Abloy PLK/A1 User manual

14.1.2020 Rev.1
PLK/A1
Instructions for use
An ASSA ABLOY Group brand
Color Basic purpose
GREEN Indicates success
RED Indicates failure
WHITE Awake and not connected
BLUE Awake and connected
Function Color Indication
Wakeup, not connected WHITE Lit for 1 second
Wakeup, connected BLUE Lit for 1 second
Awake, not connected WHITE Blinking with 50ms on 950ms off cycle
Awake, connected BLUE Blinking with 50ms on 950ms off cycle
Battery poor RED Additional blink for 50ms after awake indication
Motor drive success (access granted) GREEN Lit for 2 seconds
Motor drive fail (access granted) RED Lit for 2 seconds
Going to sleep WHITE Blinking with 50ms on 150ms off for 1 second
The specs
Certifications
Lock and unlock the
padlock a couple of
times so the firmware
checks the new battery
status.
2,5 mm
LED indiations
Changing the battery
123
4 5
• Shackle diameter: 10 mm
• Security grading: EN 16864:2017 11440D34
classification
• Battery types:
For cold environment: Panasonic CR2
For warm environment: Saft LS14250 (use adapter)
CAUTION Risk of explosion if the battery is replaced by
an incorrect type
• Battery life: 5 years / 5000 openings
•Operating temperature: -25 +60
• Compatibility: Android devices with BT 4.0 and Android
version 4.4 or newer
•The USB-C port is for service use only. If the battery is
completely discharged, use the USB power bank
(5Vdc 500mA) as backup power.
x2
3 mm
FCC ID: 2AI5J-PLKA1

USB-C
Backup power
An ASSA ABLOY Group brand
Compliance information
EU
EC DECLARATION OF CONFORMITY (DoC)
Abloy Oy (PO BOX 108, FI-80101 JOENSUU, FINLAND) declare under our sole of responsibility that the ABLOY PLK/A1 fulfills the directive RE
2014/53/EU asfollows: Standards: EN 62368-1:2014 (2.ed), EN 60950-22:2006/AC:2008, EN 301 489-01:V2.2.3, EN 301 489-17:V3.2.2, EN 300
328 v2.2.2 EN IEC 61000-6-2:2019, EN 61000-6-3:2007 + A1:2011 Joensuu xx.xx.2020 ______________________________________
USA
Any changes or modifications to this equipment that are not approved by Abloy may void the user’s authority to operate the equipment. This device
complies with part 15 C of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This portable device with its antenna complies with FCC RF exposure limits for general population / uncontrolled exposure. The antenna used for this
device must not be co-located or operating in conjunction with any other antenna or transmitter.