ACR Electronics GlobalFix V5 Category 1 AIS EPIRB User manual

English
EMERGENCY POSITION INDICATING RADIO BEACON
WITH AIS AND RLS
Models Covered
• GlobalFix V5 Category 1 AIS EPIRB
• GlobalFix V5 Category 2 AIS EPIRB
USER MANUAL

GlobalFix V5 User Manual
2 912S-04064 - 01.02 15/11/2022
© 2022 ACR Electronics Inc.
The technical data, information and illustrations contained in this manual were believed to
be correct at the time of print. ACR Electronics Inc. reserve the right to change specifica-
tions and other information contained in this manual as part of our continual improvement
process.
No part of this manual may be reproduced, stored in a retrieval system or transmitted in
any form, electronic or otherwise, without the prior permission of ACR Electronics Inc.
No liability can be accepted for any inaccuracies or omissions in this manual.
GlobalFix® is a registered trademarks of ACR Electronics Inc.
For ease of access please record details of your GlobalFix V5 here:
Owners Name: .......................................................
Vessel Name: .......................................................
Beacon HEX ID (UIN): .......................................................

15/11/2022 912S-04064 - 01.02 3
GlobalFix V5 User Manual
USE ONLY IN SITUATIONS OF GRAVE AND IMMINENT DANGER
DEPLOYING YOUR BEACON
IN CASE OF EMERGENCY
Category 1 (Automatic or Manual Deployment) Category 2 (Manual Deployment Only)
OR
IN A NON-EVACUATION EMERGENCY - THE BEACON CAN ALSO BE MANUALLY DEPLOYED FROM
EITHER BRACKET AND MANUALLY ACTIVATED USING THE ON/OFF KEY
ACTIVATING YOUR BEACON
Manual Activation Water Activation
OR
Attach the beacon to your wrist, life
jacket or life raft using the lanyard.
DO NOT attach the beacon to a sinking or
abandoned vessel.
The white strobe will start flashing as
an indication of activation.
Refer to page 15 for full LED indications.
WATER ACTIVATION
EPIRB MUST BE REMOVED
FROM BRACKET AND IN THE WATER

GlobalFix V5 User Manual
4 912S-04064 - 01.02 15/11/2022
1. ABOUT YOUR EPIRB
1.1 COSPAS/SARSAT System
The basic Cospas-Sarsat concept is illustrated in the figure below.
The System is composed of:
• distress radio beacons (ELTs for aviation use, EPIRBs for maritime use, and
PLBs for personal use) which transmit signals during distress situations
• instruments on board satellites in geostationary and low-altitude Earth
orbits which detect the signals transmitted by distress radio beacons
• ground receiving stations, referred to as Local User Terminals (LUTs), which
receive and process the satellite downlink signal to generate distress alerts
• Mission Control Centers (MCCs) which receive alerts produced by LUTs and
forward them to Rescue Coordination Centers (RCCs), Search and Rescue
Points Of Contacts (SPOCs) or other MCCs
The Cospas-Sarsat System includes two types of satellites:
• satellites in low-altitude Earth orbit (LEO) which form the LEOSAR System
• satellites in geostationary Earth orbit (GEO) which form the GEOSAR System
The future Cospas-Sarsat System will include a new type of satellite in the medium-al-
titude Earth orbit (MEO) which will form the MEOSAR System. The GlobalFix V5 is fully
compatible with the new MEOSAR satellites.

15/11/2022 912S-04064 - 01.02 5
GlobalFix V5 User Manual
1.2 Return Link Service
The Galileo Return Link Service (RLS) is a free-of-charge global service available to
Cospas-Sarsat RLS compatible beacons. The new functionality, currently offered uniquely
by Galileo, enables a communication link that relays a Return Link Message (RLM) back to
the originating beacon through the Galileo Navigation Signal in Space.
The RLS feature is an indication on the GlobalFix V5 that confirms to the User that the
distress signal from the EPIRB has been localised by the Cospas-Sarsat system and is
being sent to the SAR authorities. It does NOT mean that a search and rescue mission has
been launched, but only confirms that the distress alert has been received by the Cospas-
Sarsat system and is being routed to the appropriate SAR agencies. The RLS will send an
acknowledgment to the beacon less than 30 minutes following activation (usually much
quicker). RLS is an optional function and may not be permitted in all countries. The full
RLS specification can be found here:
https://gsc-europa.eu/sites/default/files/sites/all/files/Galileo-SAR-SDD.pdf
1.3 AIS System
AIS systems operate on VHF radio bands and transceivers are fitted to all commercial
shipping and an ever growing number of recreational vessels globally. Shortly after
activation, an AIS EPIRB device will activate an alarm on all AIS equipped vessels within
VHF range alerting them to the fact that a person is in the water needing assistance. Often
it is a vessel in the close vicinity of an incident that is able to react and effect a rescue
quicker than the emergency services.
Emergency service craft are fitted with AIS
receivers allowing them to pinpoint a casualty in
the water more precisely than any other system.
1.4 The GlobalFix Range
1.4.1 GlobalFix V5 Category 1 (Part No. 2851)
This EPIRB combines 406MHz Cospas-Sarsat distress beacon with RLS and AIS transmitter
in a Category 1 Auto Release Housing. This unit complies with IMO resolution MSC.471
(101) for commercial vessels and will auto-activate in contact with the water.
1.4.2 GlobalFix V5 Category 2 (Part No. 2852)
1.4.3 This EPIRB combines 406MHz Cospas-Sarsat distress beacon with RLS and AIS
transmitter in a Category 2 Manual Release Bracket. This unit complies with IMO resolu-
tion MSC.471 (101) for commercial vessels and will auto-activate in contact with the water.

GlobalFix V5 User Manual
6 912S-04064 - 01.02 15/11/2022
1. ABOUT YOUR EPIRB 4
1.1 COSPAS/SARSAT System 4
1.2 Return Link Service 5
1.3 AIS System 5
1.4 The GlobalFix Range 5
2. GENERAL 7
2.1 Introduction 7
2.2 Exposure to RF Electromagnetic Energy 7
2.3 Warnings 7
2.4 What’s in the Box 8
2.5 Operating Modes 8
3. GLOBALFIX V5 OVERVIEW 9
4. INSTALLATION 10
4.1 Location 10
4.2 Removal from and Re-fitting to the Automatic Release Housing 10
4.3 Manual Mounting Bracket - Removal and Re-fitting 12
4.4 Fit the Manual Mounting Bracket 12
5. OPERATION 13
5.1 Manual Release 13
5.2 Optical Indications on activation 15
5.3 Deactivation 16
6. FALSE ALERTS 16
7. TESTING 17
7.1 NFC and Mobile App. 17
7.2 Beacon Test 18
7.3 GNSS Test 19
8. BEACON REGISTRATION 20
8.1 Advice to owners of EPIRBs 20
8.2 Country Specific Registration Information 20
8.3 UNREGISTERED BEACON 21
9. APPENDIX 21
9.1 Maintenance and Troubleshooting 21
9.2 Batteries 22
9.3 Decommissioning and Disposal 23
9.4 Transport 23
9.5 HydroFix HRU Replacement 24
9.6 Specifications 25
9.7 Approvals 26
9.8 Spares 26
10. WARRANTY INFORMATION 27
10.1 Limited Warranty 27
10.2 Extended Warranty 27

15/11/2022 912S-04064 - 01.02 7
GlobalFix V5 User Manual
2. GENERAL
2.1 Introduction
This manual provides valuable information for the installation, operation and routine
maintenance of the GlobalFix V5.
Please read this manual completely before using your GlobalFix V5.
2.2 Exposure to RF Electromagnetic Energy
This product complies with EN62479 (EU) and RSS-102 (Canada).
2.3 Warnings
!It is a legal requirement to register your GlobalFix V5 with your National
Authority.
!Only use your GlobalFix V5 in a situation of grave and imminent danger.
!Deliberately misusing your GlobalFix V5 or setting it off accidentally may result in
prosecution and a fine.
!Contains Lithium batteries:
- store between -30°C (-22ºF) to+70°C (+158ºF)
If the GlobalFix V5 is stored at higher temperatures the battery life may
be degraded and should be replaced earlier than the date stated. Failure
to do this may result in the GlobalFix V5 fulfilling the stated 48hr
operating life. The effect is more pronounced as the temperature
increases.
- DO NOT ATTEMPT TO REPLACE THE BATTERIES YOURSELF
unauthorised opening and battery replacement may put
your life at risk.
- do not short circuit, incinerate or recharge.
!Please see section 9.4 for information on safe transportation.
!The battery in your GlobalFix V5 should be replaced immediately if it has been
activated, or if the test indicator shows the battery as ‘used’, or if the expiry date
marked on the unit has been exceeded.
!Battery replacement must be carried out at an ACR authorised battery
replacement centre using manufacturer supplied battery components. The
GlobalFix V5 Category 1 is supplied with an automatic release housing for
external installation only. See the installation guidelines in section 4 for further
information.
!Please read these instructions carefully. Failure to follow the guidance in this
manual may result in loss of warranty.

GlobalFix V5 User Manual
8 912S-04064 - 01.02 15/11/2022
2.4 What’s in the Box
1. Mounting Bracket
(see options)
2. GlobalFix V5
3. User Guide&
Labels pack
4. Mounting Screws
(x3 for Cat 2)
(x6 for Cat 1)
2.5 Operating Modes
Your GlobalFix V5 may be operated in a variety of modes.
2.5.1 Automatic activation
Should the vessel be in danger of sinking the GlobalFix V5 should
be removed from its bracket and placed in the sea. Contact with
the water will automatically activate the GlobalFix V5
2.5.2 Manual activation on deck
When deploying the GlobalFix V5 on a deck, ensure it is vertical
and clear of obstructions that might impede a clear view of
the sky. If the unit is thrown into the water then it will activate
automatically.
2.5.3 Manual activation in a life raft
The GlobalFix V5 may be deployed in a life-raft, where it should
be held in a vertical position so that there is a clear view of the
sky, preferably outside of the canopy. The GlobalFix V5 can also be
tethered to the life-raft and allowed to float alongside.
1
2
3

15/11/2022 912S-04064 - 01.02 9
GlobalFix V5 User Manual
!The lanyard is provided to attach the GlobalFix V5 to the life raft or your person,
once it is activated. Do not use it to attach it to the vessel, as this may result in
the loss of the GlobalFix V5 if the vessel sinks.
!It is important that the vessel details are marked on the GlobalFix V5. Please use
a fine tip UV resistant indelible pen to clearly mark the MMSI, Vessel Name and
Call Sign in the spaces provided. Cover this label with the clear protective label
provided to protect the text from wear.
1
2
34
6
8
1) ON/OFF Key (Under flap)
2) Indicator LED
3) Antenna
4) Strobe light (internal)
5) TEST Key
6) NFC Antenna
7) Witness Label
8) Lanyard under rubber band
9) Programming Details Label
(behind)
10) Category 1 Bracket
11) Category 2 Bracket
3. GLOBALFIX V5 OVERVIEW
5
7
10 11
9

GlobalFix V5 User Manual
10 912S-04064 - 01.02 15/11/2022
4. INSTALLATION
!Failure to follow the following installation guidelines may cause the GlobalFix V5
to operate incorrectly.
!Do not mount the GlobalFix V5 closer than 1.0 metre to any steering compass as
this may affect the accuracy of the compass.
!Keep the GlobalFix V5 away from any strong magnetic sources such as
loudspeakers, compass compensation magnets, etc.
!Do not install or operate in a location subject to high intensity RF fields (e.g.radar
or communications antennas)
!GNSS operation may be impaired if operated within 10m of GMDSS sat-com
systems.
4.1 Location
The location selected must be sufficiently robust to support the weight of the entire unit.
Exposure to the elements and surrounding hazards along with vibration should also be
taken into consideration when choosing the location. Ensure that the mounting location
allows easy access to the GlobalFix V5 for emergency use, maintenance and servicing.
Ensure that a Category 1 housing is installed to a
vertical surface where the beacon can float free
from the sinking vessel.
4.2 Removal from and Re-fitting to
the Automatic Release Housing
To access the bracket’s five pre-drilled mounting
holes, remove the bracket’s lid by turning the
spring loaded knob on the lid 1/4 turn counter
clockwise and pulling. The lid will lift away from
the top of the base and disengage at the bottom
of the base. The lid is tethered to the base to
help prevent loss. (If this tether is somehow
broken off, please have it replaced to prevent the
inadvertent loss of the top cover.)
Pull the beacon with steady pressure from the bracket. For normal use situations, four of
the five holes can be used to mount the bracket. It is therefore not necessary to remove the
HydroFix HRU to mount the bracket using all five holes.

15/11/2022 912S-04064 - 01.02 11
GlobalFix V5 User Manual
For extreme use situations, remove the HydroFix HRU and deploy the ejector spring for
access to the fifth mounting hole.
Hold the bracket in place to mark the screw holes or use the provided mounting template.
The use of #10 pan head stainless steel fasteners [minimum of ½” (1.27 cm) long] and #10
½” (1.27 cm) washers is recommended.

GlobalFix V5 User Manual
12 912S-04064 - 01.02 15/11/2022
4.3 Manual Mounting Bracket - Removal and Re-fitting
1) Press the tab marked PUSH to release the GlobalFix
V5 from the Manual Bracket.
2) Place the antenna into the slot on the bracket and insert
the top of the GlobalFix V5 into the bracket. Push the
bottom into the bracket until a click is heard
4.4 Fit the Manual Mounting Bracket
Using the dimensions shown, use the three No10 x 1” screws supplied to secure the
Manual Bracket to a suitable bulkhead in a position that will allow easy access in the event
of abandoning the vessel.
!Always install the manual mounting bracket inside the vessel to prevent the
EPIRB being dislodged and activated in heavy seas.

15/11/2022 912S-04064 - 01.02 13
GlobalFix V5 User Manual
5. OPERATION
The GlobalFix V5 is designed for best operation while floating in water. If used in other
situations ensure that the GlobalFix V5 is placed in the open, clear of any cover and kept
upright. Do not place the GlobalFix V5 close to large structures or under cover.
In the event of the vessel starting to sink the GlobalFix V5 Category 2 EPIRB MUST be
released from the Manual Bracket and placed in the water, it will activate on contact with
the water. The GlobalFix V5 Category 1 unit will auto deploy in the event of the vessel
sinking.
In the case of abandoning a ship, if possible, recover the GlobalFix V5 and tie to the survival
craft or person using the lanyard. For optimum operation, it is recommended that the
GlobalFix V5 be tied to a life-raft with the lanyard and floated in the sea.
!The GlobalFix V5 is prevented from auto activation while mounted in the Manual
Bracket or Automatic Release Housing. For activation the GlobalFix V5 MUST be
removed from either bracket allowing the antenna to deploy fully.
5.1 Manual Release
5.1.1 Remove from the Manual Bracket
• Press the tab marked PUSH and
pull the GlobalFix V5 EPIRB away
from the bracket
• Release the lanyard and attach it
securely to yourself or the life-raft
!DO NOT ATTACH THE BEACON
TO THE VESSEL AS THIS MAY SINK
SUBMERGING THE BEACON OR YOU
MAY DRIFT AWAY FROM THE
VESSEL
IN CASE OF EMERGENCY
USE ONLY IN SITUATIONS OF
GRAVE AND IMMINENT DANGER

GlobalFix V5 User Manual
14 912S-04064 - 01.02 15/11/2022
5.1.2 Lift the red flap breaking the witness seal
!DO NOT LEAVE THE BEACON IN THE
CATEGORY2 BRACKET IF THE VESSEL
IS IN DANGER OF SINKING
5.1.3 Press and hold the red button for 1 to 2 seconds to activate.
(Until the green LED starts to flash)
The GlobalFix V5 will now be operational. The strobe lights will begin to flash at a rate of
once every 2.5 seconds as soon as the unit is activated.
For best performance it is important that the GlobalFix V5 is in an upright position with a
clear view of the sky and as far away from any metallic structures as possible.
The GlobalFix V5 contains a GNSS receiver. Ensure that the GNSS antenna is not obstructed
and has a complete, unobstructed view of the sky – as indicated on the top of the GlobalFix
V5.
A lanyard is provided to tether the GlobalFix V5 to the lifeboat or life raft to ensure that it
does not drift away. Make sure this is firmly attached.
5.1.4 GlobalFix V5 Automatic Operation
The GlobalFix V5 will sense when it has been placed in water and automatically begin to
operate after a short delay, in the same manner as described above.
!If the GlobalFix V5 is mounted in the Manual Bracket or Auto Release Housing this
function is disabled until the GlobalFix V5 has been released.

15/11/2022 912S-04064 - 01.02 15
GlobalFix V5 User Manual
5.2 Optical Indications on activation
• The LED will illuminate green (blue if RLS is enabled) for 1 second.
• The strobe light will start flashing.
• Within 1 minute* of activation, the indicator LED will flash a quick burst of 5
indicating 406MHz transmission.
• Following the first 406MHz transmission the LED will flash 8 times** (green
if a GNSS fix has been acquired or red if there is no fix) indicating AIS
transmission.
5.2.1 LED Indications with RLS Enabled
LED When Transmit GNSS RLS
(x1) Every 5 s Searching
(x3) Once Fix acquired
(x5) At transmit 406MHz No Fix Request sent
(x5) At transmit 406MHz Fix acquired Request sent
(x8) At transmit* AIS No Fix
(x8) At transmit* AIS Fix acquired
(x1) Every 2.5 s** 121MHz Reply not received
(x1) Every 2.5 s** 121MHz Reply received
(x1) Every 2.5 s
5.2.2 LED Indications for units configured with non-RLS Protocol
LED When Transmit GNSS
(x1) Every 5 s Searching
(x3) Once Fix acquired
(x5) At transmit 406MHz No Fix
(x5) At transmit 406MHz Fix acquired
(x8) At transmit* AIS No Fix
(x8) At transmit* AIS Fix acquired
(x1) Every 2.5 s** 121MHz
(x1) Every 2.5 s
* The AIS transmissions will show as 8 flashes (1 every 2 seconds) as a sequence
repeated once every minute
** The 121MHz Homer will not transmit until after the first 406MHz transmission.

GlobalFix V5 User Manual
16 912S-04064 - 01.02 15/11/2022
5.3 Deactivation
5.3.1 Deactivation if Manually Activated
If the GlobalFix V5 has been inadvertently activated or the emergency situation has passed,
it can be turned off simply by pressing and holding for 1 to 2 seconds the ON/OFF key. It
is not possible for the user to replace the red protective cover. Return the GlobalFix V5 to an
ACR authorised service centre for checking and replacement.
5.3.2 Deactivation if Automatically Activated
If the GlobalFix V5 was automatically activated by placing in water, remove from the water
and dry. The GlobalFix V5 will automatically switch off after approximately 30 seconds.
6. FALSE ALERTS
False alerts are a serious problem - they cause valuable resources to be diverted away
from real emergency situations. If a false alert is initiated, by any means, it is important to
contact the nearest search and rescue authority and inform them of the false alert.
Report the following information:
1. GlobalFix V5 UIN.
2. Date, time and duration.
3. Cause of activation.
4. Location when the alert was activated.
5. Location at time of deactivation.
If the GlobalFix V5 was activated by mistake then turn it off. The first emergency trans-
mission will not occur for approximately 50 seconds. If the unit is turned off within this time
then GlobalFix V5 will not have sent an emergency distress alert.
The GlobalFix V5 is fitted with water activation contacts. Although the float free housing is
designed to prevent accidental activation in heavy seas and adverse weather conditions,
if the GlobalFix V5 is not correctly fitted in its housing it is possible that this may cause a
false alert situation.
If the unit has been dropped into the water then remove from the water and dry the case.
Wait approximately 30 seconds for the water contacts to de-activate. If the unit is still
flashing after this period, check that the unit has not been manually activated; if so then
follow the procedure to manually switch the GlobalFix V5 off.
Once the GlobalFix V5 is switched off, it is advisable to carry out a self test before replacing
the GlobalFix V5 into the Float Free Housing or Manual Bracket.
!Should the GlobalFix V5 fail to deactivate, bend the antenna down and completely
wrap in several layers of aluminum foil , or place in a metal container with a
tightly fitting lid.

15/11/2022 912S-04064 - 01.02 17
GlobalFix V5 User Manual
7. TESTING
Routine testing of your GlobalFix V5 is recommended to ensure it is in good working order
if needed in an emergency. Monthly testing is recommended, but remember that each test
will reduce the battery capacity slightly and reduce the operating time of your GlobalFix V5
during an emergency.
7.1 NFC and Mobile App.
The GlobalFix V5 is capable of connection to devices using Near Field Communication
(NFC). NFC technology allows communication between two electronic devices over a
distance of 4cm (1.5”) or less. The benefit of using NFC in the GlobalFix V5 is that the power
used for communication comes from the mobile device and not the beacon.
The ACR Mobile App allows a user to access the GlobalFix V5 and see the programmed
details and the latest test results giving a clear indication of the beacon’s condition.
Download the App. here: Android iOS
To use the App touch your mobile device to the top of the GlobalFix V5 where you see
“NFC”.

GlobalFix V5 User Manual
18 912S-04064 - 01.02 15/11/2022
7.2 Beacon Test
!Ensure the antenna is free and above the GlobalFix V5 before commencing the
test. Fold the antenna back behind the EPIRB as you replace it in the housing.
!Because the test transmits a short burst on the aircraft distress frequency of
121.5MHz, please only carry out this test in the first five minutes of each hour.
!It is recommended to test your GlobalFix V5 once a month.
!A magenta or amber test result indicates the battery has been used for over two
hours or the recommended number of tests has been exceeded. The GlobalFix
V5 will still operate normally in distress, but the battery should be replaced to
ensure the full operating life when your GlobalFix V5 is needed.
7.2.1 Functional Test
To test your GlobalFix V5 is functioning correctly, press and hold the TEST key for 1 to 2
seconds. The LED will illuminate red to indicate the key has been pressed, then start
flashing. Release the TEST key now. After a short pause the strobe will flash and
the indicator LED will produce a flash sequence.
The flash sequence indicates the total number of hours that the battery has already been in
use, up to the time that the test was initiated.
7.2.2 LED Indications with RLS Enabled
No. of
Flashes Functional Test Pass Fail
1 0 to 59min 1hr to 1hr 59min 121.5MHz homer
22hrs to 3hrs 59min 406MHz power
34hrs to 5hrs 59min AIS signal
46hrs to 7hrs 59min AIS Power
58hrs to 9hrs 59min Battery failure
610hrs + No GNSS
7.2.3 LED Indications for units configured with non-RLS Protocol
No. of
Flashes Functional Test Pass Fail
1 0 to 59min 1hr to 1hr 59min 121.5MHz homer
22hrs to 3hrs 59min 406MHz power
3 4hrs to 5hrs 59min AIS signal
4 6hrs to 7hrs 59min AIS Power
5 8hrs to 9hrs 59min Battery failure
6 10hrs + No GNSS

15/11/2022 912S-04064 - 01.02 19
GlobalFix V5 User Manual
!Because this test transmits a short burst on the aircraft distress frequency of
121.5MHz, please only carry out this test in the first 5 minutes of each hour.
!The battery must be replaced either prior to the expiry date shown on the rear
label or after the GlobalFix V5 has been activated.
!If, during a self test, the LED flashes magenta or amber the PLB3 may
not have sufficient energy to operate for the specified 24-hour period. Battery
replacement is recommended.
NOTE: The flash sequence will be repeated after a short pause and then the GlobalFix
V5 will automatically power off.
7.2.4 AIS Test
Two AIS transmissions will occur during a Functional Test indicating “EPIRB TEST” on AIS
receivers within range.
!To visualise an indication of a successful AIS transmission during test always
ensure the AIS receiving unit is configured to react to EPIRB Test signals.
7.3 GNSS Test
!This test should only be performed where the GlobalFix V5 has a clear and
unobstructed view of the sky. This is required to allow the GNSS receiver to
acquire a signal from sufficient satellites to allow it to determine a position.
Ensure the area marked “GNSS Antenna” is not obstructed.
It is recommended that a GNSS test is carried out at least once every six months to ensure
correct operation of the GlobalFix V5.
Press and hold the TEST key for 5 seconds. The LED will illuminate red to indicate
the key has been pressed, then start flashing. Shortly after, the LED will cease flashing and
become a steady red light. Release the TEST key now.
During the GNSS test the LED will repeat a long red flash followed by a short green
flash until either a position fix is obtained or the GNSS test fails.
A successful test will be indicated by a number of green LED flashes and an unsuc-
cessful test will be indicated by a number of red LED flashes. The number of flashes
indicates the number of GNSS tests remaining (e.g. 7 flashes = 7 tests remaining).
The test result flashes will be repeated after 2 seconds.
If there are 10 or more tests remaining then the LED will flash 10 times only (repeated).
The GlobalFix V5 has the capacity to carry out 60 GNSS tests within the lifetime of the
battery.
If there are no tests remaining immediately after the current test, the LED will flash green
or red rapidly for three seconds (not repeated) depending on whether the GNSS test
was successful or not, respectively.
When there are no tests remaining, the LED will flash red rapidly for three seconds (not
repeated).
The test can be ended at any time by holding the TEST key for 1 to 2 seconds.

GlobalFix V5 User Manual
20 912S-04064 - 01.02 15/11/2022
For further information regarding Self Test and Self Test history use the ACR Mobile App to
connect to your GlobalFix V5 using Near Field Communication (NFC).
Android iOS
BEACON REGISTRATION
!It is the owner’s responsibility to register this beacon with the appropriate
National Authority before operation.
Documentation is provided within the packaging with information regarding registration
with the relevant body to comply with the required configuration of the beacon.
NOTE: For all countries listed below it is preferred that registration is completed
on-line using the appropriate links.
7.4 Advice to owners of EPIRBs
Registration of 406 MHz satellite EPIRBs:
• Registration with the National Authority is mandatory because of the global alerting
nature of the system.
• The information provided in the registration card is used for rescue purposes only.
• See the owner registration card for the National Authority contact details on how
to register your beacon upon completion of the sales transaction. Before a beacon
enters service, it should be registered with the National Authority.
• If the beacon is being transferred to a new owner, the current owner needs to inform
the National Authority of the name and address of the new owner.
• All subsequent owners of the beacon are required to provide the National Authority
with the information as shown in the owner registration card.
7.5 Country Specific Registration Information
USA
NOAA-Sarsat, USMCC, NSOF, E/SPO53, 1315 East West Hwy, Silver Spring, MD, 20910
Fax: [phone], Tel: [phone] (1.888) 2127283
Email: beacon.r[email protected], Web: www.beaconregistration.noaa.gov/
CANADA
Beacon Registry, CMCC Trenton, 8 Wing Trenton, Box 1000 Stn Forces, Astra, Ontario, K0K 3W0
Fax: [phone], Tel: [phone]
Email: [email protected], Web: www.cbr-rcb.ca
UK
Distress & Security Beacon Registry, Pendennis Point, Castle Drive, Falmouth, TR11 4WZ
Fax: [phone], Tel: [phone]
Email: [email protected].uk, Web: www.gov.uk/406beacon
AUSTRALIA
Australian Maritime Safety Authority, GPO Box 2181, Canberra, Australia, ACT 2601
Fax: [phone] ([phone] (Int.)), Tel: [phone] ([phone] (Int.)
Email: [email protected].au, Web: www.amsa.gov.au/beacons
NEW ZEALAND
JRCC NZ, Avalon Studios, Percy Cameron Street, P.O. Box 30050, Lower Hutt, 5040
Fax: [phone], Tel: [phone] [phone]
Email: 406r[email protected], Web: www.beacons.org.nz
For other countries visit: www.406registration.com/countriessupported.aspx