ABB TZIDC-200 User manual

Operating Instruction
42/18-85-EN
Electro-Pneumatic Positione
r
TZIDC-200, TZIDC-210, TZIDC-220
for 4 ... 20 mA two-wire technology,
HART, PROFIBUS PA,
FOUNDATION fieldbus

Blinder Text
2 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
Electro-Pneumatic Positioner
TZIDC-200, TZIDC-210, TZIDC-220
Operating Instruction
42/18-85-EN
04.2016
Rev. D
Translation of the original instruction
Manufacturer:
ABB Automation Products GmbH
Process Automation
Schillerstraße 72
32425 Minden
Germany
Tel.: [phone]
Fax: [phone]
Customer service center
Phone: [phone]
[email protected]
© Copyright 2016 by ABB Automation Products GmbH
Subject to changes without notice
This document is protected by copyright. It assists the user in safe and efficient operation of the device. The contents of this
document, whether whole or in part, may not be copied or reproduced without prior approval by the copyright holder.
Contents

Contents
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 3
1Safety.............................................................................................................................................................5
1.1General information and notes for the reader ................................................................................................5
1.2Intended use...................................................................................................................................................5
1.3Target groups and qualifications ....................................................................................................................5
1.4Warranty provisions........................................................................................................................................6
1.5Plates and symbols ........................................................................................................................................6
1.5.1Safety- / warning symbols, note symbols................................................................................................6
1.5.2Name plate..............................................................................................................................................7
1.6Transport safety information...........................................................................................................................7
1.7Storage conditions..........................................................................................................................................7
1.8Installation safety information.........................................................................................................................8
1.9Safety information for electrical installation....................................................................................................8
1.10Operating safety information ..........................................................................................................................8
1.11Returning devices...........................................................................................................................................9
1.12Integrated management system.....................................................................................................................9
1.13Disposal........................................................................................................................................................10
1.13.1Information on WEEE Directive 2002/96/EC (Waste Electrical and Electronic Equipment).................10
1.13.2RoHS Directive 2002/95/EC .................................................................................................................10
2Ex relevant safety instructions .................................................................................................................10
3Design and function...................................................................................................................................12
4Mounting .....................................................................................................................................................13
4.1Operating conditions at installation site........................................................................................................13
4.2Mechanical mount ........................................................................................................................................13
4.2.1General information...............................................................................................................................13
4.2.2Mounting on linear actuators.................................................................................................................15
4.2.3Mounting on part-turn actuator..............................................................................................................20
5Electrical connections ...............................................................................................................................23
5.1Screw terminal assignments ........................................................................................................................24
5.2Cable entry ...................................................................................................................................................25
5.3Setting the mechanical feedback .................................................................................................................25
5.3.1Mechanical position indicator................................................................................................................25
5.3.2Mechanical digital feedback with proximity switches ............................................................................26
5.3.3Mechanical feedback with micro switches for 24 V ..............................................................................26
6Pneumatic connection ...............................................................................................................................27
7Commissioning ..........................................................................................................................................28
7.1TZIDC-200....................................................................................................................................................28
7.1.1Operating modes...................................................................................................................................29
7.1.2Sample parameters...............................................................................................................................30
7.2TZIDC-210 / TZIDC-220...............................................................................................................................32
7.2.1Setting the bus address ........................................................................................................................34
7.2.2Request information..............................................................................................................................35
7.2.3Operating modes...................................................................................................................................35
7.2.4Sample parameters...............................................................................................................................36
8Maintenance................................................................................................................................................37
8.1Functional check for emergency shutdown module.....................................................................................38
9Specifications .............................................................................................................................................39
9.1TZIDC-200....................................................................................................................................................39
9.1.1Input ......................................................................................................................................................39

Contents
4 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
9.1.2Output ...................................................................................................................................................39
9.1.3Travel ....................................................................................................................................................39
9.1.4Air supply ..............................................................................................................................................39
9.1.5Transmission data and influences ........................................................................................................40
9.1.6Environmental capabilities ....................................................................................................................40
9.1.7Housing .................................................................................................................................................40
9.1.8Safety Integrity Level.............................................................................................................................40
9.1.9Options..................................................................................................................................................41
9.1.10Accessories...........................................................................................................................................42
9.2TZIDC-210....................................................................................................................................................42
9.2.1Communication .....................................................................................................................................42
9.2.2Description ............................................................................................................................................42
9.2.3Output ...................................................................................................................................................42
9.2.4Travel ....................................................................................................................................................42
9.2.5Air supply ..............................................................................................................................................42
9.2.6Transmission data and influences ........................................................................................................43
9.2.7Environmental capabilities ....................................................................................................................43
9.2.8Housing .................................................................................................................................................43
9.2.9Options..................................................................................................................................................44
9.2.10Accessories...........................................................................................................................................44
9.3TZIDC-220....................................................................................................................................................45
9.3.1Communication .....................................................................................................................................45
9.3.2Device name .........................................................................................................................................45
9.3.3Output ...................................................................................................................................................45
9.3.4Travel ....................................................................................................................................................45
9.3.5Air supply ..............................................................................................................................................45
9.3.6Transmission data and influences ........................................................................................................46
9.3.7Environmental capabilities ....................................................................................................................46
9.3.8Housing .................................................................................................................................................46
9.3.9Options..................................................................................................................................................47
9.3.10Accessories...........................................................................................................................................47
10Ex relevant specifications .........................................................................................................................48
10.1TZIDC-200....................................................................................................................................................48
10.1.1FM / CSA...............................................................................................................................................48
10.1.2ATEX / GOST Russia / GOST Ukraine.................................................................................................48
10.1.3IECEx ....................................................................................................................................................52
10.2TZIDC-210....................................................................................................................................................55
10.2.1FM / CSA...............................................................................................................................................55
10.2.2ATEX / GOST Russia / GOST Ukraine.................................................................................................55
10.2.3IECEx ....................................................................................................................................................58
10.3TZIDC-220....................................................................................................................................................60
10.3.1FM / CSA...............................................................................................................................................60
10.3.2ATEX / GOST Russia / GOST Ukraine.................................................................................................60
10.3.3IECEx ....................................................................................................................................................63
11Appendix .....................................................................................................................................................65
11.1Approvals and certifications .........................................................................................................................65

Safety
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 5
1 Safety
1.1 General information and notes for the reader
You must read these instructions carefully prior to installing and commissioning the device.
These instructions are an important part of the product and must be kept for future reference.
These instructions are intended as an overview and do not contain detailed information on all
designs for this product or every possible aspect of installation, operation and maintenance.
For additional information or if specific problems occur that are not discussed in these
instructions, contact the manufacturer.
The content of these instructions is neither part of any previous or existing agreement, promise
or legal relationship nor is it intended to change the same.
This product is built based on state-of-the-art technology and is operationally safe. It has been
tested and left the factory in perfect working order from a safety perspective. The information in
the manual must be observed and followed in order to maintain this state throughout the period
of operation.
Modifications and repairs to the product may only be performed if expressly permitted by these
instructions.
Only by observing all of the safety instructions and all safety/warning symbols in these
instructions can optimum protection of both personnel and the environment, as well as safe and
fault-free operation of the device, be ensured.
Information and symbols directly on the product must be observed. They may not be removed
and must be fully legible at all times.
1.2 Intended use
TZIDC-200, TZIDC-210, TZIDC-220 positioners are electro-pneumatic positioning devices for
use with pneumatically controlled actuators.
The device may only be used for the applications listed in these operating instructions and in
the data sheet.
• The maximum operating temperature must not be exceeded.
• The permissible operating temperature must not be exceeded.
• The housing protection type must be observed during operation.
1.3 Target groups and qualifications
Installation, commissioning, and maintenance of the product may only be performed by trained
specialist personnel who have been authorized by the plant operator to do so. The specialist
personnel must have read and understood the manual and comply with its instructions.
Prior to using corrosive and abrasive materials for measurement purposes, the operator must
check the level of resistance of all parts coming into contact with the materials to be measured.
ABB Automation Products GmbH will gladly support you in selecting the materials, but cannot
accept any liability in doing so.
The operators must strictly observe the applicable national regulations with regards to
installation, function tests, repairs, and maintenance of electrical products.

Safety
6 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
1.4 Warranty provisions
Using the device in a manner that does not fall within the scope of its intended use, disregarding
this instruction, using underqualified personnel, or making unauthorized alterations releases the
manufacturer from liability for any resulting damage. This renders the manufacturer's warranty
null and void.
1.5 Plates and symbols
1.5.1 Safety- / warning symbols, note symbols
DANGER – <Serious damage to health / risk to life>
This symbol in conjunction with the signal word "Danger" indicates an imminent danger.
Failure to observe this safety information will result in death or severe injury.
DANGER – <Serious damage to health / risk to life>
This symbol in conjunction with the signal word "Danger" indicates an imminent electrical
hazard. Failure to observe this safety information will result in death or severe injury.
WARNING – <Bodily injury>
This symbol in conjunction with the signal word “Warning“ indicates a possibly dangerous
situation. Failure to observe this safety information may result in death or severe injury.
WARNING – <Bodily injury>
This symbol in conjunction with the signal word "Warning" indicates a potential electrical
hazard. Failure to observe this safety information may result in death or severe injury.
CAUTION – <Minor injury>
This symbol in conjunction with the signal word “Caution“ indicates a possibly dangerous
situation. Failure to observe this safety information may result in minor or moderate injury.
This may also be used for property damage warnings.
NOTICE – <Property damage>!
The symbol indicates a potentially damaging situation.
Failure to observe this safety information may result in damage to or destruction of the product
and/or other system components.
IMPORTANT (NOTE)
This symbol indicates operator tips, particularly useful information, or important information
about the product or its further uses. It does not indicate a dangerous or damaging situation.

Safety
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 7
1.5.2 Name plate
Fig. 1: Name plate
1Complete model name
2Software version
3Serial number
4NL number
5Year
6

Supply pressure
7Input
8Output
9Dead
10Options
1.6 Transport safety information
Check the devices for possible damage that may have occurred during transport. Damages in
transit must be recorded on the transport documents. All claims for damages must be claimed
without delay against the shipper and before the installation.
1.7 Storage conditions
The unit must be stored in dry and dust-free conditions. The unit is also protected by a
dessicant in the packaging.
The storage temperature should be between -40 ... 85 °C (-40 ... 185 °F).
The storage time is basically indefinite. However, the warranty conditions stipulated in the order
confirmation of the supplier are valid.
M00406
Type: V18345 -
Softw.-Rev.:
Serial no./Seriennr.:
NL-No.:
Year/Baujahr:
Supplypress: 20 ... 90 psi
Zuluftdruck: 1,4 ... 6 bar
Input: analog 4 - 20 mA
Eingang:
TZIDC
Output / Ausgang:
Loss of electr. supply/ Stromlos:
Options/ Optionen
ABB Automation Products GmbH
Schillerstrasse 72
D - 32425 Minden
Made in Germany
0044
analog feedback
electr. limit switch
mech. limit switch
FSK
position indicator
safety shut down
1
2
3
4
5
8
9
10
6
7

Safety
8 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
1.8 Installation safety information
CAUTION - Risk of injury!
Incorrect parameter values can cause the valve to move unexpectedly. This can lead to
process failures and result in injuries.
Before recommissioning a TZIDC-200, TZIDC-210, TZIDC-220 positioner that was used at
another location, the device must always be reset to factory settings. Never start Autoadjust
before restoring factory settings.
• Only qualified specialists who have been trained for these tasks are authorized to mount and
adjust the unit, and to make the electrical connection.
• When working on the unit always observe the locally valid accident prevention regulations
and the regulations concerning the construction of technical installations.
1.9 Safety information for electrical installation
o
• The electrical connection may only be made by authorized specialist personnel and in
accordance with the electrical circuit diagrams.
• The electrical connection information in the manual must be observed; otherwise, the type of
electrical protection may be adversely affected.
• Safe isolation of electrical circuits which are dangerous if touched is only guaranteed if the
connected devices satisfy the requirements of DIN EN 61140 (VDE 0140 Part 1) (basic
requirements for safe isolation).
• To ensure safe isolation, install supply lines so that they are separate from electrical circuits
which are dangerous if touched, or implement additional isolation measures for them.
1.10 Operating safety information
Before switching on the unit make sure that your installation complies with the environmental
conditions listed in the chapter "Technical data" or in the data sheet.
If there is a chance that safe operation is no longer possible, take the unit out of operation and
secure against unintended startup.
When mounting the unit in areas that may be accessed by unauthorized persons, take the
required protective measures.
Prior to installation, check the devices for any damage that may have occurred as a result of
improper transport. Details of any damage that has occurred in transit must be recorded on the
transport documents. All claims for damages must be submitted to the shipper without delay
and before installation.

Safety
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 9
1.11 Returning devices
Use the original packaging or suitably secure shipping containers if you need to return the
device for repair or recalibration purposes. Fill out the return form (see the Appendix) and
include this with the device.
According to EC guidelines for hazardous materials, the owner of hazardous waste is
responsible for its disposal or must observe the following regulations for shipping purposes:
All devices delivered to ABB Automation Products GmbH must be free from any hazardous
materials (acids, alkalis, solvents, etc.).
Please
Please contact Customer Center Service acc. to page 2 for nearest service location.
1.12 Integrated management system
ABB Automation Products GmbH operates an integrated management system, consisting of:
• Quality management system to ISO 9001:2008
• Environmental management system to ISO 14001:2004
• Occupational health and safety management system to BS OHSAS 18001:2007 and
• Data and information protection management system
Environmental awareness is an important part of our company policy.
Our products and solutions are intended to have a minimal impact on the environment and on
people during manufacturing, storage, transport, use, and disposal.
This includes the environmentally-friendly use of natural resources. We conducts an open
dialog with the public through our publications.

Ex relevant safety instructions
10 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
1.13 Disposal
This product is manufactured from materials that can be reused by specialist recycling
companies.
1.13.1 Information on WEEE Directive 2002/96/EC (Waste Electrical and Electronic Equipment)
This product is not subject to WEEE Directive 2002/96/EC or relevant national laws
(e.g., ElektroG in Germany).
The product must be disposed of at a specialist recycling facility. Do not use municipal garbage
collection points. According to the WEEE Directive 2002/96/EC, only products used in private
applications may be disposed of at municipal garbage facilities. Proper disposal prevents
negative effects on people and the environment, and supports the reuse of valuable raw
materials.
If it is not possible to dispose of old equipment properly, ABB Service can accept and dispose of
returns for a fee.
1.13.2 RoHS Directive 2002/95/EC
With the Electrical and Electronic Equipment Act (ElektroG) in Germany, the European
Directives 2002/96/EC (WEEE) and 2002/95/EC (RoHS) are translated into national law.
ElektroG defines the products that are subject to regulated collection and disposal or reuse in
the event of disposal or at the end of their service life. ElektroG also prohibits the marketing of
electrical and electronic equipment that contains certain amounts of lead, cadmium, mercury,
hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers
(PBDE) (also known as hazardous substances with restricted uses).
The products provided by ABB Automation Products GmbH do not fall within the current scope
of the directive on waste from electrical and electronic equipment according to ElektroG. If the
necessary components are available on the market at the right time, in the future these
substances will no longer be used in new product development.
2 Ex relevant safety instructions
Depending on the type of explosion protection, an Ex label is attached to the left-hand side of
the positioner, next to the main name plate. It indicates the level of explosion protection and the
device's relevant Ex certificate.
Requirements/Preconditions for safe operation of positioners:
IMPORTANT (NOTE)
Observe the units' relevant technical data and special conditions in accordance with the
applicable certificate.
• Manipulation of the devices by users is not permitted. Modifications to the devices may only
be performed by the manufacturer or an explosion protection specialist.

Ex relevant safety instructions
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 11
• The splash guard cap must be screwed in place to achieve the IP 65 / NEMA 4x protection
class. Operating the devices without the splash guard cap is prohibited.
• The device may only be supplied with instrument air that is free of oil, water, and dust. Do
not use flammable gases, oxygen, or oxygen-enriched gas.
DANGER – Risk of explosion
Hot parts inside the housing may pose a risk of explosion.
Never open the device immediately after switch-off. Always wait at least four minutes before
opening the device.
• Prior to final installation, the owner must decide how the device is to be used, either
A) as a device featuring the intrinsically safe "Ex i" type of ignition protection, or
B) as a device with the "Ex d" type of ignition protection,
and he/she must mark the selected type of use on the name plate in a permanent manner.
Specific ambient conditions such as chemical corrosion should be taken into account when
affixing the permanent mark. Only the manufacturer may change the selected type of use
following a review.
• Variants that also meet the requirements for the "intrinsically safe" type of ignition protection
may not be used as "intrinsically safe", if they have been previously used as a flameproof
type of ignition protection.
• Secure the cable and line entries against twisting and becoming loose by applying adhesive
of medium strength.
• In the event of high torsional forces, the bearing sleeves on the shaft for the position pickoff
must be replaced due to wear (significant system deviation).
• If the positioner is used at an ambient temperature above 60 °C (140 °F) or below -20 °C
(-4 °F), use cable entries and lines approved for a service temperature corresponding to the
maximum ambient temperature increased by 10 K or corresponding to the minimum ambient
temperature, respectively.
NOTICE – Potential damage to parts
If the sealing surface is damaged, the "Ex d" explosion protection is no longer guaranteed.
Handle the housing cover carefully. Place the housing cover only on a smooth and clean
surface.
DANGER – Risk of explosion (TZIDC-200 only)
It is prohibited to use the local communication interface (LKS) in an explosion risk area.
Never use the local communication interface (LKS) on the main board with a positioner that is
being used in an explosion risk area.

Design and function
12 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
3 Design and function
Basic model Optional upgrades
Fig. 2: TZIDC-200, TZIDC-210, TZIDC-220 schematic diagram
Basic model Optional upgrades
1LKS plug 1)
2Setpoint signal 4 … 20 mA / bus connection
3Digital input 1)
4Digital output 1)
5Air supply, 1.4 …6 bar (20 … 90 psi)
6Exhaust
7I/P module with 3/3-way valve
8Position sensor (optional up to 270° rotation angle)
9

Plug module for analog feedback (4 … 20 mA) 1)
10Plug-in module for safety shutdown (forced depressurization)
11Plug module for digital feedback 1)
12Installation kit for mechanical position indicator
13Installation kit for digital feedback with proximity switches
14Installation kit for digital feedback with 24 V microswitches
1) TZIDC-200 only
IMPORTANT (NOTE)
With optional upgrades either the “Installation kit for digital feedback with proximity switches”
(13) or the “Installation kit for digital feedback with microswitches 24 V” (14) can be used.
In both cases, the “mechanical position indicator” (8) must be installed.
Functionality
TZIDC-200, TZIDC-210, TZIDC-220 positioners are electronically configurable positioners with
communication capabilities designed for mounting on pneumatic linear or rotary actuators.
Fully automatic determination of the control parameters and adaptation to the final control
element yield considerable time savings and an optimal control behavior.

Mounting
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 13
4 Mounting
CAUTION - Risk of injury!
Incorrect parameter values can cause the valve to move unexpectedly. This can lead to
process failures and result in injuries.
Before recommissioning a TZIDC-200, TZIDC-210, TZIDC-220 positioner that was used at
another location, the device must always be reset to factory settings. Never start Autoadjust
before restoring factory settings.
4.1 Operating conditions at installation site
IMPORTANT (NOTE)
Before installation, check whether the TZIDC-200, TZIDC-210, TZIDC-220 positioner meets
the control and safety requirements for the installation location (actuator or valve).
See chapter Specifications page 39.
4.2 Mechanical mount
cke
4.2.1 General information
Fig. 3: Operating range
The arrow (1) on the positioner feedback shaft (and hence the lever) must move through the
area marked by the arrows (2).

Mounting
14 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
M00410
12
3
4
+30°+60°
-60°
-30°
+100%
+100%
0%
0%
TZID-C
Fig. 4: Sensor range
1 Sensor range for linear actuators
2 Sensor range for part-turn actuators
3 Restricted operating range
4 Operating range
IMPORTANT (NOTE)
During installation make sure that the actuator travel or rotation angle for position feedback is
implemented correctly.
The maximum rotation angle for position feedback is 60° when installed on linear actuators and
120° on part-turn actuators. The minimum angle is always 25°.

Mounting
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 15
4.2.2 Mounting on linear actuators
For mounting on a linear actuator in accordance with DIN / IEC 534 (lateral mount per NAMUR)
a complete mounting kit is available, and consists of the items in the following table:
Fig. 5: Mounting kit for linear actuators
• Lever (4) with follower pin, for stroke adjustment 10 ... 35 mm (0.39 ... 1.38 inch) or
20 ... 100 mm (0.79 ... 3.94 inch).
• Follower guide (13) with two screws (10), spring washers (11), and clamp plates (12).
• Mount bracket (3) with two screws (6) and two shims (5).
• Screw (1) and shim (2) for mounting on cast iron yoke.
• Two U-bolts (7) each with two shims (8) and two nuts (9) for mounting on columnar yoke.
Required tools:
- Wrench, size 10 / 13
- Allen key, size 4

Mounting
16 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
Procedure:
1. Attaching follower guide to actuator
Fig. 6
IMPORTANT (NOTE)
Hand tighten the screws.
• Attach the follower guide (1) and clamp plates (2) with screws (4) and spring washers (3) to
the actuator stem.
2. Assemble the lever (unless preassembled)
Fig. 7
• Insert spring (8) on bolt with follower pin (9).
• Slip the plastic washer (7) onto the bolt and compress the spring with it.
• Insert the bolt with compressed spring into the oblong hole in the lever (6) and fasten it in the
desired position using the plain washer (5) and nut (4) at the lever. The scale on the lever
indicates the link point for the stroke range.
• Place the washer (2) on the screw (1). Insert the screw in the lever and lock with the nut (3).

Mounting
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 17
3. Mounting lever and bracket on positioner
Fig. 8
• Attach the lever (6) to the feedback shaft (5) of the positioner (can only be mounted in one
position due to the flat on the side of the shaft).
• Using the arrow marks (4) check whether the lever moves within the operating range
(between the arrows).
• Hand-tighten the screw (7) on the lever.
• Hold the prepared positioner with loose mount bracket (1) to the actuator so that the follower
pin for the lever enters the follower guide to determine which holes on the positioner must be
used for the mount bracket.
• Attach the mount bracket (1) with screws (2) and shims (3) to the proper holes on the
positioner housing. Tighten the screws as evenly as possible to ensure subsequent linearity.
Align the mount bracket in the oblong hole to ensure that the operating range is symmetrical
(lever moves between the arrows (4)).

Mounting
18 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
4.a Mounting on cast iron yoke
Fig. 9
• Attach the mount bracket (2) with screw (4) and shim (3) to the cast iron yoke (1)
or
4.a Mounting on columnar yoke
Fig. 10
• Hold the mount bracket (3) in the proper position on the columnar yoke (3).
• Insert the U-bolts (2) from the inside of the columnar yoke (3) through the holes for the
mount bracket.
• Add the washers (5) and nuts (6). Hand tighten the nuts.
IMPORTANT (NOTE)
Adjust the height of the positioner on the cast iron yoke or columnar yoke until the lever is
horizontal (based on visual check) at half stroke of the valve.

Mounting
42/18-85-EN TZIDC-200, TZIDC-210, TZIDC-220 19
Fig. 11: Linkage for positioner
1larger 2

smaller
The scale on the lever indicates the link points for the various stroke ranges of the valve.
Move the bolt with the follower pin in the oblong hole of the lever to adjust the stroke range of
the valve to the working range for the position sensor.
Moving the link point inwards increases the rotation angle of the sensor. Moving the link point
outwards reduces the rotation angle of the sensor.
Adjust the actuator stroke so that you can make use of as large an angle of rotation as possible
(symmetrical around the center position) on the position sensor.
Recommended range for linear actuators: between -28 ... 28°
Minimum angle: 25°
IMPORTANT (NOTE)
After mounting, check whether the positioner is operating within the sensor range.

Mounting
20 TZIDC-200, TZIDC-210, TZIDC-220 42/18-85-EN
4.2.3 Mounting on part-turn actuator
For mounting on part-turn actuators in accordance with VDI / VDE 3845, the following mounting
kit is available:
Fig. 12
• Adapter (1) with spring (5).
• Four screws M6 (4), four spring washers (3), and four shims (2) for attaching the mounting
bracket (6) to the positioner.
• Four screws M5 (7), four spring washers (8), and four shims (9) for attaching the mounting
bracket to the actuator.
Required tools:
- Wrench, size 10 / 13
- Allen key, size 3