ActivePure INDUCT GUARDIA N II User manual

INDUCTGUARDIANII
INDUCTGUARDIANIII
READ MANUAL CAREFULLY FOR PROPER USE AND OPTIMAL OPERATION.
&

2
GENERAL INFORMATION
If you have any questions concerning this, or any ActivePure product,
contact ActivePure Customer Service at 800.572.1446 or email
[e-mail].
CONTENTS
Product Overview . . . . . . . . . . 2
Specifications. . . . . . . . . . . . 2
Storage and Disposal . . . . . . . . . 2
Important Safety Instructions. . . . . . 3
For Canadian Customers Only . . . . . 4
Product Features . . . . . . . . . . 5
Installation Hardware (Supplied). . . . . 5
Recommended Installation Tools . . . . 6
Installation Requirements . . . . . . . 6
Electrical Requirements . . . . . . . . 7
Communication Connection . . . . . . 7
Installing the Unit . . . . . . . . . . 7
Wiring the Unit . . . . . . . . . . . 9
Maintenance/UV Bulb Indicator . . . . . 9
Changing the ActivePure®Cell . . . . . 10
Replacing the Ballast . . . . . . . . . 11
Replacement Parts & Service. . . . . . 13
Warranty Information . . . . . . . . . 13
FCC Declaration & Responsible Party . . 14
PRODUCT OVERVIEW
Congratulations on your purchase of the ActivePure®Induct Guardian II & III! The unit is easily mounted
into the supply side of air conditioning and heating system air ducts by an electrician or HVAC
professional, where it will provide 24/7 surface and air disinfection. Please read and follow all service
procedures outlined in this manual before installing or performing maintenance.
STORAGE AND DISPOSAL
Do not dispose of this product as household
waste. Electrical waste and electronic
products should be appropriately recycled as
required by practices established by your
local authority.
SPECIFICATIONS
ActivePure Induct Guardian II & III
• Model Number: A1024F (II) & A1025F (III)
• Sales Number: 00766 (II) & 00767 (III)
Technology:
ActivePure®
Electrical:
• Input Voltage: 120/277 VAC; ~ 50/60Hz
• Current: 0.27 Amp Max (II) & 0.54 Amp Max (III)
• Power: 20 Was (II) & 37 Was (III)
*Conforms to UL STD 1598.
Mechanical:
• Distribution via Air Handler
Safety Switch Installed
Weight & Dimensions:
• 4 lbs (1.8 kg.) (II) & 8 lbs (3.6 kg.) (III)
• 9” H x 9” W x 17” D (II)
(21.59 cm x 21.59 cm x 27.94 cm)
• 11” H x 11” W x 17” D (III)
(21.59 cm x 21.59 cm x 27.94 cm)
Operating Temperature:
• 34 ºF to 200 ºF (1 ºC – 93 ºC)
Recommended Maximum Coverage in a
Contiguous Space1:
• Every facility is unique and proper configuration
is an important as the technology. To validate
coverage in your facility, speak to your sales
representative or call customer service at
800-572-1446.
Warranty:
• Limited 5 Year Warranty
ActivePure Manufacturing, LLC reserves the right to
change or modify any specification without notice.

3
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
• UV Light in operation. Do not operate unless the unit is completely
and correctly assembled; failure to follow warnings may result in
severe eye damage and electrical shock
• To prevent damage to the unit, operating environment temperature
must never exceed 200 oF (93 oC)
• To reduce the risk of electric shock, this equipment may have a
grounding type plug that has a third (grounding) pin; this plug will
only fit into a grounding type power outlet; if the plug does not fit
into the outlet, contact qualified personnel to install the proper
outlet; DO NOT alter the plug in any way
• This unit is equipped with a universal ballast that operates at
nominal voltages between 100 and 277 VAC, 50/60 Hz
• To Reduce the Risk of Electric Shock – DO NOT use in wet or damp
locations; this equipment emits UV-C radiation; DO NOT locate
equipment in any location allowing direct line-of-sight to vents,
returns, or other duct openings
• DO NOT use this unit with an extension cord
WARNING
Location for Protective Earth Line.
CAUTION
• Wiring and installation of this unit must be done a licensed HVAC
contractor or electrician; failure to do so will void warranty of the
product
• When the unit is installed in a roof mounted HVAC system, the unit
must be protected from the elements
Read this manual in its entirety before using your ActivePure®Induct Guardian II & III.
Keep out of the reach of children.
• Live voltage may be present
• Disconnect power at the breaker or fuse panel before servicing unit; always follow OSHA lockout
procedures to prevent accidental exposure to electrical energy
• If installed near a furnace or where emergency heat coils could raise the temperature inside the
plenum, cycle the AC unit through three full heating cycles assuring that the temperature never
exceeds 200 °F (93 °C); the ActivePure®Cell must not exceed 200 °F (93 °C)
• If the unit is hard wired, be sure the power to the unit is o; always follow OHSA electrical lockout
safety requirements to prevent accidental release of energy during service or maintenance activities
• Never aempt to check operation of the ActivePure®Cell(s) by direct observation; severe eye
damage can result; use the indicator lamps on the boom of the ballast only

4
FOR CANADIAN CUSTOMERS ONLY
ACTIVEPURE®INDUCT GUARDIAN II  III
Sales No. : 00766 (Induct Guardian II)
Sales No. : 00767 (Induct Guardian III)
This UV device helps reduce the spread of viruses in the air.
Keep out of the reach of children.
Please read the label and owner's manual before using: www.activepure.com/manuals
PRECAUTIONS:
WARNING: UV radiation emied from this device. Unintended use of the device, or damage to the
housing, may result in exposure to ultraviolet radiation. Ultraviolet radiation may cause eye and skin
irritation. Avoid exposing eyes and skin to ultraviolet radiation.
FIRST AID INSTRUCTIONS: Please contact your healthcare provider in the event of injury caused by this
device.
DIRECTIONS FOR USE:
Unit should be installed aer the air handler in the HVAC system by a licensed HVAC contractor or
electrician. Please see owner's manual for detailed instructions on using, handling, storing and disposing
of the device, and procedures to mitigate any associated risks.
The use of this device is a supplement to and not a substitute for standard infection control practices;
users must continue to follow all current infection control practices, including those related to the
cleaning and disinfection of environmental surfaces.
FOR INQUIRIES CONTACT:
AERUS CANADA, INC.
Laird Business Park
3480 Laird Road, Units 2–5
Mississauga, Ontario, Canada, L5L 5Y4
W. Parrell, Manager
[phone]
[email protected]
Aerus Canada, Inc. is ailiated with ActivePure Manufacturing, LLC
1300 Valley Drive, Bristol, VA 24201

5
PRODUCT FEATURES
Ballast Plate
Relay Port
Ballast Plate
Relay Port
ActivePure®Cell
Removable Ballast Cover
Removable Ballast
Cover
ActivePure®Cell
INSTALLATION HARDWARE SUPPLIED
(8) #8 - .75 1/4” Self-tapping screws
Item # US7067
(4) #6 - 32 X 2 inch Threaded bolts
Item #US70680
(2) Thumb screws
Item #36-00213
(2) Thumb nuts
Item #36-00214
(4) #6 - 32 Toggle
bolt wall anchors
Item # US70682
It is important to be familiar with the parts of the ActivePure®Induct Guardian II & III. If any parts are
missing, contact your sales representative or ActivePure Customer Service.

6
RECOMMENDED INSTALLATION TOOLS
INSTALLATION REQUIREMENTS
1. Unit should be installed aer the air handler in the
HVAC system.
2. The duct work around the installation area should
be clean and dry to ensure proper adhesion of the
gasket materials and any tape used.
3. When installing near a furnace or heating coils, run
the heating system through three (3) full heating
cycles to ensure the temperature of the INDUCT
unit does not exceed 200 °F (93 °C).
• This unit must be installed by a licensed HVAC contractor or
electrician; failure to do so will void warranty of the product
• When the unit is installed in a roof mounted HVAC system, the unit
must be protected from the elements
CAUTION
If installed near a furnace or where emergency heat coils could raise
the temperature inside the plenum, cycle the AC unit through three
full heating cycles assuring that the temperature never exceeds 200 °F
(93 °C). The ActivePure®Cell must not exceed 200 °F (93 °C).
WARNING
3 1/2” Hole Saw
(for wood or metal)
Drill/Power
Driver
Phillips
Screwdriver
3/8” Drill Bit
(if installing into
fiberglass ducting with
toggle bolts)
YOU MAY ALSO NEED:
1/4” Nut
Driver
Bit
When the unit is installed in a roof mounted HVAC system, the unit
must be protected from elements.
CAUTION
Tin Snips
(for metal ductwork)
Utility Knife Dust Mask
1/4
Air Handler
ActivePure®Induct Guardian II
Min. 10” x 10”
ActivePure®Induct Guardian III
Min. 12” x 12”
Installation Clearance
4. Depending on model, one opening (ActivePure®Induct Guardian II) or two openings
(ActivePure®Induct Guardian III) approximately 4” (four inches) (10.16 cm) in diameter will need to
be cut into the existing duct work to install the unit properly.
NOTE: Unit requires power 24/7. Do not install where power to the unit will be cycled on and o.

7
COMMUNICATION CONNECTION
This Induct Guardian II / III provides a dry-contact relay port for optional
remote monitoring of cell operation. Contacts are closed during normal
operation and open if there is an interruption in operation.
Maximum contact rating = 250V AC / 8A. (see port location on Page 3)
NOTE: Port is an industry-standard pluggable terminal block type with
2-position, 0.2” (5.08mm) pitch.
ELECTRICAL REQUIREMENTS
For 120V Domestic Units: Black = L1, White = Neutral, Green = Ground
For 220V Commercial Units: Black = L1, White = L2, Green = Ground
For 230V International Units: Brown = L1, Blue = L2, Green w/yellow stripe = Ground
• Wiring of the unit into your HVAC system should be done by a
licensed HVAC installer or electrical contractor only
• This unit is equipped with a universal ballast that operates at
nominal voltages between 100 and 277 VAC, 50/60 Hz
CAUTION
To Reduce the Risk of Electric Shock – DO NOT use in wet or damp
locations. This equipment emits UV-C radiation. DO NOT locate
equipment in any location allowing direct line-of-sight to vents,
returns, or other duct openings. Disconnect from supply before
servicing or replacing.
WARNING
Relay Port
INSTALLING THE UNIT
To Reduce the Risk of Electric Shock – DO NOT use in wet or damp
locations. This equipment emits UV-C radiation. DO NOT locate
equipment in any location allowing direct line-of-sight to vents,
returns, or other duct openings. Disconnect from supply before
servicing or replacing.
WARNING
• Hard wiring unit into HVAC system must be done by a licensed HVAC
installer or electrical contractor only
• When the unit is installed in a roof mounted HVAC system, the unit
must be protected from elements
• Unit requires power 24/7; DO NOT install where power to the unit will
be cycled on and o
CAUTION

8
7. Unit may be taped
with aluminum HVAC
tape to provide
complete seal.
6. Move ballast assembly
to location and secure to
duct work with the four (4)
thumb screws provided.
5. Place the mounting plate
squarely into place and
fasten to duct work with
sheet metal screws.
3. Using the mounting plate
as a template, mark the
location for installation.
4. Using a 4" (4 inch) hole saw, cut
opening(s) into duct work.
Cut the second hole for
Induct Guardian III only.
1. Locate suitable area of
duct for installation.
2. Cut away insulation to expose
metal duct (if needed).
NOTE: Unit requires power 24/7. Do not install where power to the unit will be cycled on and o.
Find the optimal position downstream from the air handler. Ensure location in duct has enough room for
the mounting plate. It is recommended for maximum eectiveness that the unit be placed as close to the
air handler as possible.
NOTE: The illustrations are shown installing an ActivePure®Induct Guardian III. The procedures shown in
this manual apply to both units, unless otherwise indicated.
INSTALLING THE UNIT CONT.

9
WIRING THE UNIT
2. Connect the unit to the load side of the proper fan relay.
4. Check indicator light for proper operation with fan on.
1. Connect wires coming from the ActivePure®Induct Guardian II / III unit as follows:
NOTE: All units come standard with a blunt cord.
120 Volt Unit:
Black Wire L1
White Wire Neutral
Green Wire Ground
220 Volt Unit:
Black Wire L1
White Wire L2
Green Wire Ground
International Unit:
Brown Wire L1
Blue Wire L2
Green with
Yellow Stripe Ground
Disconnect power at the breaker or fuse panel before servicing unit.
Always follow OSHA lockout procedures to prevent accidental exposure
to electrical energy.
WARNING
3. Be sure to ground the ballast by securing the unit to the metal surface
of the AC unit or power box.
Hard wiring unit into HVAC system should be done by a licensed HVAC
installer or qualified electrical contractor only.
CAUTION
Your ActivePure®Induct Guardian II / III unit requires no periodic
maintenance beyond normal replacement of the ActivePure®Cell every
one (1) year.
The UV Bulb Indicator on the face of the unit will glow when the
UV bulb is in use. If the indicator does not glow and the unit has power,
the ActivePure®Cell should be replaced.
Note: For optimal performance and to maintain the Limited 5 year
warranty, it is required to replace the ActivePure® Cell every year,
even if the UV bulb appears to be operating normally.
UV Bulb Indicator
HVACENVIRONMENTAL CONDITIONING SYSTEM
SYSTÈME DE CONDITIONNEMENTD ’AIRCVC
UV Lamp in operation when lit. | Lampe UVen march e lorsque levoyant est allumé .
MAINTENANCE/UV BULB INDICATOR

10
CHANGING THE ACTIVEPURE®CELL
4. Remove the used ActivePure Cell
from the base unit and dispose of
the bulb properly.
3. Remove the thumb screws on
either side of the ActivePure®
Cell to remove the cell from the
ballast assembly.
WARNING
• UV Light in operation; disconnect unit from power cord before
servicing; failure to follow warnings may result in severe eye damage
• If the unit is hard wired, be sure the power to the unit is o;
always follow OHSA electrical lockout safety requirements
to prevent accidental release of energy during service or
maintenance activities
2. Remove the ActivePure®Induct
ballast assembly by removing the
four (4) thumb screws and sliding
the unit out.
1. Disconnect (unplug) power cord
from unit.
5. Plug the new ActivePure Cell into the base
unit. Be sure Air Flow / Honeycomb Cell
direction is correct.
6. Secure with (2) thumb screws.

11
CHANGING THE ACTIVEPURE®CELL CONT.
7. Insert the unit into the
mounting plate.
8. Secure unit with (4)
thumb nuts.
9. Reconnect power supply.
Power Cord
NOTE: Always follow OHSA electrical lockout safety requirements to prevent accidental release of energy
during service or maintenance activities.
Visit www.lamprecycle.org for proper bulb disposal regulations
REPLACING THE BALLAST
• Never aempt to check operation of the ActivePure®Cell(s) by direct
observation; severe eye damage can result; use the indicator lamps
on the boom of the ballast only
• Disconnect power at the breaker or fuse panel before servicing
unit; always follow OSHA lockout procedures to prevent accidental
exposure to electrical energy; release of energy during service or
maintenance activities
WARNING
2. Open the ballast housing by removing the four (4) thumb
screws then remove the cover.
HVACENVIRO NMENTAL CONDITIONING SYSTEM
SYSTÈME DE CONDITIONNEMENT D’AIRCVC
UV Lamp in operation when lit. | Lampe UVen m arche lorsque le voyante st allumé.
1. Disconnect (unplug) power cord from unit.

12
3. Remove the two (2) thumb nuts on the top and
bottom side of the ballast to pull ballast from
assembly.
4. Remove the wires from ballast by pressing a small
screwdriver into the wire release:
• Induct Guardian II - 6 wires
• Induct Guardian III - 8 wires
UPPER (3 terminals)
• Black power wire in BLACK
• White power wire in WHITE
• GREEN is not used
7. Replace cover and secure with the original four (4) screws.
6. Place new ballast into original location and secure using the
two (2) nuts removed in step 4.
5. To reconnect wiring, insert wire into the corresponding color
connector. Gently pull back after inserting wire to ensure the
wire is properly locked into place.
LOWER (6 terminals)
• 2 Red wires in RED
• 2 Blue wires in BLUE
(Induct Guardian III ONLY)
• 2 Yellow wires in YELLOW
GREEN WHITE BLACK
RED RED
YELLOW YELLOW
BLUE BLUE
RED RED
YELLOW
YELLOW
BLUE BLUE
GREEN WHITE BLACK
REPLACING THE BALLAST CONT.

13
8. Re-install unit if removed from duct. Reconnect power and
check for proper operation.
NOTE: UV Bulb Indicator should be lit when in operation UV Bulb Indicator
REPLACING THE BALLAST CONT.
Limited 5 Year Warranty
To register your ActivePure®Induct Guardian II & III unit, visit www.activepure.com/warranty.
To view full details of warranty coverage, visit www.activepure.com/manuals.
WARRANTY INFORMATION
If you have any questions concerning this, or any ActivePure product,
contact ActivePure Customer Service at 800.572.1446 or email
[e-mail].
REPLACEMENT PARTS QTY PART NUMBER
Ozone free ActivePure®Cell US71089
Ballast 9950255
REPLACEMENT PARTS  SERVICE
To order replacement parts, contact your sales representative or ActivePure
Customer Service for further assistance at 800.572.1446 or email
[e-mail].
62-01503 VA-01664C
HVACENVIRONMENTALCONDITIONING SYSTEM
SYSTÈME DE CONDITIONNEMEN TD’AIR CVC
UVLamp in operation when lit. | LampeUVenmarche lorsquelevoyantestallumé.
Induct Guardian II Induct Guardian III
HVACENVIRONMENTAL CONDITIONING SYSTEM
SYSTÈMEDE C ONDITIONNEMENTD’AIR CVC
UVLa mp in operation when lit. | Lamp eU Ven marche lors que levoyant est allumé.
Ballast
Ballast
ActivePure®
Cell ActivePure®
Cells (2)
NOTE: Two ActivePure Cells are needed for the ActivePure Induct Guardian III.

14
FCC Declaration of Conformity
Name: ActivePure®Induct Guardian II / III
Model: A1024F (Induct Guardian II)
A1025F (Induct Guardian III)
Produced by: ActivePure Manufacturing, LLC
This device complies with Part 15 of the
FCC Rules.
Responsible Party
ActivePure Manufacturing, LLC
1300 Valley Drive
Bristol, VA 24201
Ph: 800.572.1446
Signature:
Printed Name: Andrew Eide
Title: Vice President of Product Development
and Manufacturing
Date: 01/11/22
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant of
part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy, and if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
• Consult the Independent Contractor for
help.
FCC DECLARATION  RESPONSIBLE PARTY

15

16
For information regarding the use of this product, please call Customer Service.
1.800.572.1446 or email at [e-mail]
www.activepure.com
ActivePure Manufacturing, LLC | 1300 Valley Drive | Bristol, VA 24201 | 800.572.1446
Assembled in U.S.A. | © ActivePure Manufacturing, LLC. All Rights Reserved AIG2-3_OM_65-00842_VA-01665B

17
INDUCTGUARDIANII
INDUCTGUARDIANIII
LIRE ATTENTIVEMENT LE MANUEL AFIN D’UTILISER CORRECTEMENT
L’APPAREIL ET D’ASSURER SON FONCTIONNEMENT OPTIMAL.
&
ET

18
INFORMATIONS GÉNÉRALES
Si vous avez des questions concernant cet appareil ou un autre produit
ActivePure®, contactez le service à la clientèle ActivePure®au 1.800.572.1446
ou par courriel à l’adresse [e-mail]..
DESCRIPTION DU PRODUIT
Félicitations pour votre achat de l’ActivePure®Induct Guardian II & III! L’appareil se monte facilement sur
le côté alimentation des conduits d’air d’un système de climatisation et de chauage, par un électricien
ou un professionnel du CVC, afin d’assurer une désinfection des surfaces et de l’air 24 h/24 et 7 j/7.
Veuillez lire et suivre toutes les procédures de service décrites dans le présent manuel avant de l’installer
ou d’eectuer des réparations.
STOCKAGE ET MISE AU REBUT
Ne pas jeter ce produit comme déchet
ménager. Les déchets électriques et les
produits électroniques doivent être recyclés
convenablement, conformément aux
pratiques établies par votre administration
locale.
TABLE DES MATIÈRES
Description du produit . . . . . . . . 18
Spécifications. . . . . . . . . . . . 18
Stockage et mise au rebut . . . . . . . 18
Consignes de sécurité importantes . . . 19
Pour les clients au Canada seulement . .20
Caractéristiques du produit . . . . . . 21
Matériel d’installation (fourni) . . . . . . 21
Outils d’installation recommandés . . . .22
Exigences d’installation . . . . . . . .22
Installation électrique . . . . . . . . .23
Connexion de communication . . . . .23
Installation de l’appareil . . . . . . . .24
Branchement de l’appareil . . . . . . .25
Entretien/Indicateur de lampe UV . . . .25
Remplacement de la cellule ActivePure®. .26
Changement du ballast . . . . . . . .27
Pièces de rechange et service . . . . .29
Informations relatives à la garantie . . . .29
Déclaration FCC et partie responsable . 30
SPÉCIFICATIONS
ActivePure Induct Guardian II & III
• Modèle numéro: A1024F (II) & A1025F (III)
• Numéro de série: 00766 (II) & 00767 (III)
Technologie:
ActivePure®
Électrique:
• Tension d’alimentation : 120/277 VCA;
~ 50/60 Hz
•Courant : 0,27 A maximum (II) &
0,54 A maximum (III)
•Puissance : 20 W (II) & 37W (III)
*Conforme à la norme UL STD 1598.
Mécanique:
• Distribution par une unité de traitement de l’air
avec interrupteur de sécurité
Poids et dimensions:
• 4 lb (1,8 kg) (II) et 8 lb (3,6 kg) (III)
• 9 po H x 9 po L x 17 po P (II)
(21,59 cm x 21,59 cm x 27,94 cm)
• 11 po H x 11 po L x 17 po P (III)
(21,59 cm x 21,59 cm x 27,94 cm)
Température de fonctionnement:
• 34 °F à 200 °F (1 °C – 93 °C)
Couverture maximale recommandée
pour un espace étroit1:
• Chaque lieu est unique et une bonne
configuration est aussi importante que la
technologie. Pour approuver la couverture
dans votre bâtiment, consultez votre
représentant commercial ou contactez le
service à la clientèle au 1.800.572.1446.
Garantie:
• Garantie limitée de 5 ans
ActivePure Manufacturing, LLC reserves the right to
change or modify any specification without notice.

19
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES CONSIGNES
• Lampe UV en marche. Ne pas faire fonctionner l’appareil avant qu’il
ne soit complètement et correctement monté; le non-respect de
cet avertissement peut entraîner de graves lésions oculaires et une
décharge électrique
• Pour éviter d’endommager l’appareil, la température de
l’environnement de marche ne doit pas dépasser les 200 °F (93 °C)
• Afin de réduire les risques de décharge électrique, cee unité
peut posséder une fiche de courant avec mise à la terre avec une
troisième broche (de mise à la terre); cee fiche ne s’insère que
dans une prise de courant avec mise à la terre; si la fiche ne s’insère
pas dans la prise, demandez à un professionnel qualifié d’installer
une prise adéquate; NE PAS modifier la fiche de quelque manière
que ce soit
• Cet appareil est équipé d’un ballast universel fonctionnant avec une
tension nominale comprise entre 100 et 277 VCA, 50/60 Hz
• Afin de réduire les risques de décharge électrique, NE PAS
utiliser dans des lieux mouillés ou humides; cet appareil émet un
rayonnement UVC; NE PAS placer l’unité dans des lieux permeant
une exposition directe aux ventilations, retours ou autres bouches
d’aération
• NE PAS utiliser cet appareil avec une rallonge
MISE EN
GARDE
Emplacement de la mise à la terre.
ATTENTION
• Le branchement et l’installation de cet appareil doivent être
eectués par un fournisseur ou un électricien agréé en CVC, sinon la
garantie du produit sera annulée
• Si l’appareil est installé dans un système CVC fixé sur un toit, il doit
être protégé des éléments
Veuillez lire entièrement ce manuel avant d’utiliser votre ActivePure® Induct Guardian II & III.
Garder hors de la portée des enfants.
• Possibilité de haute tension
• Débranchez l’alimentation dans le tableau des disjoncteurs ou des fusibles avant de faire l’entretien;
suivez toujours les procédures de verrouillage OSHA afin de prévenir une exposition accidentelle à
l’énergie électrique
• En cas d’installation près d’un appareil de chauage central ou à un endroit où des serpentins
chauants pourraient augmenter la température de la chambre de distribution, faites fonctionner
l’unité d’air conditionné pendant trois cycles de chauage complets en vous assurant que la
température ne dépasse jamais 200 °F (93 °C); la cellule ActivePure®ne doit pas dépasser 200 °F (93 °C)
• Si l’appareil est branché par un câble, assurez-vous que l’alimentation de l’appareil est coupée;
suivez toujours les procédures de verrouillage OHSA afin de prévenir une fuite accidentelle
d’énergie durant l’entretien
• N’essayez jamais de vérifier le fonctionnement des cellules ActivePure®par observation directe, cela
peut provoquer des dommages oculaires graves; utilisez uniquement les indicateurs de lampe UV
en bas du ballast

20
POUR LES CLIENTS AU CANADA SEULEMENT
ACTIVEPURE®INDUCT GUARDIAN II  III
Numéro de série: 00766 (Induct Guardian II)
Numéro de série: 00767 (Induct Guardian III)
Ce modèle à rayons UV permet de réduire la propagation des virus dans l’air.
Garder hors de la portée des enfants.
Veuillez lire l’étiquee et le guide du propriétaire avant l’utilisation: www.activepure.com/manuals
PRÉCAUTIONS:
MISE EN GARDE: Cet appareil émet des rayonnements UV. L’utilisation involontaire de cet appareil ou un
boîtier endommagé peut entraîner l’exposition à des rayons ultraviolets. Les rayonnements ultraviolets
peuvent irriter les yeux et la peau. Évitez d’exposer vos yeux et votre peau aux rayons ultraviolets.
INSTRUCTIONS POUR LES PREMIERS SOINS: Veuillez contacter votre professionnel de la santé en cas
de blessure causée par cet appareil.
MODE D’EMPLOI:
L’appareil doit être installé sur l’unité de traitement de l’air dans le système CVC par un fournisseur ou
électricien agréé en CVC. Veuillez consulter le manuel du propriétaire pour des instructions détaillées sur
l’utilisation, la manipulation, le stockage et la mise au rebut de l’appareil, ainsi que les procédures pour
réduire tout risque connexe.
L’utilisation de cet appareil agit en complément des pratiques standards de contrôle des infections
et ne représente donc pas un moyen de substitution à celles-ci. Les utilisateurs doivent continuer à
suivre toutes les pratiques standards actuelles en matière de contrôle des infections, y compris celles
concernant le neoyage et la désinfection des surfaces environnantes.
POUR TOUTE QUESTION, VEUILLEZ CONTACTER:
AERUS CANADA, INC.
Laird Business Park
3480 Laird Road, Unités 2 – 5
Mississauga (Ontario) L5L 5Y4 Canada
W. Parrell, Responsable
[phone]
wparrell@aerusonline .com
Aerus Canada, inc. est ailiée à ActivePure Manufacturing, LLC,
1300 Valley Drive, Bristol, VA 24201