ADTRAN NetVanta 1000 Series Manual

NetVanta 1000 Series Switch
Hardware Installation Guide
1200500L1 NetVanta 1224
1200504L1 NetVanta 1224ST
1200510L1 NetVanta 1224STR
1200520L1 NetVanta 1224R
61200500L1-34C
July 2004

Trademarks NetVanta 1000 Series Switch Hardware Installation Guide
2 © 2004 ADTRAN, Inc. 61200500L1-34C
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
© 2004 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.

NetVanta 1000 Series Switch Hardware Installation Guide Conventions
61200500L1-34C © 2004 ADTRAN, Inc. 3
Conventions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the equipment or
endangerment to human life.

Safety Instructions NetVanta 1000 Series Switch Hardware Installation Guide
4 © 2004 ADTRAN, Inc. 61200500L1-34C
Safety Instructions
When using your telephone equipment, please follow these basic safety precautions to reduce the risk of
fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
5. The socket-outlet shall be installed near the equipment and shall be easily accessible.
Save These Important Safety Instructions
Double pole/neutral fusing.

NetVanta 1000 Series Switch Hardware Installation Guide FCC-Required Information
61200500L1-34C © 2004 ADTRAN, Inc. 5
FCC-Required Information
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could effect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an FCC-
compatible modular jack, which is compliant with Part 68 and requirements adopted by ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
8. The REN is useful in determining the quantity of devices you may connect to your telephone line
and still have all of those devices ring when your number is called. In most areas, the sum of the
RENs of all devices should not exceed five. To be certain of the number of devices you may
connect to your line as determined by the REN, call your telephone company to determine the
maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
Part Number
Registration
Number Service Type REN/SOC FIC USOC
1200861L1 US:HDCDENAN1200861L1 56 Kbps Digital Interface
64 Kbps Digital Interface
6.0F 04DU5-56
04DU5-64
RJ-48S
1200862L1 US: HDCDENAN1200863L1 1.544 Mbps - SF
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
6.0N
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
RJ-48C
1200863L1
1202862L1 US: HDCDENAN1202863L1
1202863L1
1200872L1 US: HDCDENAN1200872L1
1200864L1 US: HDCM504A1200864L1 Analog Loop Start 0.4A/9.0F 02LS2 RJ-11C
1200865L1 US: HDCDENAN1200865L1 Basic Rate ISDN 6.0F 021S5 RJ-49C

FCC Radio Frequency Interference Statement NetVanta 1000 Series Switch Hardware Installation Guide
6 © 2004 ADTRAN, Inc. 61200500L1-34C
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Electromagnetic Compatibility (EMC) Table for the NetVanta 1224STR/1224R
NetVanta Module P/N and Name NetVanta 1224STR/1224R
1200861L1 56K/64K NIM FCC Part 15, Class A
EN55022 Class A
1200862L1 T1/FT1 NIM FCC Part 15, Class A
EN55022 Class A
1202862L1 T1/FT1 NIM, 2nd Gen FCC Part 15, Class A
EN55022 Class A
1200863L1 T1/FT1+DSX-1 NIM FCC Part 15, Class A
EN55022 Class A
1202863L1 T1/FT1+DSX-1 NIM, 2nd Gen FCC Part 15, Class A
EN55022 Class A
1200866L1 Serial NIM FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200867L1 SHDSL NIM FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200864L1 Analog Modem DIM FCC Part 15, Class A
EN55022 Class A
1200865L1
1200875L1
ISDN BRI DIM
ISDN S/T DIM
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200868L1 E1/FE1 NIM FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200872L1 Dual T1 NIM FCC Part 15, Class A
EN55022 Class A
1200878L1 E1/FE1 w/ G.703 Drop FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1202368L1 VPN Accelerator Card FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3

NetVanta 1000 Series Switch Hardware Installation Guide Industry Canada Compliance Information
61200500L1-34C © 2004 ADTRAN, Inc. 7
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the “IC:” in front
of the certification/registration number) signifies that the Industry Canada technical specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the documentation or on
the product labeling/markings. The REN assigned to each terminal device indicates the maximum number of
terminals that can be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the RENs of all the devices should not exceed
five (5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.

Affidavits NetVanta 1000 Series Switch Hardware Installation Guide
8 © 2004 ADTRAN, Inc. 61200500L1-34C
Affidavits
Affidavit Requirements for Connection to Digital Services
• An affidavit is required to be given to the telephone company whenever digital terminal equipment without
encoded analog content and billing protection is used to transmit digital signals containing encoded analog content
which are intended for eventual conversion into voiceband analog signals and transmitted on the network.
• The affidavit shall affirm that either no encoded analog content or billing information is being transmitted or that
the output of the device meets Part 68 encoded analog content or billing protection specifications.
• End user/customer will be responsible for filing an affidavit with the local exchange carrier when connecting
unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.
• Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit requirement
for subrate services is waived.

NetVanta 1000 Series Switch Hardware Installation Guide Affidavits
61200500L1-34C © 2004 ADTRAN, Inc. 9
Affidavit for Connection Of Customer Premises Equipment to 1.544 Mbps And/or Subrate Digital
Services
For the work to be performed in the certified territory of ___________________(telco name)
State of ________________
County of ________________
I, _______________________ (name), _____________________________(business address),
____________________ (telephone number) being duly sworn, state:
I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or ________ subrate
digital services. The terminal equipment to be connected complies with Part 68 of the FCC rules except for the encoded analog content and
billing protection specifications. With respect to encoded analog content and billing protection:
( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to analog content
and encoded billing protection information continuously complies with Part 68 of the FCC Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended to be decoded
within the telecommunications network.
( ) The encoded analog content and billing protection is factory set and is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the
encoded analog content and billing information has (have) been trained to perform these functions by successfully having completed one
of the following (check appropriate blocks):
( ) A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or
( ) A training course provided by the customer or authorized representative, using training materials and instructions provided by the
manufacturer/grantee of the equipment used to encode analog signals; or
( ) An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the equipment used to
encode analog signals; or
( ) In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a supervisor trained in accordance with
_________ (circle one) above.
I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as
provided in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of _______________, _______
_________________________________
Notary Public
My commission expires:
_________________________________

FCC Radio Frequency Interference Statement NetVanta 1000 Series Switch Hardware Installation Guide
10 © 2004 ADTRAN, Inc. 61200500L1-34C
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.