ABB AWT210 User manual

—
ABB MEASUREMENT & ANALYTICS | COMMUNICATIONS SUPPLEMENT
AWT210
PROFIBUS PA 2-wire transmitter
Measurement made easy
Introduction
This Communications Supplement provides
procedures specifically related to the AWT210
PROFIBUS PA® 2-wire transmitter. Refer to the
AWT210 Operating Instruction (OI/AWT210-EN) for
general information on installation, operation and
maintenance.
For more information
Further publications for the AWT210 transmitter are
available for free download from:
www.abb.com/measurement
or by scanning this code:
Search for or click on:

Data Sheet DS

Commissioning Instruction C 

Operating Instruction 
—
AWT210
2-Wire transmitter

2AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
Contents
1 Health & Safety ..............................3
Document symbols .................................3
Safety precautions .................................3
Potential safety hazards ............................3
................3
Safety standards ...................................3
Waste Electrical and Electronic Equipment (WEEE) .. 4
Product recycling and disposal (Europe only) ....... 4
Information on ROHS Directive 2011/65/EU (RoHS II) 4
Product symbols .................................. 4
2 Cyber security...............................5
3 Profibus PA..................................5
4 Device overview .............................6
Reference documents ............................. 6
5 Transmitter functionality and
operator interface controls .......................6
Process interface ................................. 6
Sensor Input Channels ........................6
Host interface ................................6
Local interfaces, jumpers and switches ............. 6
Local controls and displays....................6
Internal jumpers and switches.................6
6 Installation .................................7
Cable length ...................................... 8
Cable specification ................................ 8
Network connection ............................... 8
7 Configuration ...............................9
Local configuration................................ 9
Integration using GSD ............................. 9
AWT210 Profibus data sheet ....................... 9
8 PROFIBUS slots ............................ 10
..............................10
........................12
 ...14
 ......16
 ..18
 ................ 20
9 Device tables ...............................21
Sales Service Software

AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A 3
1 Health & Safety
Document symbols
Symbols that appear in this document are explained below:
DANGER – SERIOUS DAMAGE TO HEALTH
This symbol in conjunction with the signal word
‘DANGER’ indicates an imminent electrical hazard.
Failure to observe this safety information will result in
death or severe injury.
WARNING – BODILY INJURY
This symbol in conjunction with the signal word
‘WARNING’ indicates a potential electrical hazard.
Failure to observe this safety information will result in
death or severe injury.
CAUTION – MINOR INJURIES
This symbol in conjunction with the signal word
‘CAUTION’ indicates a potentially dangerous
situation. Failure to observe this safety information
may result in minor or moderate injury. The symbol
may also be used for property damage warnings.
IMPORTANT (NOTE)
This symbol indicates operator tips, particularly
useful information or important information about
the product or its further uses. The signal word
‘IMPORTANT (NOTE)’ does not indicate a dangerous
or harmful situation.
Safety precautions
Be sure to read, understand and follow the instructions
contained within this manual before and during use of the
equipment. Failure to do so could result in bodily harm or
damage to the equipment.
WARNING – BODILY INJURY
Installation, operation, maintenance and servicing
must be performed:
• by suitably trained personnel only
• in accordance with the information provided in this
manual
• in accordance with relevant national and local
regulations
Potential safety hazards
AWT210 transmitter – electrical
WARNING – BODILY INJURY
To ensure safe use when operating this equipment,
the following points must be observed:
• Up to 240 V AC may be present. Be sure to isolate
the supply before removing the terminal cover.
• Normal safety precautions must be taken to avoid
the possibility of an accident occurring when
operating in conditions of high pressure and/or
temperature.
Safety advice concerning the use of the equipment
described in this manual or any relevant Material
Safety Data Sheets (where applicable) can be
obtained from the Company, together with servicing
and spares information.
Safety standards
This product has been designed to satisfy the requirements of
IEC61010-1:2010 3rd edition ‘Safety Requirements for Electrical
Equipment for Measurement, Control and Laboratory Use’ and
complies with US NEC 500, NIST and OSHA.
This equipment complies with the requirements of CEI/IEC
61010-1:2010 ‘Safety Requirements for Electrical Equipment for
Measurement, Control and Laboratory Use’ and complies with
US NEC 500 and Occupational Safety & Health Administration.
If the equipment is used in a manner NOT specified by the
Company, the protection provided by the equipment may be
impaired.

4AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
…1 Health & Safety
Waste Electrical and Electronic Equipment
(WEEE)
WEEE EU Directive 2012/19/EU covers disposal and recycling
of electronic equipment at the end of life for reasons of
environmental protection.
For industrial installations, portable equipment is
included. This means that when the transmitter is
used with a portable sensor, it is included in
directive’s scope and has the WEEE symbol (left) on
its data label. Therefore, at the end of life, contact the
supplier for specialist waste recycling. It must not be
disposed of as municipal waste.
Permanent Industrial installations are not designated within
this directive for recycling. At the point of supply the intended
use is not always known, so the WEEE symbol is included on all
remote forms of the transmitter.
Product recycling and disposal (Europe only)
Electrical equipment marked with this symbol may
not be disposed of in European public disposal
systems after 12 August 2005. To conform to
European local and national regulations (EU Directive
2012/19/EU), European electrical equipment users
can now return old or end-of-life equipment to the
manufacturer for disposal at no charge to the user.
ABB is committed to ensuring that the risk of any
environmental damage or pollution caused by any of
its products is minimized as far as possible.
IMPORTANT (NOTE)
For return for recycling, please contact the equipment
manufacturer or supplier for instructions on how to
return end-of-life equipment for proper disposal.
Information on ROHS Directive 2011/65/EU
(RoHS II)
ABB, Industrial Automation, Measurement & Analytics, UK, fully
supports the objectives of the ROHS II directive. All in-scope
products placed on the market by IAMA UK on and following the
22nd of July 2017 and without any specific exemption, will be
compliant to the ROHS II directive, 2011/65/EU.
Product symbols
Symbols that may appear on this product are shown below:
Risk of electric shock.
This symbol, when noted on a product, indicates a
potential hazard which could cause serious personal
injury and/or death. The user should reference this
instruction manual for operation and/or safety
information.
Protective earth (ground) terminal.
Functional earth (ground) terminal.
Direct current supply only.
This symbol, when noted on a product enclosure or
barrier, indicates that a risk of electrical shock and/or
electrocution exists and indicates that only
individuals qualified to work with hazardous voltages
should open the enclosure or remove the barrier.
Recycle separately from general waste under the
WEEE directive.

AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A 5
2 Cyber security
The AWT210 PROFIBUS PA® transmitter is designed to be
connected to and to communicate information and data via a
digital communication interface. It is your sole responsibility to
provide and continuously ensure a secure connection between
the product and your network or any other network (as the case
may be). You shall establish and maintain any appropriate
measures (such as but not limited to the application of
authentication measures etc.) to protect the product, the
network, its system and the interface against any kind of
security breaches, unauthorized access, interference, intrusion,
leakage and/or theft of data or information.
ABB Ltd and its affiliates are not liable for damages and/or
losses related to such security breaches, any unauthorized
access, interference, intrusion, leakage and/or theft of data or
information.
3 Profibus PA
PROFIBUS is an all-digital, serial, two-way communication
system that serves as a Local Area Network (LAN) for factory/
plant instrumentation and control devices.
PROFIBUS is a manufacturer-independent, open Fieldbus
standard for a wide range of applications in manufacturing,
process and building automation. Manufacturer independence
and openness are ensured by the international standard EN
50170.
The AWT210 transmitter meets the requirements of PROFIBUS
PA Application profile 3.02.
Using the PROFIBUS protocol, devices from different
manufacturers exchange information on the same
communications bus without the need for special interface
equipment.
Information on PROFIBUS PA can be found in the PNO Guideline
and standards IEC 61158, IEC 61784, EN 50170/DIN 19245 and
EN 50020 (FISCO model).
For further information on Profibus, refer to:
the PI organization website:
www.profibus.com
or the ABB website:
www.abb.com/fieldbus

6AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
4 Device overview
Four variants of AWT210 are available for use with pH, ORP,
pION, and conductivity sensors.
Supported sensors:
• pH
• 2-electrode conductivity
• 4-electrode conductivity
• toroidal conductivity
The AWT210 PROFIBUS PA is compliant with the PNO Profile for

The AWT210 PROFIBUS PA is a compact slave device
implementing:
• one Physical Block (PB)
the PBs describes the necessary parameters and
functions of the device or the operation of the device
hardware itself.
• four Transducer Blocks (TB)
the TBs contain the parameters of a device representing
the necessary parameters and functions of the
connection to the process.
Examples are measured process values, the type of
sensor and the calibration data.
There is one transducer block for each sensor type.
• two Function Blocks (FB)
both function blocks are AI blocks.
each FB can be connected to one TB at one time.
Reference documents
Document ID Title
 
 
 
5 Transmitter functionality and
operator interface controls
Process interface
Sensor Input Channels
The sensor module provides 8 terminals marked 1 to 8, 1 to 4 for
Process Variable (detailed in commissioning instructions) and 5
to 8 for temperature sensor (up to 3 wire RTD + shield).
Operating ranges correspond to the capabilities of each sensor
type.
Host interface
The AWT210 PA is a Bus Powered device with Profibus PA
communication. The communication module provides 5
terminals for bus power & functional earth connection.
• Terminals 1(A) & 2(B) are for polarity independent bus lines.
• Terminal 3 ( ) provides a functional earth connection.
• Terminals 4(A) & 5(B) are a repeat of Terminals 1(A) & 2(B).
Local interfaces, jumpers and switches
Local controls and displays
• The Device has a 75 x 65 mm (3.00 x 2.55 in.) monochromatic
dot matrix LCD display and 4 push buttons
Internal jumpers and switches
The device has 2 internal switches, situated on the

see Figure 2, page 8:
• SW1: Reset to Defaults
if the device is powered up with SW1 in the ON position it
returns device setup to default factory settings.
if powered up with SW1 in the OFF position the device
retains previously saved user settings*.
• SW2: Write Protection
If SW2 is in the ON position HW write protect shows as
enabled and the user is unable to make changes to setup
or send Write commands via PROFIBUS®.
With SW2 in OFF position the user is able to make
changes/send commands providing they are in a
sufficient access level and Software Write Protect has
not been enabled.
*Note: Reset to defaults is not performed if SW2 Write
Protection is ON.

AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A 7
6 Installation
All devices are connected in a bus structure ('line') as shown in
Figure 1.
The number of transmitters or devices that can be connected
to a bus is primarily dependent on the power consumption of
the transmitters or devices, the type of cable, the number of
spurs, the total cable length of the bus and intrinsic safety
requirements.
Each end of a segment must be terminated by an active bus
terminating resistor. Both bus terminators must always be
powered to ensure fault-free operation, therefore it is strongly
recommended that they are connected to a back-up power
supply.
The PROFIBUS PA furnishes transmitter power and can be
configured as a point-to-point, tree, Daisy Chain, or Trunk/
Spurs network. Modulating the base quiescent current
generates the communication signals. The quiescent current
value is used as a reference to establish the number of devices
that can be installed on a single bus line.
Data is transmitted over the bus using digital, bit synchronous
Manchester II coding at a baud rate of 31.25 kbit/sec.
Figure 1 Typical PROFIBUS network
Engineer
Control
Profibus-DP
Profibus-PA
DP/PA link
AWT210
2-wire transmitter
Operate
Operational
level
Master
level
Slave
level

8AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
…6 Installation
Cable length
Maximum cable length 1900 m (6233 ft)
Maximum spur length (1 device) 120 m (394 ft)
Maximum spur length (2 devices) 90 m (295 ft)
Maximum spur length (3 devices) 60 m (197 ft)
Maximum spur length (4 devices) 30 m (98 ft)
Cable specification
The cable lengths in Table 1 apply to cable to the following
specification:
 
Capacitance per unit length <30 pf/m
 
Core diameter 0.64 mm
Core cross section >0.34 mm2
Network connection
PROFIBUS network connections are made to the terminal block
on the AWT210 Communication module.
WARNING – BODILY INJURY
• Refer to the AWT210 Operating Instruction
(OI/AWT210 -EN) before making electrical
connections.
NOTICE
Property damage
When connecting an AWT210 to a PROFIBUS-PA network:
• Use cable that meets PROFIBUS specifications for
reliable communications
• Ensure a PROFIBUS active terminator is fitted to
each end of each bus segment.
• Route data lines clear of the source of any strong
electrical and magnetic fields.
Figure 2 PROFIBUS PA communication module connection overview
SW1:
Reset to
defaults
ON
OFF
SW2:
Write
protection
123456 87
AB
2
AB
1435
Sensor module connections
PROFIBUS PA module
connections
(connected internally)
Non IS installations
9 to 32 V DC
IS installations
9 to 24 V DC
Functional earth

AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A 9
7 Configuration
Local configuration
The configuration of PROFIBUS communications for an AWT210
transmitter can be set locally using the keypad and menus
however it is recommended that the configuration is set
remotely by a Profibus master.
Communication
Ex it
Menu
Select
Used to configure the communications.
Menu Comment Default
Slave address Device-specific slave address to identify the transmitter on the network. 
Tag Descriptor String to identify the device (displayed at the top of the operator page) 
Ident No. Selector  
Manuf ID Read Only Manufacturer Identification number 
Device Type Read Only Indicates the Profibus PA Device Type Analyzer
PA Profile Read Only Indicates the Profibus PA profile version 
Integration using GSD
PROFIBUS devices differ with respect to available functionality
and parameters for each device type and manufacturer. In order
to obtain 'Plug-and-Play' configuration for PROFIBUS,
characteristic device communication features such as
manufacturer name, device name, hardware/software versions,
baud rate and the number and nature of inputs/outputs are
defined in an electronic device data sheet known as a GSD
(Generic Station Description) file.
A GSD file is readable ASCII text file that contains both general
and device-specific specifications for communication. Each of
the entries describes a feature supported by a device. By using
keywords, a configuration tool reads the device identification,
the adjustable parameters, the corresponding data type and
the permitted limit values for the configuration of the device
from the GSD. Some keywords are mandatory (for example,
Vendor_Name), others are optional (for example, Sync_Mode_
supported).
The GSD file for AWT210 transmitters specifies the device
specific Ident No. 3404 and conforms to the PROFIBUS
standard, providing a clear and comprehensive description of
each instrument in a precisely defined format. The description
enables the system configuration tool to use the information
automatically when configuring a PROFIBUS bus system.
The AWT210 GSD file (ABB_3404.gsd) is available for download
from the ABB website at:
www.abb.com/fieldbus (follow the link for PROFIBUS DP
field devices).
AWT210 Profibus data sheet
Item Detail
Device name 
Profile ident
support

Device Specific, Adaptation Mode,
PNO ID no. 
Bus Address 
Block types
one Physical Block
four Transducer Blocks,
two AI Function Blocks
Physical Layer 
Transmission rate 

10 AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
8 PROFIBUS slots
Physical block – slot 0
The PB mapping is located on slot 0.
The initial index is 16 and this number must be added to the
relative Index in column index to get the absolute index.

Index

Parameter Access Data Type Size
(bytes)
Range
STANDARD PARAMETERS
 BLOCK_OBJECT RRecord  
 ST_REV RSimple  
 TAG _DESC RW Simple OctetString  Dev ice TAG
 STRATEGY RW Simple  
 ALERT_KEY RW Simple  
 TARGET_MODE RW Simple  AUTO
 MODE_BLK RRecord  
 ALARM_SUM RRecord  
STANDARD PHYSICAL BLOCK PARAMETERS
 SOFTWARE_REVISION RSimple VisibleString 
 HARDWARE_REVISION RSimple VisibleString 
 DEVICE_MAN_ID RSimple  
 DEVICE_ID RSimple VisibleString 
 DEVICE_SER_NUM RSimple VisibleString 
 DIAGNOSIS RSimple OctetString 
 DIAGNOSIS_EXT RSimple OctetString 
 DIAGNOSIS_MASK RSimple OctetString 
 DIAGNOSIS_MASK_EXT RSimple OctetString 
 DEVICE_CERTIFICATION RSimple VisibleString 
 WRITE_LOCKING RW Simple   
 FACTORY_RESET RW Simple   
 DESCRIPTOR RW Simple OctetString 
 DEVICE_MESSAGE RW Simple OctetString 
 DEVICE _ INSTAL _DATE RW Simple OctetString 
 LOCAL_OP_ENA RW Simple   
 IDENT_NUMBER_SELECTOR RW Simple   
 HW_WRITE_PROTECTION RSimple   
 FEATURE RRecord  
 COND_STATUS_DIAG RW Simple  
 DIAG_EVENT_SWITCH RW Record Diag-switch 
 NULL_ // reserved by PI
ANALYZER FIELD DEVICE SPECIFIC PHYSICAL BLOCK PARAMETERS
 DEVICE_CONFIGURATION RSimple VisibleString 
 INIT_STATE RW Simple  
 DEVICE _ STATE RW Simple  
 GLOBAL_STATUS RSimple  
 NULL_ // reserved by PI

11
AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
Index

Parameter Access Data Type Size
(bytes)
Range

 CB_FW_REVISION RSimple VisibleString 
 CB_HW_REVISION RSimple VisibleString 
 FE_FW_REVISION RSimple VisibleString 
 FE_HW_REVISION RSimple VisibleString 
 DIAGNOSIS_WORST_COND RSimple  
 DIAGNOSIS_EXT_HISTORY RSimple OctetString 
 DIAGNOSIS_DETAILS RRecord DIAGNOSIS_DETAILED 
 DIAGNOSIS_SIMULATION_STATUS RW Simple  
 DIAGNOSIS_EXT_SIMULATION RW Simple OctetString 
 DIAGNOSIS_EXT_MASK RW Simple OctetString 
 ASSEMBLY_DATE RSimple OctetString 
 SAVINGS RW Simple  
 SERVICES RW Simple  
 NULL// ABB Reserved
 PASSWORD RW Simple VisibleString 
 ADDRESS RW Record PRIVATE_ADDRESS 
 DATA RW Record PRIVATE_DATA 
 MEMORY_ADDRESS RW Record PRIVATE_MEMORY_
ADDRESS 
 MEMORY_DATA RW Record PRIVATE_DATA 
 TEST_RESULT RW Simple  
 DEVICE_SERIAL_NUMBER RSimple VisibleString 
 DISP_CONTRAST RW Simple   
 LANGUAGE RW Simple   
 FE_BOARD_TYPE RSimple   
 SENSOR_DIAG RW Simple   

12 AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
…8 PROFIBUS slots
pH Transducer block – slot 1
Index Parameter Access Data Type Size (bytes) Range
STANDARD PARAMETERS
BLOCK_OBJECT RRecord  
ST_REV RSimple  
TAG_DESC RW Simple OctetString 
STRATEGY RW Simple  
ALERT_KEY RW Simple  
TARGET_MODE RW Simple  AUTO
MODE_BLK RRecord  
ALARM_SUM RRecord  
ANALYZER FIELD DEVICE SPECIFIC TRANSDUCER BLOCK PARAMETERS
COMPONENT_NAME RW Simple OctetString 
PV RRecord  
 PV_UNIT RW Simple   
 PV_UNIT_TEXT RW Simple OctetString 
 ACTIVE_RANGE RW Simple  
 AUTORANGE_ON RW Simple Bool 
 SAMPLING_RATE RW Simple Time_Diff 
 NULL_ // reserved by PI
 NUMBER_OF_RANGES RSimple  
  RW Record  

 PV_MIN_SPAN RSimple Float 
 SENSOR_RANGE RRecord  
 MEASUREMENT_TYPE RW Simple   
  RRecord  
  RW Simple   
  RRecord  
  RW Simple   
  RRecord   
  RW Simple   
 SENSOR_TYPE RW Simple   
 ISO_POTENTIAL RW Simple Float  
 ASY_POTENTIAL RW Simple Float  
 VALENCE RW Simple   
 MAGNITUDE RW Simple   
 END_MAGNITUDE RW Simple   
 END_MV RW Simple   
 TEMP_UNIT RW Simple   
 TEMP_COMP_TYPE RW Simple   
 MANUAL_TEMP RW Simple Float  
 PH_SOLN_COEFF RW Simple Float  
 MV_ SOLN_COEFF RW Simple Float  
 TEMP_SENSOR_TYPE RSimple   
 NULL_ // reserved by PI
 TEMP_SENSOR_AR_TRIGGER WSimple   
 TEMP_SENSOR_AR_STATUS RSimple   
 REF_IMP_LIMIT RW Simple Float  
 SENSOR_DIAG RW Simple   
 DAMPING_TIME RW Simple Float  

13
AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
Index Parameter Access Data Type Size (bytes) Range

 AUTO_CAL_BUFF_TYPE RW Simple   
  RW Simple   
  RW Simple   
  RW Array Float  
  RW Array Float  
  RW Array Float  
  RW Array Float  
 CAL_MODE RW Simple  
 CAL _STATUS RW Simple  
 CAL_PROGRESS_TIMER RSimple Float 
 CAL_ERROR_VAL RSimple  
 PV_CAL_SLOPE RW Simple Float  
 PV_CAL_OFFSET RW Simple Float  
 TEMP_CAL_SLOPE RW Simple Float  
 TEMP_CAL_OFFSET RW Simple Float  
 CAL_RESET RW Simple   

 CAL_POINT RW Simple Float 
 PV_SLOPE_ALARM_LIMIT_HI RW Simple Float  
 PV_SLOPE_ALARM_LIMIT_LO RW Simple Float  
 PV_OFFSET_ALARM_LIMIT RW Simple Float  
  RW Simple Float  
  RW Simple Float  
  RW Simple Float  
 PV_FAC_CAL_LOW RW Simple  
 PV_FAC_CAL_HIGH RW Simple  
  RW Simple  
  RW Simple  
 PV_FAC_CAL_COEFFS RArray Float 
 REFZ_FAC_CAL_COEFFS RArray Float 

14 AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
…8 PROFIBUS slots
2-electrode conductivity transducer block – slot 2
Index Parameter Access Data Type Size (bytes) Range
STANDARD PARAMETERS
BLOCK_OBJECT RRecord  
ST_REV RSimple  
TAG_DESC RW Simple OctetString 
STRATEGY RW Simple  
ALERT_KEY RW Simple  
TARGET_MODE RW Simple  AUTO
MODE_BLK RRecord  
ALARM_SUM RRecord  
ANALYZER FIELD DEVICE SPECIFIC TRANSDUCER BLOCK PARAMETERS
COMPONENT_NAME RW Simple OctetString 
PV RRecord  
 PV_UNIT RW Simple   
 PV_UNIT_TEXT RW Simple OctetString 
 ACTIVE_RANGE RW Simple  
 AUTORANGE_ON RW Simple Bool 
 SAMPLING_RATE RW Simple Time_Diff 
 NULL_ // reserved by PI
 NUMBER_OF_RANGES RSimple  
  RW Record  

 PV_MIN_SPAN RSimple Float 
 SENSOR_RANGE RRecord  
 MEASUREMENT_TYPE RW Simple   
  RRecord  
  RW Simple   
  RRecord  
  RW Simple   
  RRecord   
  RW Simple   
 COND_UNITS_MODE RW Simple   
 CELL_CONSTANT RW Simple Float  
 CONC_CURVE_NAME RW Simple OctetString 
 CONC_CURVE_TABLE_X_COND RW Array Float  
 CONC_CURVE_TABLE_Y_CONC RW Array Float  
 TEMP_UNIT RW Simple   
 TEMP_COMP_TYPE RW Simple   
 MANUAL_TEMP RW Simple Float  
 AUTO_TC_OPTION RW Simple   
 TC_COEFFICIENT RW Simple Float  
  RW Simple   
 USER_DEF_TC_CURVE_X_TEMP RW Array Float  
 USER_DEF_TC_CURVE_Y_TEMP RW Array Float  
 REFERENCE_TEMP RW Simple Float  
 Reserved by PI
 TEMP_SENSOR_TYPE RSimple   
 TEMP_SENSOR_AR_TRIGGER WSimple   
 TEMP_SENSOR_AR_STATUS RSimple   
 SENSOR_DIAG RW Simple   

15
AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
Index Parameter Access Data Type Size (bytes) Range

 DAMPING_TIME RW Simple Float  
 CAL_MODE RW Simple  
 CAL _STATUS RSimple  
 CAL_PROGR_TIMER RSimple Float 
 CAL_ERROR_VAL RSimple  
 PV_CAL_SLOPE RW Simple Float  
 PV_CAL_OFFSET RW Simple Float  
 TEMP_CAL_SLOPE RW Simple Float  
 TEMP_CAL_OFFSET RW Simple Float  
 CAL_RESET WSimple   
 CAL_POINT RW Simple Float 
 FAC_CAL_ACTION WSimple  
 FAC_CAL_STATUS RW Simple  
 PV_FAC_CAL_SLOPE RArray Float 
 PV_FAC_CAL_OFFSET RArray Float 
 SPV_FAC_CAL_SLOPE RArray Float 
 SPV_FAC_CAL_OFFSET RArray Float 

16 AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
…8 PROFIBUS slots
Toroidal conductivity transducer block – slot 3
Index Parameter Access Data Type Size (bytes) Range
STANDARD PARAMETERS
BLOCK_OBJECT RRecord  
ST_REV RSimple  
TAG_DESC RW Simple OctetString 
STRATEGY RW Simple  
ALERT_KEY RW Simple  
TARGET_MODE RW Simple  AUTO
MODE_BLK RRecord  
ALARM_SUM RRecord  
ANALYZER FIELD DEVICE SPECIFIC TRANSDUCER BLOCK PARAMETERS
COMPONENT_NAME RW Simple OctetString 
PV RRecord  
 PV_UNIT RW Simple   
 PV_UNIT_TEXT RW Simple OctetString 
 ACTIVE_RANGE RW Simple  
 AUTORANGE_ON RW Simple Bool 
 SAMPLING_RATE RW Simple Time_Diff 
 NULL_ // reserved by PI
 NUMBER_OF_RANGES RSimple  
  RW Record  

 PV_MIN_SPAN RSimple Float 
 SENSOR_RANGE RRecord  
 MEASUREMENT_TYPE RW Simple   
  RRecord  
  RW Simple   
  RRecord  
  RW Simple   
  RRecord   
  RW Simple   
 COND_UNITS_MODE RW Simple   
 CONCENTRATION_SOLUTION RW Simple   
 CONC_CURVE_NAME RW Simple OctetString 
 CONC_CURVE_TABLE_X_COND RW Array Float  
 CONC_CURVE_TABLE_Y_CONC RW Array Float  
 TEMP_UNIT RW Simple   
 TEMP_COMP_TYPE RSimple   
 MANUAL_TEMP RW Simple Float  
 AUTO_TC_OPTION RW Simple   
 TC_COEFFICIENT RW Simple Float  
 USER_DEF_TC_CURVE_X_TEMP RW Array Float  
 USER_DEF_TC_CURVE_Y_KREF RW Array Float  
 REFERENCE_TEMP RW Simple Float  
 TEMP_SENSOR_TYPE RSimple   
 Reserved by PI
 TEMP_SENSOR_TYPE RSimple   
 TEMP_SENSOR_AR_TRIGGER WSimple   
 TEMP_SENSOR_AR_STATUS RSimple   
 SENSOR_DIAG RW Simple   

17
AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
Index Parameter Access Data Type Size (bytes) Range

 DAMPING_TIME RW Simple Float  
 CAL_MODE RW Simple  
 CAL _STATUS RSimple  
 CAL_PROGR_TIMER RSimple Float 
 CAL_ERROR_VAL RSimple  
 PV_CAL_SLOPE RW Simple Float  
 PV_CAL_OFFSET RW Simple Float  
 TEMP_CAL_SLOPE RW Simple Float  
 TEMP_CAL_OFFSET RW Simple Float  
 CAL_RESET WSimple   
 CAL_POINT RW Simple Float 
 FAC_CAL_ACTION WSimple  
 FAC_CAL_STATUS RW Simple  
 PV_FAC_CAL_SLOPE RArray Float 
 PV_FAC_CAL_OFFSET RArray Float 
 SPV_FAC_CAL_SLOPE RArray Float 
 SPV_FAC_CAL_OFFSET RArray Float 

18 AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
…8 PROFIBUS slots
4-electrode conductivity transducer block – slot 4
Index Parameter Access Data Type Size (bytes) Range
STANDARD PARAMETERS
BLOCK_OBJECT RRecord  
ST_REV RSimple  
TAG_DESC RW Simple OctetString 
STRATEGY RW Simple  
ALERT_KEY RW Simple  
TARGET_MODE RW Simple  AUTO
MODE_BLK RRecord  
ALARM_SUM RRecord  
ANALYZER FIELD DEVICE SPECIFIC TRANSDUCER BLOCK PARAMETERS
COMPONENT_NAME RW Simple OctetString 
PV RRecord  
 PV_UNIT RW Simple   
 PV_UNIT_TEXT RW Simple OctetString 
 ACTIVE_RANGE RW Simple  
 AUTORANGE_ON RW Simple Bool 
 SAMPLING_RATE RW Simple Time_Diff 
 NULL_ // reserved by PI
 NUMBER_OF_RANGES RSimple  
  RW Record  

 PV_MIN_SPAN RSimple Float 
 SENSOR_RANGE RRecord  
 MEASUREMENT_TYPE RW Simple   
  RRecord  
  RW Simple   
  RRecord  
  RW Simple   
  RRecord   
  RW Simple   
 COND_UNITS_MODE RW Simple   
 SENSOR_GROUP RW Simple   
 CONCENTRATION_SOLUTION RW Simple   
 CONC_CURVE_NAME RW Simple OctetString 
 CONC_CURVE_TABLE_X_COND RW Array Float  
 CONC_CURVE_TABLE_Y_CONC RW Array Float  
 TEMP_UNIT RW Simple   
 TEMP_COMP_TYPE RSimple   
 MANUAL_TEMP RW Simple Float  
 AUTO_TC_OPTION RW Simple   
 TC_COEFFICIENT RW Simple Float  
 USER_DEF_TC_CURVE_X_TEMP RW Array Float  
 USER_DEF_TC_CURVE_Y_KREF RW Array Float  
 Reserved by PI
 REFERENCE_TEMP RW Simple Float  
 TEMP_SENSOR_TYPE RSimple   
 TEMP_SENSOR_AR_TRIGGER WSimple   
 TEMP_SENSOR_AR_STATUS RSimple   
 SENSOR_DIAG RW Simple   

19
AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
Index Parameter Access Data Type Size (bytes) Range

 DAMPING_TIME RW Simle Float  
 CAL_MODE RW Simple  
 CAL _STATUS RSimple  
 CAL_PROGR_TIMER RSimple Float 
 CAL_ERROR_VAL RSimple  
 PV_CAL_SLOPE RW Simple Float  
 PV_CAL_OFFSET RW Simple Float  
 TEMP_CAL_SLOPE RW Simple Float  
 TEMP_CAL_OFFSET RW Simple Float  
 CAL_RESET WSimple   
 CAL_POINT RW Simple Float 
 FAC_CAL_ACTION WSimple  
 FAC_CAL_STATUS RW Simple  
 PV_FAC_CAL_SLOPE RArray Float 
 PV_FAC_CAL_OFFSET RArray Float 
 GNDLP_FAC_CAL_SLOPE RArray Float 
 GNDLP_FAC_CAL_OFFSET RArray Float 

20 AWT210 PROFIBUS PA 2-WIRE TRANSMITTER | COM/AWT210/PROFIBUS-EN REV. A
…8 PROFIBUS slots
Analog input blocks – slots 5 and 6
AI_1 mapping is located on slot 5. AI_2 mapping is located on slot 6.
The initial index is 16 and this number must be added to the relative
Index in column index to get the absolute index.

Index

Parameter Access Data Type Size
(bytes)
Range
STANDARD PARAMETERS
 BLOCK_OBJECT RRecord  
 ST_REV RSimple  
 TAG _DESC RW Simple OctetString 
 STRATEGY RW Simple  
 ALERT_KEY RW Simple  
 TARGET_MODE RW Simple   
 MODE_BLK RRecord  
 ALARM_SUM RRecord  
 BATCH R/W Record  
STANDARD AI BLOCK PARAMETERS
 NULL_ // reserved by PI
 OUT RW Record  
 PV_SCALE RW Array Float  
 OUT_SCALE RW Record  
 LIN_TYPE RW Simple  
 CHANNEL RW Simple  
 NULL_ // reserved by PI
 PV_FTIME RW Simple Float  
 FSAFE_TYPE RW Simple   
 FSAFE_VALUE RW Simple Float 
 ALARM_HYS RW Simple Float 
 NULL_ // reserved by PI
 HI_HI_LIM RW Simple Float 
 NULL_ // reserved by PI
 HI_LIM RW Simple Float 
 NULL_ // reserved by PI
 LO_LIM RW Simple Float 
 NULL_ // reserved by PI
 LO_LO_LIM RW Simple Float 
 NULL_ // reserved by PI
 HI_HI_ALM RRecord  
 HI_ALM RRecord  
 LO_ALM RRecord  
 LO_LO_ALM RRecord  
 SIMULATE RW Record   
 OUT_UNIT_TEXT RW Simple OctetString 