ADInstruments S7200 User manual

Operation Manual
S7200 TV Signal Analyzer
Ver 1.00

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
I
Warranty
All rights reserved. Reproduction, adaptation, or translation without prior written
permission is prohibited, except as allowed under the copyright laws. The
information contained in this document is subject to change without notice.
Deviser Instruments Inc makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose.
Deviser Instruments Inc shall not be liable for errors contained herein or for
incidental or consequential damage in connection with the furnishing,
performance, or use of this material.
Safety Notices
Observe the following safety precautions whenever you operate any Deviser
Instruments equipment. Failure to comply with these and other specific warnings
and cautions is a violation of Deviser Instruments Inc’ safety standards of design,
manufacturing, and intended use of the measurement device.
Deviser Instruments Inc assumes no liability for the operator’s failure to comply
with these precautions.
Product Damage
Danger! Do not use this product if it shows visible damage, fails to perform, has
been stored in unfavorable conditions, or has been subject to severe

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
II
transportation stresses. Make the product inoperative and secure it against any
unintended operation. Contact your Deviser Instruments Inc representative for
assistance.
Explosion Hazard Danger! Do not operate the instrument in the presence of
flammable gases or fumes.
Electric Shock Hazard Danger! To av oid th e possi bility of s evere inj ury or d eath ,
observe the following precautions when using any Deviser Instruments
equipment:
Do not remove the system covers, and do not perform electrical tests if there are
signs of shipping damage to the outer enclosure.
When connecting test cables to a line, do not touch the cable’s metal contact
points, or allow the cable leads to touch each other.
Use only the supplied power cords and connect only to a properly grounded wall
outlet. Do not use extension cords that do not have a protective ground conductor.
Symbols
The following are general definitions of safety symbols used on equipment and in
manuals.
Dangerous voltage.

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
III
Protective ground.
Frame or chassis ground.
Alternating current
Direct current
Alternating or direct current
Caution! Read the manual
STATEMENT OF FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
IV
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This Deviser Intruments Inc product is warranted against defects in material and
workmanship for a period of 24 months from date of shipment. During the
warranty period, Deviser Instruments Inc will, at its option, either repair or replace
products which prove to be defective.
For warranty service or repair, this product must be returned to an authorized
service center designated by Deviser Instruments Inc. The buyer shall prepay
shipping charges to Deviser Instruments Inc or to the service center and Deviser
Instruments Inc or the service center shall pay the shipping charges to return the
product to . However, the buyer is responsible for all shipping charges, duties, and
taxes, both ways, for products returned to Deviser Instruments Inc or one of it’s
authorized service center that are out of the warranty period.
Deviser Intruments Inc warrants that its software and firmware is designated by
Deviser Intruments Inc for use with Deviser Instrument equipment, and will
execute its programming instructions when properly installed on that instrument.
Deviser Intruments Inc does not warrant that the operation of the instrument, or
software, or firmware will be uninterrupted or error-free but strives to insure the
best operating condition as per specifications and datasheets.
LIMITATION OF WARRANTY

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
V
Unauthorized repair or update, physical damage or improper operational voltage
(at the power supply or RF input) will void this warranty. The main lithium battery
is covered for a period of 1 year.
The foregoing warranty shall not apply to defects resulting from improper or
inadequate use or maintenance by Buyer, Buyer-supplied software or interfacing,
unauthorized modification or misuse, operation outside of the environmental
specifications for the product.
NO OTHER WARRANTY IS EXPRESSED OR IMPLIED. DEVISER INSTRUMENTS INC
SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
VI
Contents
1. Maintenance and Safety Considerations ........................................................ 1
1.1. Calibrating the Meter ......................................................................... 1
1.2. About Battery, Adapter and Firmware upgrade ................................. 2
2. General Introduction ...................................................................................... 4
2.1. Basic Information ............................................................................... 4
2.1.1. Technical S uppo rt & Se rvi ce ...................................................... 4
2.1.2. Manual Abstract ........................................................................ 4
2.1.3. Electrostatic Discharge .............................................................. 5
2.2. Before starting .................................................................................... 6
2.2.1. Overview ................................................................................... 6
2.2.2. Accessories and Options ........................................................... 8
2.3. Recommendations before Using ...................................................... 11
3. Terminology .................................................................................................. 12
4. Instrument Basic Information Introduction .................................................. 22
4.1. Instrument Introduction ................................................................... 22
4.1.1. Front Panel .............................................................................. 22
4.1.2. Top Pan el ................................................................................. 24
4.1.3. Power Supply .......................................................................... 25
4.1.4. Button introduction ................................................................ 28
4.1.5. Touch sc re en operatio n instr uction ........................................ 31
4.2. Main Menu Software Function ......................................................... 36
4.2.1. Main Menu ............................................................................. 36
4.2.2. Title Bar ................................................................................... 36
4.2.3. Function Icon .......................................................................... 38
4.2.4. Status Bar ................................................................................ 38

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
VII
5. Instrument Settings ...................................................................................... 39
5.1. Brief Introduction ............................................................................. 39
5.2. System Information .......................................................................... 39
5.3. General Settings ............................................................................... 40
5.3.1. Network Setting ...................................................................... 41
5.3.2. Ping ......................................................................................... 45
5.3.3. Display & Power ...................................................................... 46
5.3.4. Date & Time ............................................................................ 47
5.3.5. Language ................................................................................. 49
5.3.6. User Management .................................................................. 50
5.3.7. GPS .......................................................................................... 52
5.3.8. Disk Management ................................................................... 54
5.3.9. Restoring Factory Settings ....................................................... 55
5.3.10. Available Option ...................................................................... 56
5.3.11. S7200 System Upgrade Operation Steps ................................. 57
5.4. Measurement Settings ..................................................................... 60
5.4.1. Level Unit ................................................................................ 60
5.4.2. Test Po int Comp ensa tion ........................................................ 61
5.4.3. Adaptive Equalizer .................................................................. 63
5.4.4. Transport Stream Setting ........................................................ 65
5.4.5. Transport Stream Limit Setting ............................................... 69
5.5. Create and Edit a Channel Plan ........................................................ 70
5.5.1. Create Cable and Terrestrial Channel Plan .............................. 70
5.5.2. Export a Channel Plan ............................................................. 73
5.5.3. Edit Channel ............................................................................ 75
5.5.4. Create and Edit Satellite Channel Plan .................................... 85
5.6. External Interface Setup ................................................................... 95

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
VIII
5.6.1. LNB Power Setup ..................................................................... 95
5.6.2. DisEqC Control Signal .............................................................. 98
5.6.3. SaTCR Control Signal ............................................................. 101
5.6.4. ASI Input and Output Control ............................................... 105
5.6.5. Transport Stream Input Control ............................................ 106
5.7. Reviewing & Exporting Files ........................................................... 111
5.7.1. File management .................................................................. 111
5.7.2. Reviewing Files ...................................................................... 114
5.8. File Saving ....................................................................................... 115
6. Measurement Function .............................................................................. 117
6.1. Analog TV Measurement ................................................................ 117
6.1.1. Channel Measurement ......................................................... 117
6.1.2. Analog FM ............................................................................. 119
6.1.3. HUM Modulation .................................................................. 120
6.1.4. Channel Scan ......................................................................... 121
6.1.5. Passive Sweep ....................................................................... 123
6.1.6. Tilt Measurement ................................................................. 125
6.2. Analog Non-linear distortion measurement .................................. 128
6.2.1. Carrier to Composite Noise Ratio Measurement .................. 128
6.2.2. CSO and CTB Measurement .................................................. 131
6.3. Analog TV Video Parameters Measurement .................................. 134
6.3.1. Depth of Modulation ............................................................ 135
6.4. Digital Signal Measurement ........................................................... 136
6.4.1. DVB-C Measurement ............................................................ 137
6.4.2. Digital HUM ........................................................................... 138
6.4.3. Constellation Diagram ........................................................... 140
6.4.4. Error Vector Spectrum (EVS) Function .................................. 142

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
IX
6.5. ATSC (8VSB) measurement ............................................................. 144
6.6. DVB-C2 measurement .................................................................... 150
6.7. DVB-T/H measurement .................................................................. 152
6.8. DVB-T2 measurement .................................................................... 160
6.9. ISDB-TB Measurement .................................................................... 167
6.10. DVB-S/S2 Measurement ................................................................. 170
6.11. Antenna Modify ............................................................................. 174
6.12. Transport Stream Analysis .............................................................. 180
6.12.1. Transport Stream Realtime Analysis ..................................... 181
6.12.2. Basic Information .................................................................. 185
6.12.3. TR 101 290 Priority 1, 2 and 3 Tests ...................................... 186
6.12.4. PID Viewer ............................................................................. 195
6.12.5. PCR Analysis .......................................................................... 196
6.12.6. Program List .......................................................................... 197
6.12.7. PSI/SI Table Analysis .............................................................. 198
6.12.8. PSI/PSIP Table Analysis .......................................................... 203
6.12.9. Data Capture ......................................................................... 209
6.12.10. EPG (Electroic Program Guide) .......................................... 210
6.12.11. Record and Replay Transport Stream ................................. 211
6.12.12. How to use the CA module ................................................ 215
6.13. IPTV Measurement ......................................................................... 217
6.14. Optical Power Measurement and Optical Receiver ........................ 219
6.14.1. Fiber Optical Connector and Adapter Introduction .............. 219
6.14.2. Optical to RF Convertion ....................................................... 221
6.14.3. Optical Power Measurement ................................................ 222
6.15. Forward Spectrum Analysis ............................................................ 224
6.15.1. Frequency Setting ................................................................. 226

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
X
6.15.2. Amplitude Settings ................................................................ 227
6.15.3. RBW & VBW Bandwidth/Sweep Setting ............................... 230
6.15.4. Markers ................................................................................. 234
6.15.5. Trace Setting .......................................................................... 237
6.15.6. Detector Type Setting ........................................................... 239
6.15.7. Display Mode Setting ............................................................ 240
6.16. WiFi Analysis ................................................................................... 244
7. Concept ....................................................................................................... 246
7.1. Unit conversion chart ..................................................................... 246
7.2. Analog TV Standard and Color Transmission System Basic Knowledge
246
7.3. Analog TV Baseband Signal Basic Knowledge ................................. 251
7.3.1. Understanding Composite Video Signal ................................ 251
7.3.2. Interlaced Scanning Concept ................................................ 256
7.4. Gated Measurement Basic Concept ............................................... 258
7.4.1. CCN, C/CSO and C/CTB Gated Measurement ....................... 261
7.5. RBW，VBW .................................................................................... 263
7.6. Detector Mode ............................................................................... 265
7.7. System and Standards by Country .................................................. 268
7.8. USA CATV and DTTB Channel Plan .................................................. 272
7.9. People's Republic of China CATV and DTTB Channel Plan .............. 284
7.10. Europe CATV and DTTB Channel Plan ............................................. 290
7.11. Japan and Brazil Channel Plan ........................................................ 295
8. Specifications .............................................................................................. 308

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
1
1. Maintenance and Safety Considerations
1.1. Calibrating the Meter
All the instruments have analog circuitry: preamplifiers, filter, etc.-whose
performance can change over time. A regular schedule of calibrations will keep
your instrument in optimal condition to support you design, troubleshooting, and
manufacturing work.
It is recommended to calibrate and verify the instrument at least once a year to
ensure that the instrument meets the original designed performance and
specifications.
To avoi d damagi ng the d efaul t calibrat ion data store d in a non-violated memory,
a calibration to the instrument can only be done by an authorized service center
and qualified personnel with appropriate equipment.
For detailed information on the calibration procedures, please contact factory or
authorized distributor.
Environmental condition: Calibration or verification test should be performed
under laboratory condition whereby the ambient temperature or relative
humidity can be controlled.
Warm up: Allow up to at least 5- minutes warm- up before performing calibration
to the instrument. After exposure or storage in a high humidity (condensing)
environment, relative recovery period is required essentially.

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
2
1.2. About Battery, Adapter and Firmware upgrade
Please charge-discharge the battery in every 3 months to extend battery life!
Warning： Danger of explosion if the battery is incorrectly replaced. Replace only
with the same type battery recommended. Do NOT dispose of batteries in a fire.
Do NOT place batteries in the trash. Batteries must be recycled or disposed of
properly.
CAUTION: Recharge the battery only in the instrument. If left unused, a fully
charged battery will discharge itself over time.
Never use a damaged or worn-out adapter or battery. Charging the batteries
internally, even while the analyzer is powered off, the analyzer may keep warm.
To avoid over heat ing , always dis co nnec t the ana lyzer fro m th e AC adapte r befo re
storing the analyzer into the soft carrying case.
CAUTION: Connect the automotive adapter to the power output connector for IT
equipment, when charging the battery on your automotive.
CAUTION: Tempe rat ure extrem es w ill affec t th e abil ity of the battery to ch arge.
Allow the battery to cool down or warm up as necessary before use or charging.
Storing a battery in extreme hot or cold temperatures will reduce the capacity and
lifetime of a battery. Battery storage is recommended at a temperature of less
than 25°C.
The analyzer cannot be used in the standard soft carrying case for more than 1
hours if the ambient temperature is higher than 35°C.
CAUTION: Use only the original AC-DC adapter or originally supplied battery for
the power source.
Whether the instrument work or power off, you can charge the battery.
1 Insert the battery in the analyzer.
2 Plug in the AC-DC adapter and switch on the external power.

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
3
3 The charge indicator lights color is red, indicating that the battery is charging.
When the battery is fully charged, the charging indicator color is green.
The charging time for a fully depleted battery, is approximately four hours.
If the meter is power on, the charging time is longer.
CAUTION: In updating process, there must be a constant power supply to for at
least 60% battery power. If power fails during the updating process it can cause
damage to the instrument.

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
4
2. General Introduction
2.1. Basic Information
2.1.1. Technical Support & Service
This instrument after the sale of two-year warranty，before the two-year warranty
expires, users can purchase an extended warranty period of one year; battery
warranty for one year. Depending on number of units purchased, customers can
receive initial on site training from our technical support engineers in a “train the
trainer” format. Our application engineers can also answer questions and on
going technical support regarding software or equipment.
For special applications, Deviser instruments offers custom software design at an
extremely competitive rate and time to market.
On going development and “maintenance engineering” is provided on all
products and yearly maintenance programs are offered to insure customers can
fully benefit from the latest upgrades available for their products. Technical
documents and applications guides are released and available on an on-going
basis.
2.1.2. Manual Abstract
Thank you for choosing the S7200 TV Signal Analyzer. This manual will familiarize
you with all measurement capabilities of this instrument.
The manual is divided into 8 sections:
Section I Maintenance and Safety Considerations
Section II: General Introduction

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
5
Section III: Terminology
Section IV: Basic information and introduction to external characteristics
Section V: Settings, Introduction of measurement and general settings
Section VI: Measurements, detailed steps and operations for all measurement
functions
Section VII: Concepts, Explanations of important new technologies introduced in
this instrument
Section VIII: Specifications
2.1.3. Electrostatic Discharge
An electrostatic discharge may damage the instrument, so it should be used in
electrostatic free environment. These safeguards will provide guidance in
reducing and avoiding ESD instances during normal use of the instrument:
l When connecting a coaxial cable to the instrument for the first time every
day, the center conductor of the cable and the outer braided shielding layer
should connect to the ground instantly.
l While servicing the unit, insure that the technician is grounded before
removing inner parts or component, or pulling out connecting cables.
l Make sure the instrument is well grounded so not to store any static charges.
l Electrostatic protection of this instrument is up to standards of 6KV contact
and 8KV air-gap.

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
6
2.2. Before starting
2.2.1. Overview
S7200 is a high performance TV signal analyzer. S7200 has fast spectrum analysis
function, support multi cable, terrestrial and satellite digital TV standards: DVB-
C/C2, DVB-S/S2, DVB-T/T2, ATSC, ISDB-Tb. The TV analyzer also support multi type
video encoding format, example MPEG2/4, H.264, VC-1 and HD and SD image
decoding, example 1080p, 720p or 576i. S7200 provide DVB-CI option, user can
use this option decode the encryption program. For analog TV, S7200 support
NTSC, PAL, SECAM standard.
More and more countries use the 700MHz as LTE service, the LTE signals has effect
the same frequency band CATV signals. S7200 provide time domain EVS function,
user can use this function check LTE interference without interruption of service.
S7200 support RF and ASI port input signals do transport stream analysis, also
support SATA SSD or USB disk transport stream record and playback function.
Many users began using optical LNB, so S7200 provide optical power meter and
optical receiver option.
S7200 also provide IPTV function, WiFi analysis function and GPS dongle.
The capacitive touch screen is a major of S7200. User experience is grealty
enhance, especially in the function of spectrum analysis.

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
7
Key Features:
l All standards in one: S7200：DVB-C (J.83A/B/C)/C2, DVB-T/H/T2, DVB-
S/S2, ATSC, ISDB-T
l Digital/Analog TV and Digital Satellite TV analysis
l MPEG2 Transport stream analyzer and monitoring via TS-ASI input
&RF input
l Fast spectrum analysis with 5 ~ 2150 MHz frequency, Max span
1215MHz
l DSP Technology to support different video decoding: MPEG-2, MPEG-
4, H.264, VC-1 for 1080p, 720p and 576i, support PAL/NTSC/SECAM
color system
l Support SD&HD Video format
l CAM module (Conditional Access) for encrypted channels
l TS-ASI input and output
l IPTV analysis option
l TS record and TS replay, Very High speed (>95Mbps) Transport Stream
record & analysis
l Optical Power measurement and Optical Receiver option
l Double 1000M LAN and USB interface
l Inside WiFi option
l Outside GPS Dongle option
l Capacitive Touch Sc re en, High resolution touch 7" TFT LCD with bright
display for indoors and outdoors Easy to use

AD INSTRUMENTS S7200 TV Signal Analyzer Operation Manual
8
2.2.2. Accessories and Options
If user want ordering S7200, he must choose a basic model, base on the basic
model continue to choose options.
S7200 (the basic functions include: DVB-C (J.83 Annex A/C)，DVB-S/S2，DVB-T/H，
DVB-T2，ASI Input and Output)
S7200-ISDB (the basic functions include: DVB-C (J.83 Annex A/C)，DVB-S/S2，DVB-
T/H，DVB-T2，ISDB-Tb，ASI Input and Output)
S7200-ATSC (the basic functions include: DVB-C（J.83 Annex A/B/C）， DVB-S/S2，
DVB-T/H，DVB-T2，ATSC，Spectrum Emission Mask，ASI Input and Output)
No.
Type
Name/Description
Model
Order
number
1
Instrument
TV Signal Analyzer
S7200
0110.7200.00
2
Instrument
TV Signal Analyzer
S7200-ISDB
0110.7200.01
3
Instrument
TV Signal Analyzer
S7200-ATSC
0110.7200.02
4
Accessory
S7200 English
Calibration
Certification
S7200-000
6110.0600.40
5
Accessory
TOKO Type-F(f) to
Type-F(f) adapter
SFL10-KK
6190.0500.01
6
Accessory
S7200 Carrying Case
S7200-001
6110.0600.41
7
Accessory
CD (Toolbox
Software and
Operation Manual)
S7200-002
6110.0600.42