and instructions..................................4

Warnings....................................................................................4

Intended use .............................................................................5

Improper use.............................................................................5

Notes on data safety ...............................................................5

Warranty provisions.................................................................5

Manufacturer’s address..........................................................5

2Use in potentially explosive atmospheres .............6

Device overview ........................................................................6

ATEX / IECEx ........................................................................6

cFMus .................................................................................... 7

Ex marking.................................................................................8

Description of model numbers.........................................8

ATEX / IECEx ...................................................................... 11

cFMus .................................................................................. 12

Temperature data .................................................................. 13

Temperature resistance for the connecting cable...... 13

Environmental and process conditions for model

FCx4xx… ............................................................................. 13

Measuring medium temperature for sensors in

integral mount design with dual-compartment

housing................................................................................14

Measuring medium temperature for sensors in

integral mount design with single-compartment

housing................................................................................ 15

Measuring medium temperature for sensors in remote

mount design..................................................................... 16

Electrical data ......................................................................... 17

Overview ............................................................................. 17

Zone 2, 21 and Division 2 – Model: FCx4xx-A2, FCx4xx-

F2.......................................................................................... 18

Zone 1 ,21 und Division 1 – Model: FCx4xx-A1, FCx4xx-

F1 ..........................................................................................20

Special connection conditions........................................22

Installation instructions........................................................23

ATEX / IECEx ......................................................................23

cFMus ..................................................................................23

Use in areas exposed to combustible dust ..................23

Opening and closing the housing ..................................23

Cable entries in accordance with ATEX / IECEx...........24

Cable entries in accordance with cFMus.......................24

Electrical connections ......................................................25

Process sealing ..................................................................25

Operating instructions..........................................................26

Protection against electrostatic discharges................26

Repair...................................................................................26

Changing the type of protection....................................26

3Product identification ............................................ 27

Name plate ..............................................................................27

4Transport and storage............................................28

Inspection................................................................................28

Transporting the device........................................................28

Storing the device.................................................................. 29

Ambient conditions.......................................................... 29

Returning devices .................................................................. 29

5Installation............................................................... 29

General installation conditions ........................................... 29

Installation location and assembly................................ 29

Liquid measuring media..................................................30

Gaseous measuring media...............................................31

Turn-off devices for the zero point adjustment ......... 32

Sensor insulation .............................................................. 32

Installation in EHEDG-compliant installations............ 32

Devices for legal metrology ............................................ 33

Process conditions ................................................................ 33

Temperature limits °C (°F) .............................................. 33

Temperature Data ............................................................ 33

Pressure ratings ................................................................ 33

Housing as a protective device (optional) ................... 34

Material load for process connections .............................. 34

Material load curves for flange devices ........................ 34

Installing the sensor.............................................................. 35

Installing the transmitter in the remote mount design . 35

Opening and closing the housing....................................... 37

Dual- compartment housing........................................... 37

Single-compartment housing......................................... 38

Adjusting the transmitter position .................................... 38

Installing the plug-in cards ..................................................40

Dual-compartment housing............................................ 42

Single-compartment housing......................................... 43

Ethernet card.....................................................................44

6Electrical connections ............................................ 45

Safety instructions ................................................................45

Power supply ..........................................................................45

Installing the connection cables .........................................46

Recommended cables...................................................... 46

Terminal assignment ............................................................ 47

Electrical data for inputs and outputs...............................48

Connection examples....................................................... 53

Connection to integral mount design................................ 56

Connection to remote mount design ................................ 58

Digital communication ......................................................... 61

HART® Communication.................................................... 61

Modbus® communication ............................................... 61

Cable specification........................................................... 62

PROFIBUS DP® communication...................................... 62

EtherNet/IP™ communication ....................................... 63

Ethernet communication ................................................64

Connect the retractable plug to the Ethernet card....66

7Commissioning ........................................................71

Safety instructions .................................................................71

Hardware settings..................................................................71

Dual- compartment housing............................................71

Single-compartment housing......................................... 72

Configuration of digital outputs V1 / V2 or V3 / V4 ... 72

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 3

Checks prior to commissioning ..........................................73

Switching on the power supply ........................................... 73

Parameterization of the device ...........................................73

Installation of ABB AssetVision Basic and ABB Field

Information Manager (FIM) .............................................73

Parameterization via the infrared service port adapter

..............................................................................................75

Parameterization via HART®............................................76

Basic Setup.............................................................................. 77

Menu: Easy Setup .............................................................. 77

8Operation ................................................................. 81

Safety instructions.................................................................81

Menu navigation.....................................................................81

Menu levels ..............................................................................82

Selecting and changing parameters...................................83

Entry from table.................................................................83

Error messages on the LCD display................................... 84

9Maintenance / Repair..............................................85

Safety instructions.................................................................85

10Dismounting and disposal......................................85

Dismounting ...........................................................................85

Disposal .................................................................................. 86

11Specification ............................................................86

12Additional documents ............................................86

13Appendix................................................................... 87

Return form .............................................................................87

4 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

1Safety

General information and instructions

These instructions are an important part of the product and

must be retained for future reference.

Installation, commissioning, and maintenance of the product

may only be performed by trained specialist personnel who have

been authorized by the plant operator accordingly. The specialist

personnel must have read and understood the manual and must

comply with its instructions.

For additional information or if specific problems occur that are

not discussed in these instructions, contact the manufacturer.

The content of these instructions is neither part of nor an

amendment to any previous or existing agreement, promise or

legal relationship.

Modifications and repairs to the product may only be performed

if expressly permitted by these instructions.

Information and symbols on the product must be observed.

These may not be removed and must be fully legible at all times.

The operating company must strictly observe the applicable

national regulations relating to the installation, function testing,

repair and maintenance of electrical products.

Warnings

The warnings in these instructions are structured as follows:

DANGER

The signal word ‘DANGER’ indicates an imminent danger.

Failure to observe this information will result in death or

severe injury.

WARNING

The signal word ‘WARNING’ indicates an imminent danger.

Failure to observe this information may result in death or

severe injury.

CAUTION

The signal word ‘CAUTION’ indicates an imminent danger.

Failure to observe this information may result in minor or

moderate injury.

NOTICE

The signal word

‘

NOTIC

’

indicates possible material damage.

Note

‘Note’ indicates useful or important information about the

product.

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 5

Intended use

This device is intended for the following uses:

• To convey liquids and gases (including unstable measuring

media).

• To meter mass flow directly.

• To meter volumetric flow (indirectly via mass flow and

density).

• To measure the density of the measuring medium.

• To measure the temperature of the measuring medium.

The device has been designed for use exclusively within the

technical limit values indicated on the identification plate and in

the data sheets.

When using measuring media, the following points must be

observed:

• Measuring media may only be used if, based on the state

of the art or the operating experience of the user, it can

be assured that the chemical and physical properties

necessary for operational security of the materials of the

wetted parts of the flowmeter sensor will not be

adversely affected during the operating time.

• Media containing chloride in particular can cause

corrosion damage to stainless steels which, although not

visible externally, can damage wetted parts beyond repair

and lead to the measuring medium escaping. It is the

operator's responsibility to check the suitability of these

materials for the respective application.

• Measuring media with unknown properties or abrasive

measuring media may only be used if the operator is able

to perform regular and suitable tests to ensure the safe

condition of the device

Improper use

The following are considered to be instances of especially

improper use of the device:

• Operation as a flexible compensating adapter in piping,

for example for compensating pipe offsets, pipe

vibrations, pipe expansions, etc.

• For use as a climbing aid, for example for mounting

purposes.

• For use as a bracket for external loads, for example as a

support for piping, etc.

• Material application, for example by painting over the

housing, name plate or welding/soldering on parts.

• Material removal, for example by spot drilling the

housing.

Notes on data safety

This product is designed to be connected to and to

communicate information and data via a network interface.

It is operator’s sole responsibility to provide and continuously

ensure a secure connection between the product and your

network or any other network (as the case may be).

Operator shall establish and maintain any appropriate measures

(such as but not limited to the installation of firewalls,

application of authentication measures, encryption of data,

installation of anti-virus programs, etc.) to protect the product,

the network, its system and the interface against any kind of

security breaches, unauthorized access, interference, intrusion,

leakage and / or theft of data or information.

ABB Ltd and its affiliates are not liable for damages and / or

losses related to such security breaches, any unauthorized

access, interference, intrusion, leakage and / or theft of data or

information.

Warranty provisions

Using the device in a manner that does not fall within the scope

of its intended use, disregarding this manual, using

underqualified personnel, or making unauthorized alterations

releases the manufacturer from liability for any resulting

damage. This renders the manufacturer's warranty null and void.

Manufacturer’s address

ABB Automation Products GmbH

Measurement & Analytics

Schillerstr. 72

32425 Minden

Germany

Tel: +49 571 830-0

Fax: +49 571 830-1806

Customer service center

Tel: +49 180 5 222 580

Email: [email protected]

6 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

2Use in potentially explosive atmospheres

Note

Further information on the Ex-Approval of devices can be found in the type examination certificates or the relevant certificates at

www.abb.com/flow .

Device overview

ATEX / IECEx

Standard / No explosion protection Zone 2, 21, 22 Zone 1, 21 (Zone 0)

Model number FCx4xx Y0 FCx4xx A2 FCx4xx A1

Integral mount design

• Standard

• Zone 2, 21, 22

• Zone 1, 21

• Zone 0

Model number FCT4xx Y0 FCx4xx Y0 FCT4xx A2 FCx4xx A2 FCT4xx A1 FCx4xx A1

Remote mount design

Transmitter and

flowmeter sensor

• Standard

• Zone 2, 21, 22

• Zone 1, 21

• Zone 0

Model number FCT4xx Y0 FCT4xx A2 FCx4xx A1

Remote mount design

Transmitter

• Standard

• Zone 2, 21, 22

Sensor

• Zone 1, 21

• Zone 0

Model number — FCT4xx A2 FCx4xx A1

Remote mount design

Transmitter

• Zone 2, 21, 22

Sensor

• Zone 1, 21

—

1 Single-compartment housing

2 Dual-compartment housing

3Zone 0 within the meter tube

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 7

cFMus

Standard / No explosion protection Class I Div. 2 / Zone 2 Class I Div. 1 / Zone 1 (Zone 0)

Model number FCx4xx Y0 FCx4xx F2 FCx4xx F1

Integral mount design

• Standard

• Div. 2 / Zone 2

• Div. 1 / Zone 1

(Zone 0)

Model number FCT4xx Y0 FCx4xx Y0 FCT4xx F2 FCx4xx F2 FCT4xx F1 FCx4xx F1

Remote mount design

Transmitter and

flowmeter sensor

• Div. 2 / Zone 2

• Div. 1 / Zone 1

(Zone 0)

Model number FCT4xx Y0 FCT4xx F2 FCx4xx F1

Remote mount design

Transmitter

• Standard

Sensor

• Div. 2 / Zone 2

• Div. 1 / Zone 1

(Zone 0)

Model number — FCT4xx F2 FCx4xx F1

Remote mount design

Transmitter

• Div. 2 / Zone 2

Sensor

• Div. 1 / Zone 1

(Zone 0)

—

1 Single-compartment housing

2 Dual-compartment housing

3Zone 0 within the meter tube

8 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

… 2 Use in potentially explosive atmospheres

Ex marking

Description of model numbers

Each device design has a specific model number. The parts of the model number relating to explosion protection are listed in the

following table. The complete key to model numbers is described in the device data sheet.

Basic model FCa4c d m f g h i j k l m

Explosion protection

Without Y0

ATEX / IECEx (Zone 2 / 22) A2

ATEX / IECEx (Zone 1 / 21) A1

cFMus version, Class 1, Div. 2 (Zone 2 / 21) F2

cFMus version, Class 1, Div. 1 (Zone 1 / 21) F1

NEPSI (Zone 2 / 22) S2

NEPSI (Zone 1 / 21) S1

Design / terminal box material / cable glands

Integral mount - see transmitter housing Y0

Remote mount / aluminum / 1 × M20 × 1.5 U1

Remote mount / aluminum / 1 × NPT ½ in U2

Remote mount / stainless steel / 1 × M20 × 1.5 A1

Remote mount / stainless steel / 1 × NPT ½ in A2

Nominal diameter / nominal connection diameter xxxxx

Process connection xx

Material for wetted parts

Stainless steel A1

Polished stainless steel H1

Nickel alloy C1

Flow rate calibration x

Density calibration x

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 9

Basic model FCa4c d m f g h i j k l m

Design / transmitter housing / transmitter housing material / cable gland

Integral mount / dual-compartment housing / aluminum / 3 × M20 × 1.5 D1

Integral mount / dual-compartment housing / aluminum / 3 × NPT ½ in D2

Integral mount / dual-compartment housing / aluminum / 3 × M20 × 1.5 (Ex d / XP) D5

Integral mount / dual-compartment housing / aluminum / 3 × NPT ½ in (Ex d / XP) D6

Integral mount / dual-compartment housing / stainless steel / 3 × M20 × 1.5 D3

Integral mount / dual-compartment housing / stainless steel / 3 × NPT ½ in D4

Integral mount / dual-compartment housing / stainless steel / 3 × M20 × 1.5 (Ex d / XP) D7

Integral mount / dual-compartment housing / stainless steel / 3 × NPT ½ in (Ex d / XP) D8

Integral mount / single-compartment housing / aluminum / 3 × M20 × 1.5 S1

Integral mount / single-compartment housing / aluminum / 3 × NPT ½ in S2

Remote mount / dual-compartment housing / aluminum / 3 × M20 × 1.5 R1

Remote mount / dual-compartment housing / aluminum / 3 × NPT ½ in R2

Remote mount / dual-compartment housing / aluminum / 3 × M20 × 1.5 (Ex d / XP) R5

Remote mount / dual-compartment housing / aluminum / 3 × NPT ½ in (Ex d / XP) R6

Remote mount / dual-compartment housing / stainless steel / 3 × M20 × 1.5 R3

Remote mount / dual-compartment housing / stainless steel / 3 × NPT ½ in R4

Remote mount / dual-compartment housing / stainless steel / 3 × M20 × 1.5 (Ex d / XP) R7

Remote mount / dual-compartment housing / stainless steel / 3 × NPT ½ in (Ex d / XP) R8

Remote mount / single-compartment housing, wall mounting / aluminum / 4 × M20 × 1.5 W1

Remote mount / single-compartment housing, wall mounting / aluminum / 4 × NPT ½ in W2

Remote mount / not specified Y0

Outputs

Current output 1 (active or passive), digital output 1 & 2 (passive),

HART®, PROFIBUS DP®

Current output 1 (active), digital output 1 & 2 (passive), HART®, Modbus® M1*

Current output 1 (active / passive), digital output 1 & 2 (passive), digital output 3

(active), HART, Modbus

Current output 1 (active / passive), digital output 1 & 2 (passive), HART®,

1 Port Ethernet

E2**

Current output 1 (active / passive), digital output 1 & 2 (passive), HART®,

2 Port Ethernet

E3**

Current output 1 (active / passive), digital output 1 & 2 (passive), HART®,

1 Port Ethernet + POE

E4**

Current output 1 (active / passive), digital output 1 & 2 (passive), HART G0

Current output 1 (active / passive), digital output 1 & 2 (passive),

24 V DC transmitter loop power supply, HART®

Current output 1 (active / passive), digital output 1 & 2 (passive),

current output 2 (passive), HART®

Current output 1 (active / passive), digital output 1 & 2 (passive),

current output 2 (passive), current output 3 (passive), HART®

Current output 1 (active / passive), digital output 1 & 2 (passive),

current output 2 (passive), 24 V DC transmitter loop power supply, HART®

Without Y0

Power supply

100 to 230 V AC A

11 to 30 V DC C

Without Y

* The M1 design is identical in construction to the M5 design, as it can also be called in other locations

** Only available with single-compartment housing, non-Ex or Zone 2, Division 2

10 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

… 2 Use in potentially explosive atmospheres

… Ex marking

Additional ordering information FCa4cdefghijklm XXX XXX XX

Option card 1

2 port Ethernet (various protocols) DR6*

1 × active digital output DRH

Option card 2

Power over Ethernet module / Modbus DS8*

1 × active digital output DSH

Connection type

Without U0

1 × M 12 plug connector for Ethernet 1 Port (4 signal lines) UE*

2 × M 12 plug connector for Ethernet 2 Port (4 signal lines) UF*

1 × M 12 plug connector for Ethernet 1 Port (8 signal lines) UG*

1 × RJ45 connector with 5 m cable length attached (4 signal lines) U5*

2 × RJ45 connector with 5 m cable length attached (4 signal lines) UB*

1 × RJ45 connector with 5 m cable length attached (8 signal lines) UC*

1 × RJ45 connector with 10 m cable length attached (4 signal lines) U6*

2 × RJ45 connector with 10 m cable length attached (4 signal lines) DU*

1 × RJ45 connector with 10 m cable length attached (8 signal lines) UH*

1 × RJ45 connector with 15 m cable length attached (4 signal lines) U7*

2 × RJ45 connector with 15 m cable length attached (4 signal lines) UJ*

1 × RJ45 connector with 15 m cable length attached (8 signal lines) UK*

1 × RJ45 connector with 20 m cable length attached (4 signal lines) U8*

2 × RJ45 connector with 20 m cable length attached (4 signal lines) UN*

1 × RJ45 connector with 20 m cable length attached (8 signal lines) UP*

* Only available with single-compartment housing and Ethernet

DANGER

Risk of injury caused by live parts!

When using the outputs of the M6 option digital output or the DRH/DSH option active digital output option cards, all the option

cards used and all pre-installed output circuits must use the ‘Increased safety’ (Ex-e) IP rating.

The ‘Intrinsic safety’ (Ex i) IP rating is not permitted.

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 11

ATEX / IECEx

Note

• A specific marking applies, depending on the design.

• ABB reserves the right to modify the Ex-marking. Refer to the name plate for the exact marking.

Model number for use in Zone 2, 21 Ex marking Certificate

FCa4c – A2Y0fghijD

Integral mount design with dual-compartment housing

II3G Ex ec IIC T6...T1 Gc

II2D Ex tb IIIC T80°C...Tmedium Db

ATEX:

FM15ATEX0014X, FM15ATEX0016X

IECEx:

IECEx FME 15.0005X

FCa4c – A2efghijY

Sensor in remote mount design with dual-compartment

housing

FCT4c – A2R

Transmitter in remote mount design with dual-

compartment housing

II3G Ex ec IIC T6 Gc

II2D Ex tb IIIC T80°C Db

Model number for use in Zone 1, 21 Ex marking Certificate

FCa4c – A1Y0fghijDx (x = 1 to 4)

Integral mount design with dual-compartment housing

II 1/2 (1) G Ex db eb ia mb [ia Ga] IIC T6…T1 Gb

II 2 (1) D Ex ia tb [ia Da] IIIC T80°C Db

ATEX:

FM15ATEX0015X

IECEx:

IECEx FME 15.0005X

FCa4c – A1Y0fghijDx (x = 5 to 8)

Integral mount design with dual-compartment housing

(flameproof enclosure ‘Ex d’)

II 1/2 (1) G Ex db ia mb [ia Ga] IIB+H2 T6...T1 Gb

II 2 (1) D Ex ia tb [ia Da] IIIC T80°C Db

FCa4cA1Y0fghM6jDx (x=1 to 4) or DRH or DSH option

card

Integral mount design with dual-compartment housing

and active digital output option card

II 1/2 (1) G Ex db eb ia mb IIC T6…T1 Gb

II 2 (1) D Ex eb tb IIIC T80°C Db

FCa4c – A1efghijY

Sensor in remote mount design with dual-compartment

housing

II 1/2 G Ex eb ia mb IIB+H2 T6…T1 Ga/Gb

II 2 D Ex ia tb IIIC T80°C Db

FCa4cA1Y0fghM6jDx (x=5 to 8) or DRH or DSH option

card

Integral mount design with dual-compartment housing

(flameproof enclosure ‘Ex d’) and active digital output

option card

II 1/2 (1) G Ex db ia mb IIB+H2 T6...T1 Gb

II 2 (1) D Ex ia tb IIIC T80°C Db

FCT4c – A1R (x = 1 to 4)

Transmitter in remote mount design with dual-

compartment housing

II 2 (1) G Ex db e ia mb [ia Ga] IIC T6…T1 Gb

II 2 (1) D Ex ia mb tb [ia Da] IIIC T80°C Db

FCT4c – A1R (x = 5 to 8)

Transmitter in remote mount design with dual-

compartment housing

(flameproof enclosure ‘Ex d’)

II 2 (1) G Ex db ia mb [ia Ga] IIB+H2 T6…T1 Gb

II 2 (1) D Ex ia tb [ia Da] IIIC T80°C Db

FCT4c – A1R (x = 1 to 4) fghM6 or DRH or DSH option

card

Transmitter in remote mount design with dual-

compartment housing and active digital output option

card

II 2 (1) G Ex db eb ia mb IIC T6…T1 Gb

II 2 (1) D Ex ia mb tb IIIC T80°C Db

FCT4c – A1R (x = 5 to 8)fghM6 or DRH or DSH option

card

Transmitter in remote mount design with dual-

compartment housing (flameproof enclosure ‘Ex d’) and

active digital output option card

II 2 (1) G Ex db ia mb IIB+H2 T6…T1 Gb

II 2 (1) D Ex ia tb IIIC T80°C Db

12 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

… 2 Use in potentially explosive atmospheres

… Ex marking

cFMus

Note

• A specific marking applies, depending on the design.

• ABB reserves the right to modify the Ex-marking. Refer to the name plate for the exact marking.

Model number for use in Division 2 Ex marking

FCa4c – F2Y0fghijD

Integral mount design with dual-compartment housing

Certificate: FM18US0160X

NI: CL I,II,III Div 2, GPS ABCDEFG, T6…T1

CL I, ZN 2, AEx ec IIC T6…T1

CL I, ZN 2, Ex ec IIC T6...T1

See handbook for temperature class

information

Certificate: FM18CA0073X

DIP: CL II,III, Div 1, GPS EFG, T6

ZN 21, AEx ia tb IIIC T80°C

ZN21,Ex ia tb IIIC T80°C

FCa4c – F2efghijY

Sensor in remote mount design with dual-compartment housing

Design in accordance with ANSI / ISA 12.27.01 as ‘Single Seal Device’

or as ‘Dual Seal Device’ (option TE2)

FCT4c – F2R

Transmitter in remote mount design with dual-compartment housing

FCT4c – F2W

Transmitter in remote mount design with single-compartment

housing

Model number for use in Division 1 Ex marking Certificate

FCa4c – F1Y0fghijDx (x = 1 to 4)

Integral mount design with dual-compartment housing

XP-IS: CL I, Div 1, GPS ABCD,T6…T1 (USA)

XP-IS: CL I, Div 1, GPS BCD,T6…T1 (CAN)

DIP: CL II,III, Div 1, GPS EFG,T6

CL I, ZN 1, AEx db ia IIB+H2 T6…T1 (USA)

ZN21, AEx ia tb IIIC T80°C (USA)

CL I, ZN 1, Ex db ia IIB+H2 T6…T1 (CAN)

ZN21, Ex ia tb IIIC T80°C (CAN)

See handbook for temperature class information and installation

drawing 3KXF000028G0009

cFMus:

3050239

FCa4c – F1Y0fghijDx (x = 5 to 8)

Integral mount design with dual-compartment housing

(Explosionproof ‘XP’).

Design in accordance with ANSI / ISA 12.27.01 as ‘Single Seal Device’

or as ‘Dual Seal Device’ (option TE2)

FCa4c – F1efghijY

Sensor in remote mount design with dual-compartment housing

XP-IS: CL I, Div 1, GPS BCD T6…T1 (USA)

DIP: CL II,III, Div 1, GPS EFG,T6

CL I, ZN 1, AEx db ia IIB+H2 T6…T1 (USA)

ZN 21, AEx ia tb IIIC T80°C (USA)

CL I, ZN 1, Ex db ia IIB+H2 T6…T1 (CAN)

ZN21, Ex ia tb IIIC T80°C (CAN)

See handbook for temperature class information and installation

drawing 3KXF000028G0009

Design in accordance with ANSI / ISA 12.27.01 as ‘Single Seal Device’

or as ‘Dual Seal Device’ (option TE2)

FCT4c – F1Rx (x = 1 to 4)

Transmitter in remote mount design with dual-compartment housing

XP-IS: CL I, Div 1, GPS BCD,T6…T1 (USA) XP-IS: CL I, Div 1, GPS

BCD,T6…T1 (CAN)

DIP: CL II,III, Div 1, GPS EFG, T6

CL I, ZN 1, AEx db ia IIB+H2 T6…T1 (USA)

ZN 21, AEx ia tb IIIC T80°C (USA)

CL I, ZN 1, Ex db ia IIB+H2 T6…T1 (CAN)

ZN21,Ex ia tb IIIC T80°C (CAN)

See handbook for temperature class information and installation

drawing 3KXF000028G0009

FCT4c – F1Rx (x = 5 to 8)

Sensor in remote mount design with dual-compartment housing

(Explosionproof ‘XP’).

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 13

Temperature data

Temperature resistance for the connecting cable

The temperature at the cable entries of the device depends on

the design, the measuring medium temperature Tmedium and the

ambient temperature Tamb..

For the electric connection of the device, use only cables with

sufficient temperature resistance in accordance with the

following table.

Devices in integral mount design with dual-compartment

housing

Tamb. Temperature resistance

≤50 °C (≤122 °F) ≥70 °C (≥158 °F)

≤60 °C (≤140 °F) ≥80 °C (≥176 °F)

≤70 °C (≤158 °F) ≥90 °C (≥194 °F)

Devices in integral mount design with single-compartment

housing

Tamb. Temperature resistance

≤50 °C (≤122 °F) ≥75 °C (≥167 °F)

≤60 °C (≤140 °F) ≥85 °C (≥185 °F)

≤70 °C (≤158 °F) ≥95 °C (≥203 °F)

Sensor in remote mount design

Tamb. Temperature resistance

≤50 °C (≤122 °F) ≥105 °C (≥221 °F)

≤60 °C (≤140 °F) ≥110 °C (≥230 °F)

≤70 °C (≤158 °F) ≥120 °C (≥248 °F)

For sensors in remote mount design, the wires in the connection

box must be additionally insulated with the enclosed silicone

hoses starting from ambient temperatures of Tamb. ≥60 °C

(≥140 °F).

Environmental and process conditions for model

FCx4xx…

Ambient temperature Tamb. -20 to 70 °C

(-4 to 158 °F)

-40 to 70 °C*

(-40 to 158 °F)*

Measuring medium temperature

Tmedium

-40 to 205 °C

(-40 to 400 °F)

IP rating / NEMA rating IP 65, IP 67 /

NEMA 4X,Type 4X

* Optional, with order code ‘Ambient temperature range – TA9’

14 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

… 2 Use in potentially explosive atmospheres

… Temperature data

Measuring medium temperature for sensors in integral mount design with dual-compartment housing

Model FCx4xx-A1… and FCx4xx-F1… in Zone 1, Division 1

The table shows the maximum permissible measuring medium temperature as a function of ambient temperature and temperature

class.

Temperature class

Ambient temperature Tamb. T1 T2 T3 T4 T5 T6

≤30 °C (≤86 °F) 205 °C (400 °F)*

130 °C (266 °F)

205 °C (400 °F)*

130 °C (266 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F) 95 °C (203 °F) 80 °C (176 °F)

≤40 °C (≤104 °F) 205 °C (400 °F)*

130 °C (266 °F)

205 °C (400 °F)*

130 °C (266 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F) 95 °C (203 °F) 80 °C (176 °F)

≤50 °C (≤122 °F) 205 °C (400 °F)*

130 °C (266 °F)

205 °C (400 °F)*

130 °C (266 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F) 95 °C (203 °F) 80 °C (176 °F)

≤60 °C (≤140 °F) 205 °C (400 °F)*

130 °C (266 °F)

205 °C (400 °F)*

130 °C (266 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F) 95 °C (203 °F) 80 °C (176 °F)

≤70 °C (≤158 °F) 205 °C (400 °F)*

130 °C (266 °F)

205 °C (400 °F)*

130 °C (266 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F) 95 °C (203 °F) 80 °C (176 °F)

* Only with the ‘Extended tower length – TE1, TE2 or TE3’ order option

Model FCx4xx-A2… and FCx4xx-F2… in Zone 2, Division 2

The table shows the maximum permissible measuring medium temperature as a function of ambient temperature and temperature

class.

Temperature class

Ambient temperature Tamb. T1 T2 T3 T4 T5 T6

≤30 °C (≤86 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F)* 130 °C (266 °F) 95 °C (203 °F) 80 °C (176 °F)*

50 °C (122 °F)

≤40 °C (≤104 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F)* 130 °C (266 °F) 95 °C (203 °F) —

≤50 °C (≤122 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F)* 130 °C (266 °F) — —

≤60 °C (≤140 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F)* 130 °C (266 °F) — —

≤70 °C (≤158 °F) 205 °C (400 °F)*

130 °C (266 °F)

205 °C (400 °F)*

130 °C (266 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F) — —

* Only with the ‘Extended tower length – TE1, TE2 or TE3’ order option

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 15

Measuring medium temperature for sensors in integral mount design with single-compartment housing

Model FCx4xx-A2… and FCx4xx-F2… in Zone 2, Division 2

The table shows the maximum permissible measuring medium temperature as a function of ambient temperature and temperature

class.

Temperature class

Ambient temperature Tamb. T1 T2 T3 T4 T5 T6

≤30 °C (≤86 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F) 95 °C (203 °F) 80 °C (176 °F)

≤40 °C (≤104 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F) 95 °C (203 °F) —

≤50 °C (≤122 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F) 95 °C (203 °F) —

≤60 °C (≤140 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F) — —

≤70 °C (≤158 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F) — —

* Only with the ‘Extended tower length – TE1, TE2 or TE3’ order option

16 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

… 2 Use in potentially explosive atmospheres

… Temperature data

Measuring medium temperature for sensors in remote mount design

Model FCx4xx-A1…, FCx4xx-F1… in Zone 1

The table shows the maximum permissible measuring medium temperature as a function of ambient temperature and temperature

class.

Temperature class

Ambient temperature Tamb. T1 T2 T3 T4

T5 T6

≤30 °C (≤86 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F)

95 °C (203 °F) 80 °C (176 °F)

≤40 °C (≤104 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F)

95 °C (203 °F) 80 °C (176 °F)

≤50 °C (≤122 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F)

95 °C (203 °F) 80 °C (176 °F)

≤60 °C (≤140 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F)

95 °C (203 °F) 80 °C (176 °F)

≤70 °C (≤158 °F) 205 °C (400 °F) 205 °C (400 °F) 195 °C (383 °F) 130 °C (266 °F)

95 °C (203 °F) 80 °C (176 °F)

Model FCx4xx-A2… and FCx4xx-F2… in Zone 2, Division 2

The table shows the maximum permissible measuring medium temperature as a function of ambient temperature and temperature

class.

Temperature class

Ambient temperature Tamb. T1 T2 T3 T4 T5 T6

≤30 °C (≤86 °F) 205 °C (400 °F)*

195 °C (383 °F)

205 °C (400 °F)*

195 °C (383 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F)*

95 °C (203 °F)

95 °C (203 °F)*

80 °C (176 °F)

≤40 °C (≤104 °F) 205 °C (400 °F)*

180 °C (356 °F)

205 °C (400 °F)*

180 °C (356 °F)

195 °C (383 °F)*

130 °C (266 °F)

130 °C (266 °F)*

95 °C (203 °F)

95 °C (203 °F)*

80 °C (176 °F)

—

≤50 °C (≤122 °F) 205 °C (400 °F)*

140 °C (284 °F)

205 °C (400 °F)*

140 °C (284 °F)

130 °C (266 °F)*

130 °C (266 °F)

130 °C (266 °F)*

95 °C (203 °F)

80 °C (176 °F)*

60 °C (140 °F)

—

≤60 °C (≤140 °F) 205 °C (400 °F)*

120 °C (248 °F)

205 °C (400 °F)*

120 °C (248 °F)

130 °C (266 °F)*

120 °C (248 °F)

130 °C (266 °F)*

95 °C (203 °F)

——

≤70 °C (≤158 °F) 180 °C (356 °F)*

80 °C (176 °F)

180 °C (356 °F)*

80 °C (176 °F)

130 °C (266 °F)*

80 °C (176 °F)

130 °C (266 °F)*

80 °C (176 °F)

——

* Only with the ‘Extended tower length – TE1, TE2 or TE3’ order option

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 17

Electrical data

Overview

Standard / No explosion protection Zone 2, 21 Zone 1, 21 (Zone 0)

Division 2 and Zone 2, 21 Division 2 and Zone 1, 21

ATEX:

–

IECEx:

–

ATEX:

II 3 G & II 2 D

IECEx:

Gc & Db

ATEX:

II 1/2 (1) G & II 2 (1) D

II 1/2 G & II 2 D

II 2 (1) G & II 2 (1) D

IECEx:

(Ga) Gb & (Da) Db

Ga/Gb & Db

(Ga) Gb & (Da) Db

USA:

–

Canada:

–

USA:

NI & DIP

AEx ec & AEx tb

Canada:

Non-Incendive & Dust Ignition Proof

Ex ec & Ex tb

USA:

XP-IS & DIP

AEx db ia & AEx ia tb

Canada:

XP-IS & DIP

Ex db ia & Ex ia tb

G11879b

G11879f

APower supply BInputs / outputs, communication CSignal cable (remote mount design only)

• Type of protection ATEX / IECEx: Increased safety

‘Ex e’

• Type of protection USA / Canada: ‘non IS’

• Maximum 250 Vrms

• Terminals: 1+, 2-, L, N,

• Type of protection ATEX / IECEx: Either increased

safety ‘Ex e’ or intrinsically safe ‘Ex ia’

• Type of protection USA / Canada: Either ‘non IS’ or

‘intrinsically safe IS’.

• When installing in ‘Ex ia’ or ‘IS’, suitable

intrinsically safe isolation amplifiers must be used

for the connection.

• Terminals: 31, 32, Uco, V1, V2, V3, V4, 41, 42, 51, 52

• Terminals: A, B, UFE, GRN

• Type of protection ATEX / IECEx: Increased safety

‘Ex e’

• Type of protection USA / Canada: ‘non IS’

Note

When installing in ‘Ex ia’ or ‘IS’ type of protection, the type of protection is determined by the type of electrical connection. The

information in Changing the type of protection on page 26 must be observed when changing the type of protection!

18 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

… 2 Use in potentially explosive atmospheres

… Electrical data

Zone 2, 21 and Division 2 – Model: FCx4xx-A2, FCx4xx-F2

Outputs on basic device Operating values (general) Type of protection – ‘nA’ / ‘NI’

UNINUN

Current / HART output 31 / UCO, active

Terminals 31 / UCO

30 V 30 mA 30 V

30 mA

Current / HART output 31 / 32, passive

Terminals 31 / 32

30 V 30 mA 30 V

30 mA

Digital output 41 / 42, active*

Terminals 41 / 42 and V1 / V2*

30 V 30 mA 30 V

30 mA

Digital output 41 / 42, active**

Terminals 41 / 42 and UCO / 32**

30 V 30 mA 30 V

30 mA

Digital output 41 / 42, passive

Terminals 41 / 42

30 V 25 mA 30 V

25 mA

Digital output 51 / 52, active*

Terminals 51 / 52 and V1 / V2*

30 V 30 mA 30 V

30 mA

Digital output 51 / 52, passive

Terminals 51 / 52

30 V 30 mA 30 V

30 mA

All outputs are electrically isolated from each other and from the power supply.

Digital outputs 41 / 42 and 51 / 52 are not electrically isolated from each other. Terminals 42 / 52 have the same potential.

* Only in conjunction with additional ‘24 V DC loop power supply (blue)’ plug-in card in slot OC1.

** Only in conjunction with current output UCO / 32 in ‘Powermode’, see Current output Uco / 32 as loop power supply for digital output 41 / 42 or 51 / 52 on

page 49.

CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H 19

Inputs and outputs with optional plug-in cards Operating values (general) Type of protection – ‘nA’ / ‘NI’

UNINUNIN

Current output V3 / V4, active*

Terminals V3 / V4 and V1 / V2*

30 V 30 mA 30 V 30 mA

Current output V1 / V2, passive**

Current output V3 / V4, passive**

Terminals V1 / V2** or V3 / V4**

30 V 30 mA 30 V 30 mA

Digital output V3 / V4, active*

Terminals V3 / V4 and V1 / V2*

30 V 25 mA 30 V 25 mA

Digital output V1 / V2, passive**

Digital output V3 / V4, passive**

Terminals V1 / V2** or V3 / V4**

30 V 30 mA 30 V 30 mA

Digital input V3 / V4, active*

Terminals V3 / V4 and V1 / V2

30 V 3,45 mA 30 V 3,45 mA

Digital input V1 / V2, passive**

Digital input V3 / V4, passive**

Terminals V1 / V2** or V3 / V4**

30 V 3,45 mA 30 V 3,45 mA

Digital output V1 / V2, active*

Digital output V3 / V4, active*

Terminals V1 / V2** or V3 / V4**

24 V 22,5 mA 30 V 30 mA

Modbus® / PROFIBUS DP®

Terminals V1 / V2

30 V 30 mA 30 V 30 mA

Ethernet card

Ethernet (various protocols)

Port 1 / Port 2

57 V 417 mA 57 V 417 mA

Ethernet card in connection with Power over Ethernet (POE card)

Ethernet (various protocols)

Port 1 / Port 2

57 V 417 mA 57 V 417 mA

* Only in conjunction with additional ‘24 V DC loop power supply (blue)’ plug-in card in slot OC1.

** The terminal assignment depends on the model number or the slot assignments. For connection examples, see Connection examples on page 53.

20 CoriolisMaster FCB400, FCH400 CORIOLIS MASS FLOWMETER | CI/FCB400/FCH400-EN REV. H

… 2 Use in potentially explosive atmospheres

… Electrical data

Zone 1 ,21 und Division 1 – Model: FCx4xx-A1, FCx4xx-F1

Type of protection ‘e’ / ‘XP’ ‘ia’ / ‘IS’

Outputs on basic device UM

[V]

[A]

[V]

[mA]

[mW]

[nF]

COPA

[nF]

CIPA

[nF]

[mH]

Current / HART output 31 / UCO, active

Terminals 31 / UCO

30 0.2

30 30

115 115

815 815

10 10 5 5

0.08 0.08

Current / HART output 31 / 32, passive

Terminals 31 / 32

30 0.2

—

—115

—815

—27 — 5

0.08 0.08

Digital output 41 / 42, active*

Terminals 41 / 42 and V1 / V2*

30 0.1

27.8 30

119 30

826 225

20 20 29 29

0.22 0.22

Digital output 41 / 42, active**

Terminals 41 / 42 and UCO / 32**

30 0.1

30 30

115 115

826 225

16 16 10 10

0.08 0.08

Digital output 41 / 42, passive

Terminals 41 / 42

30 0.1

—

—30

—225

—27 — 5

—0.08

Digital output 51 / 52, active*

Terminals 51 / 52 and V1 / V2*

30 0.1

27.8 30

119 30

826 225

20 20 29 29

0.22 0.22

Digital output 51 / 52, passive

Terminals 51 / 52

30 0.1

—

—30

—225

—27 — 5

—0.08

All outputs are electrically isolated from each other and from the power supply.

Digital outputs 41 / 42 and 51 / 52 are not electrically isolated from each other. Terminals 42 / 52 have the same potential.

* Only in conjunction with additional ‘24 V DC loop power supply (blue)’ plug-in card in slot OC1.

** Only in conjunction with current output UCO / 32 in ‘power mode’, see Current output Uco / 32 as loop power supply for digital output 41 / 42 or 51 / 52 on

page 49.