Advantech PCE-5B12-07 Installation and operation manual

PCE-5B12(7B13)-07 Startup Manual 1
Before you begin installing your card, please make sure
that the following materials have been shipped:
• One 2 Ports USB Cable P/N: 1700002204
• PCE-5B12(7B13)-07 Startup Manual
• M4*6*0.7 Round Screws (20 pieces) P/N: 1939000410
• 2-year quality warranty card P/N: 2190000902
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
PCE-5B12(7B13)-07 Backplane: 12(13)-slot BP for 14-Slot
Chassis, 1 PICMIG 1.3, 4(5) PCIe, 7 32-bit/33-MHz PCI
Startup Manual
Standard functions
• PICMG 1.3 Slot:
PCE-5B12-07 supports PCE-5XXX CPU Cards
PCE-7B13-07 supports PCE-7XXX CPU Cards
• PCIe Slots:
PCE-5B12-07: 1 PCIe x16, 3 PCIe x4
PCE-7B13-07: 2 PCIe x8, 3 PCIe x4
• 32-bit PCI Slots:
PCE-5B12-07: 7 32-bit/33-MHz PCI
PCE-7B13-07: 7 32-bit/33-MHz PCI
• USB (2.0) support: Four Universal Serial Bus ports to
Backplane
Note: Some add-on cards installed on this backplane
may cause CPU card BIOS resource allocation
problems, if this occurs please contact Advan-
tech technical support staff for help in solving the
problems.
Mechanical and Environment
• Dimensions: 327.66 x 315.45 mm
• Power supply voltage: +12 V, +5 V, -12 V, -5 V, +5 V
SBY, +3.3 V
• Power requirements: Depends on the CPU board, addon
card & peripherals
• Operating temperature: 0 ~ 60° C
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the PCE-5B12-07A1E(PCE-7B13-
07A1E) series.
Part No. 200K5B1211
Pr i n t e d i n C h i n a
2nd Edition,
August 2012

2 PCE-5B12(7B13)-07 Startup Manual
Connectors and Jumpers
This table shows the function of each jumper and connector:
Connectors
Label Function
SHBA1~SHBD1
PICMG1.3 CPU board slot
PPCIE2 PCIe x 16 slot (Only on PCE-
5B12-07)
PPCIE1, PPCIE2 PCIe x8 slots (Only on PCE-
7B13-07)
P1PCIE1~P1PCIE3 PCIe x4 slots
P1PCI1~ P1PCI3 32 Bit / 33 MHz PCI Bus slots
P2PCI1~P2PCI4
32 Bit / 33 MHz PCI Bus slots
EATXPWR1 ATX2.0 24-pin Power Connector
EATX12V1 ATX 12V Auxiliary 8-pin Power
Connector
ATX12V1 ATX 12V 4-pin Power Connector
PWR3V1 3.3V Auxiliary Power Connector
PWR3V2 3.3V Auxiliary Power Connector
VOLT1 Alarm board / CMM Power Con-
nector
FAN1~6 FAN Connector (Horizontal Type)
FAN7 FAN Connector (Vertical Type)
FANDEC1 FAN speed detector Connector
(Optional)
SMBUS1~SMBUS3 System Management Bus
(Optional)
JFP1 Power and Reset button Con-
nector
IPMB1 IPMB Connector (Optional)
USB12 Two USB port pin header
USB34 Two USB port pin header
Note: In this backplane’s default conguration, FAN-
DEC1, SMBUS1~SMBUS3, IPMB1 pin-headers
are NOT populated, those footprints are reserved
for customization.
Jumpers
Label Function
PSON1
ATX / AT Mode Selection
EATXPWER1
Pin Name
1
3.3 V
2 3.3 V
3GND
45 V
5GND
6
5 V
7GND
8 Power OK
9
5 V SBY
10
12 V
11 12 V
12 3.3 V
13 3.3 V
14 -12 V
15 GND
16 PSON#
17 GND
18 GND
19 GND
20 -5 V
21 -5 V
22 5 V
23 5 V
24 GND
ATX12V1
Pin Name
1
GND
2 GND
312 V
4 12 V

PCE-5B12(7B13)-07 Startup Manual 3
FANDEC1
Pin Name
1
FANIO1
2 FANIO2
3FANIO3
4 FANIO4
5FANIO5
6
FANIO6
7FANIO7
SMBUS1~SMBUS3
Pin Name
1
5 V
2 C-SMBBUS
3C-SMBDAT
4 GND
IPMB1
Pin Name
1
IPMB_CLK
2 IPMB_DAT
3GND
USB12
Pin Name
1
USBV0
2 USBV0
3USBD0-
4 USBD1-
5USBD0+
6
USBD1+
7GND
8 GND
9
Null
10
GND
EATX12V1
Pin Name
1
GND
2 GND
3GND
4 GND
512 V
6
12 V
712 V
8 12 V
PWR3V1 & PWR3V2
Pin Name
1
3.3V
2 3.3V
3 3.3V
4 GND
5GND
6
GND
VOLT1
Pin Name
1
5 V SBY
2 GND
3GND
4 -5 V
55 V
6
3.3 V
7-12 V
8 12 V
FAN1~FAN7
Pin Name
1
GND
2 12 V
3FANIO1~FANIO7

123
4 PCE-5B12(7B13)-07 Startup Manual
USB34
Pin Name
1
USBV2
2 USBV2
3USBD2-
4 USBD3-
5USBD2+
6
USBD3+
7GND
8 GND
9
Null
10
GND
PSON1: ATX / AT Mode Selection
Setting Function
1-2
AT Mode
2-3* ATX Mode
* Default
JFP1
Pin Name
1
VCC
2 PWRBTN
3RESET#
4 GND
123

PCE-5B12(7B13)-07 Startup Manual 5
Board Layout
Figure 1: Board Layout
Note: 1. Some add-on cards installed on this backplane may cause CPU card BIOS resource allocation problems, if this
occurs please contact Advantech technical support staff for help in solving the problems.
2. In this backplane’s default conguration, FANDEC1, SMBUS1~SMBUS3, IPMB1 pin-headers are NOT populated,
those footprints are reserved for customization.
PPCIE1
PPCIE2
P1PCI1
P1PCI2
P1PCI3
P1PCIE1
P1PCIE2
P1PCIE3
P2PCI1
P2PCI2
P2PCI3
P2PCI4
USB34 USB12
IPMB1
EATXPWR1
EATX12V1
ATX12V1
FAN4
FAN3
SMBUS3 FAN6
FAN5
SMBUS1 FAN1 FAN2 PSON1
PWR3V2 PWR3V1
FANDEC1
VOLT1
SMBUS2 FAN7

6 PCE-5B12(7B13)-07 Startup Manual
Board Diagram
Figure 2: Board Dimensions
Board Dimensions

PCE-5B12(7B13)-07 Startup Manual 7
Figure 3: Board Diagram
Board Diagram
32-bit/33MHz P2PCI
X4
X8
X8
USB X4
SATA X2
LAN X2
IPMB X1
32-bit/33MHz P1PCI
PCIe Packet
Switch
PCI to PCI
Bridge

8 PCE-5B12(7B13)-07 Startup Manual
Board Diagram
PCI 32-bit from ICH
PCI Interrupt
Pin Route
PCI Slot PPCI1 PPCI2 PPCI3
IDSEL AD31 AD30 AD29
INTA INTB INTC INTD
INTB INTC INTD INTA
INTC INTD INTA INTB
INTD INTA INTB INTC
PCI 32-bit from Switch
PCI Interrupt
Pin Route
PCI Slot P2PCI1 P2PCI2 P2PCI3 P2PCI4
IDSEL AD20 AD21 AD22 AD23
INTA INTA INTB INTC INTD
INTB INTB INTC INTD INTA
INTC INTC INTD INTA INTB
INTD INTD INTA INTB INTC
PCI Routing Table

PCE-7B13-64C1E(PCE-5B12-64C1E) Startup Manual 1
PCE-7B13-64C1E(PCE-5B12-64C1E) PICMG
1.3 Backplane 13(12)-slot BP for 14 slots
Chassis, 2(1) PCIe, 6 64-bit PCI-X, 4 32-bit PCI
Startup Manual
Before you begin installing your card, please make
sure that the following materials have been shipped:
If any PCE-7B13-64C1E(PCE-5B12-64C1E) of these
items are missing or damaged, contact your distribu-
tor or sales representative immediately.
Standard Functions
• PICMIG 1.3 slots:
PCE-7B13-64 supports PCE-7xxx CPU boards
PCE-5B12-64 supports PCE-7XXX/5XXX CPU boards
•
PCIe slots:
PCE-7B13-64 Supports two PCIe x8 slot
PCE-5B12-64 Supports one PCIe x16 slot
•
64-bit PCI-X slots:
Four 64 Bit / 66Mhz PCI-X slot
Two 64 Bit / 100Mhz PCI-X slot
•
32-bit PCI:
Four 32 Bit / 33 Mhz PCI slot
• USB
(2.0) support: Four Universal Serial Bus ports to Back-
plane
Mechanical and Environment:
• Dimensions: 327.66 x 297.67 mm
• Power supply voltage: +12V, +5V, -12V, -5V, +3.3V,
+5VSBY
• Power requirements: Refer to the CPU Board , add-on
Card & Peripherals
• Operating temperature:
0 ~ 60°C
• Weight: 0.6kg (weight of board)
The backplane has a number of connectors and jumpers
that allow you to configure your system to suit your appli-
cation. The table below lists the function of each of the
connectors and jumpers.
Connectors
Jumpers
Packing list
• One 2 Ports USB Cable p/n: 1700002204
• PCE-7B13-64C1E(PCE-5B12-
64C1E) Startup Manual
• M4*6*0.7 Round Screws [15 pcs.]
p/n: 1939000410
• 2 years quality warranty card p/n: 2190000902
For more information on this and other Advantech prod-
ucts, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our support
website at:
http://www.advantech.com/support
This manual is for the PCE-7B13(5B12)-64B1E series
Rev. C1.
Part No. 20027B1303
Printed in China 4th Edition Aug. 2014
Connectors and Jumpers
Part
Reference Function
SHBA1~SHBD1PICMG 1.3 CPU board slot
PPCIE1 PCE-7B13-64: PCIe x8 slot
PCE-5B12-64: Not Available
PPCIE2 PCE-7B13-64: PCIe x8 slot
PCE-5B12-64: PCIe x16 slot
P1PCIX1~
P1PCIX4 64 Bit / 66MHz PCI-X Bus Slot (Primary 1)
P2PCIX1,
P2PCIX2 64 Bit / 100MHz PCI-X Bus Slot (Primary 2)
PPCI1~PPCI4 32 Bit / 33MHz PCI Bus Slot (Primary 3)
EATXPWR1 ATX2.0 24-Pin Power connector
EATX12V1 ATX 12V Auxiliary 8-pin power connector
ATX12V1 ATX 12V 4-pin power connector
PWR3V1 3.3V Auxiliary power connector
PWR3V2 3.3V Auxiliary power connector
VOLT1 Alarm board/CMM Power connector .
FAN1 FAN Connector
FAN2 FAN Connector
FAN3 FAN Connector
FAN4 FAN Connector
FAN5 FAN Connector
FAN6 FAN Connector
FAN7 FAN Connector
FANDEC1 Fan speed detector connector
SMBUS1 SMBus connector for chassis monitor
SMBUS2 SMBus connector for chassis monitor
JFP1 Power and Reset Button connector
IPMB1 IPMB Connector
USB12 Two USB port pin header
USB34 Two USB port pin header
Part
Reference Function
JP1VIO1 Primary 1 PCI-X Bus VIO voltage selection
JP2VIO1 Primary 2 PCI-X Bus VIO voltage selection
JM66ENA1 Primary 1 PCI(-X) Bus capability selection
JPCIXCAPA1 Primary 1 PCI Bus freq. selection
JM66ENB1 Primary 2 PCI Bus freq. selection
JPCIXCAPB1 Primary 2 PCI(-X) Bus capability selection
PSON1 ATX/AT mode selection
PCE-7B13-64C1E(PCE-5B12-64C1E) Backplane: 13(12)-slot BP for 14 slots Chassis, 1 PICMIG 1.3, 2(1) PCIe, 6 64-bit PCI-X, 4 32-bit PCI

2 PCE-7B13-64C1E(PCE-5B12-64C1E) Startup Manual
Board Layout: Jumper and Connector Locations
Board Layout
P1PCIX1 P1PCIX3 P2PCIX1 PPCI1 PPCI3
P1PCIX2 P1PCIX4 P2PCIX2 PPCI2 PPCI4
EATXPWR1
PWR3V1
PWR3V2
VOLT1
JP1VIO1 JP2VIO1
PPCIE1
PPCIE2
FAN7
SHBA1
SMBUS2
USB12
USB34
FANDEC1
IPMB1
JFP1 SMBUS1 FAN2
FAN1 PSON1
EATX12V1
ATX12V1 FAN4
D182,D184,D183,D185
Fan3
3
4
3
4
,
, ,
,
FAN5 FA N6
JM66ENB1
JPCIXCAPB1
JM66ENA1
JSEL100A1
JPCIXCAPA1
D146,D147,D148,D149