ActivePure Surface & Air Guardian User manual

x2
ActivePure Manufacturing, LLC
1300 Valley Drive
Bristol, VA 242010
READ MANUAL CAREFULLY FOR PROPER USE AND OPTIMAL OPERATION.
SURFACE & A I R GUARD I A N

2
SPECIFICATIONS
Technology:
• ActivePure®Cells (2 included)
• Positive and Negative Multipoint and RF Ion Generation
• HEPA & Activated Carbon Filter
Electrical:
• Input Voltage: 100 ~ 240 VAC; 50/60 Hz
• external power supply
• DC 24 Volts; 1.5 Amps Max
• Power Consumption: 43 Watts Max.
Mechanical:
• Nominal Airow Rate: 40-60 CFM Fan
Dimensions:
• 11.75” H x 9.5” W x 10” D
• (29.8 cm x 24.1 cm x 25.4 cm)
Weight:
• 7.6 lbs
• 3.45 kg
Opertating temp:
• 34°F – 100°F
• 1.6°C - 38°C
Coverage:
• Up to 2,000 sq. ft. (186 m2)*
*Depends on room occupancy and layout
Warranty:
• Limited 3 year warranty
ActivePure® reserves the right to change or modify any specication
without notice.
PRODUCT OVERVIEW
Congratulations on your purchase! Your new ActivePure® Surface & Air Guardian is designed to provide years of trouble-free, low
maintenance operation. Be sure to read and follow all service procedures outlined in this owner’s manual, and use only genuine
ActivePure® replacement parts.
If you have any questions concerning this, or any ActivePure®product, contact ActivePure®
Customer Service at 800.572.1446 or email [e-mail].
GENERAL INFORMATION
CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . 2
Specications . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . 3
Your New ActivePure® Surface & Air Guardian . . . . . . 4
Inspection & Installation . . . . . . . . . . . . . . . 4
Unit Features . . . . . . . . . . . . . . . . . . . 4
Placement of Unit . . . . . . . . . . . . . . . . . 5
Operation . . . . . . . . . . . . . . . . . . . . . 5
Settings & Adjustments . . . . . . . . . . . . . . . 6
LED Display . . . . . . . . . . . . . . . . . . . . 6
Maintenance Reminders . . . . . . . . . . . . . . . 7
General Maintenance . . . . . . . . . . . . . . . . 8
Removing the Filter Assembly . . . . . . . . . . . . 9
Optional HEPA Filter Sheet . . . . . . . . . . . . . . 9
Removing the ActivePure® Cell . . . . . . . . . . . . 10
Installing the ActivePure® Cell . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . 11
Replacement Parts . . . . . . . . . . . . . . . . . 12
Warranty Information . . . . . . . . . . . . . . . . 13

3
IMPORTANT SAFETY INSTRUCTIONS
Read this manual in its entirety before using your ActivePure®Surface & Air Guardian
• NEVER place your unit where it may fall into a bathtub or other water container; to protect against electrical hazards, DO
NOT immerse in water or other liquids
• DO NOT touch the control panel or plug with a wet hands
• DO NOT run cord under carpeting; DO NOT cover cord with throw rugs, runners, or similar coverings; arrange cord away
from traffic area and where it will not be tripped over
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or
fire, or damage the air cleaner
• To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner; DO NOT use on soft surfaces, like a bed,
where openings may become blocked
• To avoid fire or shock hazard, plug the unit directly into an electrical outlet
• To disconnect the unit, turn controls to OFF, then remove plug from outlet; pull firmly on the plug, DO NOT unplug by
pulling on the cord
• Always unplug the unit before moving or cleaning, or whenever the unit is not in use
• DO NOT use outdoors or on wet surfaces
• DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit, doing so will void your warranty
• Connect to properly grounded outlets only
• To reduce the risk of electrical shock, do not change the plug in any way; do not use adaptors
• When using electrical appliances, basic precautions should always be followed to reduce risk of re, electric
shock, and injury to persons, including the following:
• Eye damage may result from directly viewing the light produced by the lamp used in this product; always turn
o & unplug unit before removing lters or bulbs
• Do not operate this unit without the Filter Assembly and Back Cover installed
• Disconnect power cord before servicing
WARNING:
• Allow your ActivePure®Surface & Air Guardian to warm to room temperature before operating; damage may
result from turning on a cold unit
• Do not operate unit near heat sources, open ame, or combustible vapors or gases
CAUTION:
SAVE THESE INSTRUCTIONS

4
1. Remove protective packaging
2. Remove unit from shipping carton
3. Remove all protective materials
4. Check for shipping damage and loose or broken parts
5. Read Owner’s Manual thoroughly prior to installation
6. Determine placement location for the unit (See “Placement of Unit” on page 5)
7. Insert the Power Supply Plug into the power receptacle on the rear of the unit. Plug the appropriate cord into the Power Supply
and into a working electrical outlet
8. Using the Power button, turn the unit ON
INSPECTION & INSTALLATION
• Exclusive ActivePure®Technology
• Positive and Negative Multipoint and RF Ion Generation
• Five Speed Fan
• LED Display
• Maintenance Reminders
• Replaceable ActivePure®Cells
• Removable Rear Grill
• Universal Power Supply with Cords
x2
LED Display Controls
x2
UNIT FEATURES
Power
Receptacle
Back of Unit /
Rear Access Power
Supply Plug
Cords
Power
Supply

5
1. Insert the Power Supply Plug into the power receptacle on
the rear of the unit. Plug the appropriate cord into the Power
Supply and into a working electrical outlet.
2. Push the Power button once to turn the unit on.
3. Push the A-PURE/A-PURE x2 button twice to set it to A-PURE
x2 level which will be illuminated on the screen.
4. Push the Fan + button four times to reach the highest speed
(5th level).
Place your unit in its permanent location:
• Unit should be four feet or higher from the ground
• Never set unit on the floor
• Place unit in a location away from the HVAC return duct, if applicable
NOTE: The rear of the unit should always have at least one inch of open area to allow unrestricted airflow.
PLACEMENT OF UNIT
OPERATION
• A·PURE MODE: The unit’s display shows the
fan speed (low to high) and A·PURE to indicate
that the ActivePure®Cell and ionization are
both functioning normally.
• A·PURE x2 MODE: A·PURE x2 lights up,
indicates that (2) ActivePure®Cells and
ionization are both functioning normally.
• ION MODE: Ion lights up, indicates only
ionization is functioning.
• CLEAN: Clean illuminates when cleaning is
required.
• RESE T: Clears the maintenance reminders
after performing routine maintenance.
• CELL: The Cell light will flicker when it is time
to replace your ActivePure®Cell.
To prevent injury, be sure the power cord is not accessible to small children.
CAUTION: