Adaptec M3093GX Operating and maintenance manual

M3093GX\DG\M3096G\GX\M3097G+\DG
Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI
Win2000\XP Installation Procedure
Rev050304A
Step A: Required hardware.
To install these models you will need a Narrow SCSI 50-pin controller and six foot (maximum)
Narrow SCSI cable.
Step B: Removing the shipping bracket.
It is recommended that before you connect the scanner to your computer that you inspect the
scanner and remove the shipping bracket first.
Removing the shipping bracket: The flatbed scanner models typically come with a
factory installed shipping lock designed to protect the scanner during shipment. Before
the scanner can be used the shipping lock must be unlocked. Follow these instructions
to unlock the shipping bracket:
1. Slide the scanner to its side as shown in figure below.
2. Unscrew the retainer screw and remove the shipping bracket.
3. Place the shipping bracket in the “use position” slot and secure it with the retainer
screw (see figure below)
4. Place scanner back in its normal position

M3093GX\DG\M3096G\GX\M3097G+\DG
Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI
Win2000\XP Installation Procedure
Rev050304A
Special note: The Fi-4340C shipping lock is a knob located underneath the exit tray. To unlock
it twist a quarter turn counter-clockwise so that it is vertical. The Fi-4530C does not have a
shipping lock.
Step C: Installing the SCSI Host Adapter.
1. Shut down your PC and remove the case cover.
2. Locate a free PCI slot and remove the back plate if necessary.
3. Install the SCSI controller in an open PCI slot.
Make sure that the card is seated completely in the slot and secured in the frame
Warning! Failure to secure the SCSI controller in the PC can result in damage to the
SCSI card, scanner, and/or your system.
4. Boot your PC without the scanner attached.
Step D: Installing the SCSI drivers (Adaptec).
1. When the New Hardware wizard comes up, allow Windows to finish installing the
files for the SCSI controller.
2. Then go to www.adaptec.com, and click on the “search” tab. Scroll down to the
“Enter key word or quoted phrase” box and type in “aspi”.
3. Next scroll down to the drivers section, click on ASPI_v470 or higher and follow the
prompts to download it.
4. Afterwards go to that folder and unzip the file to the default Adaptec\ASPI folder. For
Win2000 go to start, run, browse to the Adaptec\ASPI folder, select ASPIINST.EXE
and run it. For WinXP go to start, run, browse to the Adaptec\ASPI folder, select
INSTALL.BAT file in the directory the files extracted to and select the OPEN button.
In the command box, add a space and either XP32 for Pentium I/II/III/IV processors
or XP64 for Itanium processors. The command should look like:
c:\adaptec\aspi\install.bat XP32 or c:\adaptec\aspi\install.bat XP64. Then select
the OK button to run it.
5. Reboot and check for errors. If no errors shut down your system and go to the next
step.
Step E: Connecting the Scanner.
Warning! Ensure power is off when connecting or disconnecting any cables to the scanner or
workstation.
Setting the SCSI ID: The factory setting for the Scanner is 6, however, selecting a
different SCSI ID may be required when there are several devices on a SCSI chain.
Using a suitable tool, turn the selector switch until the arrow points to the desired ID
number (see figure 2-3). Setting the SCSI ID to 0, 1, or 7 is NOT recommended as these
settings are typically reserved for hard drives and the SCSI host adapter.
Setting Termination: The Fujitsu M3093GX\M3096G\GX\M3097G+\DG scanners come
with a plug in SCSI terminator (see figure below). The Fi-4340C\Fi-4640S\M4097D\Fi-
4750C\L scanners come with built in termination that is turned on or off through the
scanner panel. Termination for the Fi-4530C is handled automatically by the scanner. If
the scanner is the last device on the SCSI chain then the terminator should be placed on

M3093GX\DG\M3096G\GX\M3097G+\DG
Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI
Win2000\XP Installation Procedure
Rev050304A
one of the SCSI ports or turned on. If the scanner is not the last device on the SCSI
chain, then the terminator should be removed or turned off before connecting to the next
SCSI device.
Connecting SCSI cable: Located on the back of the scanner are the SCSI ports.
Depending on the model the ports may be either a High Density 50-pin (HD-50) or a 50-
pin Centronics. Use the appropriate cable to connect the scanner to the SCSI controller
in your PC. Ensure all connections are securely fastened.
Powering On: Connect the power cord to the scanner and a wall outlet then turn on the
scanner. For those models without a power switch plug in the power supply to the back
of the scanner. For proper communication between the Scanner and the Workstation,
switch on the scanner prior to switching on the workstation. The scanner power and
LCD display will light up. Next after the scanner completes its startup initialization the
LCD will display either ready or the number one. This indicates that the scanner is
ready.
Step F: Installing the ISIS driver.
1. Create a new folder and name it ISIS Download.
2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.
3. In the sub frame under the Product Support column click on Scanners.
4. On the next page select Drivers and Downloads.
5. Afterwards click on ISIS Software Drivers.
6. Locate the appropriate ISIS driver for your scanner by cross-referencing the scanner
model column on the left to the software column.
7. Double click on the driver file name and the File Download box will popup.
8. Click on Save and then use the browse (or other folder navigation) button until you
have the ISIS Download folder you created in the Save In Box.
9. Click Save.
10. When completed close the Download Complete window and go to the ISIS
Download folder.
11. Open the folder and you will see the saved ISIS driver file. Double click on the file to
unzip it and the WinZip* self-extractor box will popup. Click on browse and select the

M3093GX\DG\M3096G\GX\M3097G+\DG
Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI
Win2000\XP Installation Procedure
Rev050304A
ISIS Download folder, then click on Extract. The file will begin to unzip and when
finished a message box will report the number of files unzipped. Click on OK and
close WinZip.
12. In the ISIS Download folder locate the setup.exe file and double click. Afterwards
follow the prompts and reboot when finished.
Step G: Installing the STI-Twain driver for the Fi-4340C\Fi-4530C\Fi-4640S\M4097D\
Fi-4750C\L\Fi-5750.
Special note: Use the ASPI-Twain driver for the M3093GX\DG\M3096G\GX\M3097G+\DG.
1. Create a new folder and name it Twain Download.
2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.
3. In the sub frame under the Product Support column click on Scanners.
4. On the next page select Drivers and Downloads.
5. Afterwards click on STI Twain Software Drivers.
6. Locate the appropriate STI Twain driver for your scanner by cross-referencing the
scanner model column on the left to the software column.
7. Double click on the driver file name and the File Download box will popup.
8. Click on Save and then use the browse (or other folder navigation) button until you
have the Twain Download folder you created in the Save In Box.
9. Click Save.
10. When completed close the Download Complete window and go to the Twain
Download folder.
11. Open the folder and you will see the saved STI Twain driver file. Double click on the
file to unzip it and the WinZip* self-extractor box will popup. Click on browse and
select the STI Twain Download folder, then click on Extract. The file will begin to
unzip and when finished a message box will report the number of files unzipped.
Click on OK and close WinZip.
12. In the STI Twain Download folder locate the setup.exe file and double click.
Afterwards follow the prompts and reboot when finished.
Step H: Installing the Twain driver for the M3093GX\DG\M3096G\GX\M3097G+\DG.
1. Create a new folder and name it Twain Download.
2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.
3. In the sub frame under the Product Support column click on Scanners.
4. On the next page select Drivers and Downloads.
5. Afterwards click on ASPI Twain Software Drivers.
6. Locate the appropriate ASPI Twain driver for your scanner by cross-referencing the
scanner model column on the left to the software column.
7. Double click on the driver file name and the File Download box will popup.
8. Click on Save and then use the browse (or other folder navigation) button until you
have the Twain Download folder you created in the Save In Box.
9. Click Save.
10. When completed close the Download Complete window and go to the Twain
Download folder.
11. Open the folder and you will see the saved ASPI Twain driver file. Double click on
the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and
select the ASPI Twain Download folder, then click on Extract. The file will begin to
unzip and when finished a message box will report the number of files unzipped.
Click on OK and close WinZip.

M3093GX\DG\M3096G\GX\M3097G+\DG
Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI
Win2000\XP Installation Procedure
Rev050304A
12. In the ASPI Twain Download folder locate the setup.exe file and double click.
Afterwards follow the prompts and reboot when finished.
Step H: Installing Scandall21.
1. Create a new folder and name it Scandall Download.
2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.
3. In the sub frame under the Product Support column click on Scanners.
4. On the next page select your Drivers and Downloads.
5. Afterwards click on Software Utilities.
6. Double click on the file name and the File Download box will popup.
7. Click on Save and then use the browse (or other folder navigation) button until you
have the Scandall Download folder you created in the Save In Box.
8. Click Save.
9. When completed close the Download Complete window and go to the Scandall
Download folder.
10. Open the folder and you will see the saved Scandall file. Double click on the file to
unzip it and the WinZip* self-extractor box will popup. Click on browse and select the
Scandall Download folder, then click on Extract. The file will begin to unzip and
when finished a message box will report the number of files unzipped. Click on OK
and close WinZip.
11. In the Scandall Download folder locate the Scandall.exe file and double click.
Afterwards follow the prompts and when finish launch Scandall.
Step I: Scanning with Scandall21.
Once Scandall21 is installed it is time to start scanning.
1. Launch Scandall21 by clicking on the shortcut link on your desktop or manually by
clicking on Start, Programs, Scanner Utility for Microsoft Windows, then
Scandall21.
2. After the Untitled Screen has open, click on Scan and choose Select Source.
3. Select the Fujitsu Twain source for your scanner by highlighting it and clicking
OK. You will only need to do this once unless you are scanning with multiple
sources.
4. Once you are back at the Untitled Screen click on Scan and select To View this
time. The Twain User Interface will popup.
5. Select the scanning parameters that you wish to use – Color mode, resolution,
paper size, etc…
6. Next under Scan Type choose either ADF or Flatbed in the dropdown box.
7. Place your document in the ADF or on the Flatbed face down and click on the Scan
button.
8. After the document is scanned close the Twain User Interface and the image will
appear on the Untitled Screen.
Congratulations! You have successfully completed your scanner installation.
*If you do not have any unzipping software installed on your system, you can download a free
evaluation copy at www.winzip.com.