Advantech ECU-P1628D Installation and operation manual

STARTUP MANUAL
1 Startup Manual
ECU-P1618D/1628D
8-port RS-232/422/485 with and without port-to-port Isolation for UNO-4673A/4683 and ECU-4784
Packing List
Before installation, make sure that you have the ECU-
P1618D/1628D suit which includes the card and panel
as below.
Diagram
iOverviewation
ECU-P1618D/1628D are 8 serial ports cards, with the
following specifications::
8-port RS-232/422/485
Automatic RS-485 data flow control
2,000 VDC Isolation Protection (ECU-P1628D)
IRQ: All use the same IRQ assigned by PCI Bus
Data bits: 5, 6, 7, 8
Stop bits: 1, 1.5, 2
Parity: None, Even, Odd
Baud-rate (bps):
–RS-232: 50~115.2 k
–RS-422/485: 50~921.6 k
Transmission Distance: 1000 m (RS-422/485)
Data Signals:
–RS-232: DCD,RxD,TxD,DTR,GND,DSR,RTS
,CTS,RI
–RS-485: Data+, Data-, GND
–RS-422: Tx+, Tx-, Rx+, Rx-, GND
Installation
The ECU-P1618D/1628D are expansion cards for
the UNO-4673A/4683 and ECU-4784 which has 3
expansion slots, the ECU-P1618D/1628D can be
plugged into any of the 3 slots in the UNO-4673A/4683
and ECU-4784. Follow these steps to integrate into the
UNO-4673A/4683 and ECU-4784:
Select one of the slots: unscrew the two screws on
the blank panel of the slot then remove the blanking
plate.
Plug the ECU-P1618D/1628D into the selected slot
of the UNO-4673A/4683 and ECU-4784 carefully
and fix it by the two screws on the panel.
Notes
For more information on this and other Advantech
products, please visit our websites at:
http://www.advantech.com
http://www.advantech.com/eAutomation
For technical support and service:
http://www.advantech.com.tw/eservice
This manual is for ECU-P1618D/1628D
Part No: 2003SP0500 1st Edition
April 2016
Bracket panel
Insulation mylar
ScrewPlug in card
If anything is missing or damaged, contact your
distributor or sales representative immediately.
12345
6789
Pin RS-232 RS-422 RS-485
1 DCD TX- Data-
2 RxD TX+ Data+
3 TxD RX+
4 DTR RX-
5 GND GND GND
6 DSR
7RTS
8 CTS
9 RI
ECU-P1618D/1628D serial ports COM1~COM8
Pin Assignment

STARTUP MANUAL
Startup Manual 2
8-port RS-232/422/485 with and without port-to-port Isolation for UNO-4673A/4683 and ECU-4784
COM Port Conguration
Please follow the below description to set the COM ports,
please also refer to the UNO-4673A/4683’s user manual
for detailed function description:
1. Selection of RS-232 or RS-422/485
COM Port Jumper COM Port Jumper
COM1 CN3 COM5 CN7
COM2 CN4 COM6 CN8
COM3 CN5 COM7 CN9
COM4 CN6 COM8 CN10
RS-232 Jumper Setting (Default)
LED Indicators
There are LED indicators on the front panel of UNO-
4673A/4683 and ECU-4784 for indicating the system
running status. You can know the COM status of ECU-
P1618D/1628D by the consistent slot LED indicators.
2. Switch the RS-485 auto-flow control or RS-422
Master/Slave mode (SW1)
COM Port DIP of SW1
COM1 DIP1
COM2 DIP2
COM3 DIP3
COM4 DIP4
COM5 DIP5
COM6 DIP6
COM7 DIP7
COM8 DIP8
SW1 Status Description
0 RS-422: Master mode
RS-485: N/A
1 (Default) RS-422: Slave mode
RS-485: Auto flow control
3. Setting the Terminal Resistor
COM Port Jumper COM Port Jumper
COM1 JP1 COM5 JP5
COM2 JP2 COM6 JP6
COM3 JP3 COM7 JP7
COM4 JP4 COM8 JP8
Short Description
1-3 Add 120 Ohm terminal resistor on Tx+/Tx- of RS-422
or Data+/Data- of RS-485
3-5 Add 300 Ohm terminal resistor on Tx+/Tx- of RS-422
or Data+/Data- of RS-485
2-4 Add 120 Ohm terminal resistor on Rx+/Rx- of RS-422
4-6 Add 300 Ohm terminal resistor on Rx+/Rx- of RS-422
LED No. COM Status
1 COM1 Tx
2 COM1 Rx
3 COM2 Tx
4 COM2 Rx
5 COM3 Tx
6 COM3Rx
7 COM4 Tx
8 COM4 Rx
9 COM5 Tx
10 COM5 Rx
11 COM6 Tx
12 COM6 Rx
13 COM7 Tx
14 COM7 Rx
15 COM8 Tx
16 COM8 Rx
RS-422/485 Jumper Setting