ACME E-40D TC DXX User manual

E-40D TC DXX
User Manual

Feature:
E-40D TC is DMX Version, Uniform light, sharp image edge, and
self-locking focus lens. The product takes advantage of the heat pipe
heat conduction and housing feature to dissipate heat without fan to
prolong LED life.
Light Source: 1 x 20W RGB LED
Color temperature:2800±150K
6000±150K
Beam Angle: 19°/26°/36°/50°
Specification:
Power Voltage: AC 100~240V,50/60Hz
Power Consumption: 32W
Weight: 1.6Kgs
Dimension: 273 x 244 x 140 mm
244
273
140
1B

How To Change The Gobo
At first, put the gobo by hand as the arrow into the gobo gel splint,
and insert the gobo gel splint into the slot of the unit, please turn
the hand knob to left or right in order to take out gobo gel splint.
Main Function
To select any of the given functions, press the MENU button up to
when the required one is showing on the display. Select the function
by ENTER button and the display will blink. Use the DOWN/UP
button to change the mode. Once the required mode has been
selected, press the ENTER button to setup, to go back to the
functions without any change press the MENU button again. Hold
and press the MENU button about one second or wait for one
minute to exit the menu mode.
The main functions are showing below:
2B

DMX Address
Press the MENU button up to when the is shown on the
display. Pressing ENTER button and the display will blink. Use DOWN
and UP button to change the value from 1to 512. Once the mode
MENU
DMX Address
Channel Mode
DMX State
Led
Display Inversion
Auto Test
Fixture Hours
Software Version
Dimmer Mode
Manual Mode
White Balance
3B

has been selected, press the ENTER button to setup, to go back to
the functions without any change press the MENU button again.
Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
Channel Mode
Press the MENU button to show on the display. Press the
ENTER button and the display will blink. Use the DOWN and UP
button to select the 1ch, 2ch, 3ch or 8ch. Once the mode has been
selected, press the ENTER button to setup, to go back to the
functions without any change press the MENU button again. Hold
and press the MENU button about one second or wait for one
minute to exit the menu mode.
DMX State
Press the MENU button up to when the is shown on the
display. Pressing ENTER button, Use DOWN and UP button to select
the (blackout mode)or (last state). Once the mode
has been selected, press the ENTER button to setup, to go back to
the functions without any change press the MENU button again.
Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
4B

Dimmer Mode
Press the MENU button up to when the is shown on the
display. Pressing the ENTER button. Use DOWN and UP button to
select the (dimmer 1), (dimmer 2), (dimmer
3) or (dimmer 4). Once the mode has been selected, press
the ENTER button to setup, to go back to the functions without any
change press the MENU button again. Hold and press the MENU
button about one second or wait for one minute to exit the menu
mode.
Mode 1(Optically Linear):
The increase in light intensity appears to be linear as DMX value is
increased.
Mode 2(Square Law):
Light intensity control is finer at low levels and coarser at high levels.
Mode 3(Inverse Square Law):
Light intensity control is coarser at low levels and finger at high
levels.
Mode 4(S-cure):
5B

Light intensity control is finger at low levels and high levels and
coarser at medium levels.
LED
Press the MENU button up to when the is shown on the
display. Pressing ENTER button and the display will blink. Use DOWN
and UP button to select (On) or (Off), Once the
mode has been selected, press the ENTER button to setup, to go
back to the functions without any change press the MENU button
again. Hold and press the MENU button about one second or wait
for one minute to exit the menu mode.
Display Inversion
Press MENU button until is blinking on the display. Use the
DOWN and UP button to select (normal) or (inverse),
Once the mode has been selected, press the ENTER button to setup,
to go back to the functions without any change press the MENU
button again. Hold and press the MENU button about one second or
wait for one minute to exit the menu mode.
White Balance
Press the MENU button up to when the is shown on the
display. Pressing ENTER button and the display will blink. Use DOWN
and UP button to select (red), (green),
6B

(blue), ,Once the mode has been selected, press the ENTER button
to setup the value from 125 to 255, to go back to the functions
without any change press the MENU button again. Hold and press
the MENU button about one second or wait for one minute to exit
the menu mode.
Manual Mode
Press the MENU button up to when the is shown on the
display. Pressing ENTER button and the display will blink. Use DOWN
and UP button to select (red), (green), (blue),
(dimmer), (strobe),Once the mode has been selected,
press the ENTER button to setup the value from 0to 255, to go back
to the functions without any change press the MENU button again.
Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
Auto Test
Press the MENU button up to when the is blinking on the
display. Press the ENTER button and the unit will run the built-in
programmer for self-test. To go back to the functions press the
MENU button.
Fixture Hours
7B

Press the MENU button up to when the is blinking on the
display. Press the ENTER button and the display will show the
temperature of the unit. To go back to the functions press the MENU
button.
Software version
Press the MENU button up to when the is blinking on the
display. Press the ENTER button and the display will show the version
of software of the unit. To go back to the functions press the MENU
button.
DMX Controller
By using a universal DMX controller to control the units, you will
need to set DMX address from 1 to 512 so that the units can receive
DMX signal.
Press the MENU button up to when the DMX Address is showing on
the display. Pressing the ENTER button and the display will blink. Use
the DOWN/UP button to change the DMX512 address. Once the
address has been selected, press the ENTER button to setup, to go
back to the functions without any change press the MENU button
again. Hold and press the MENU button about one second or wait
for one minute to exit the menu mode.
Please refer to the following diagram to address your DMX512
8B

channel for the first 4 units：
Channel
mode
Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
1 channels
1
2
3
4
2 channels
1
3
5
7
3 channels
1
4
7
10
8 channels
1
9
17
25
DMX 512 Configuration
1 CH MODE (MODE 1):
CHANNEL VALUE FUNCTION
1
000-007
008-034
035-061
062-088
089-115
116-142
143-169
170-196
197-223
MACRO
Close
2800K
3200K
3600K
4000K
4400K
4800K
5200K
5600K
9B