Advantech PCA-6154 Installation and operation manual

PCA-6154/6154L StartupManual 1
PCA-6154/6154L Half-size Pentium®
CPU Card SBC with VGA/Ethernet
PCA-6154/6154L Half-size all-in-one Pentium®
CPU Card with VGA and Fast Ethernet
Startup Manual
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/epc
For technical support and service, please visit our
support website at:
http://support.advantech.com
This manual is for the PCA-6154/L series Rev.A1
Part No. 2006615410 1st Edition
Printed in Taiwan Dec. 1999
Packing List
Before you begin installing your card, please make surethat
the following materials have been shipped:
• 1 PCA-6154/6154L all-in-one single board computer
• 1 hard disk drive (IDE) interface cable (40 pin)
p/n: 1701400601
• 1 floppy disk drive interface cable (34 pin)
p/n: 1701340700
• 1 parallel port adapter (26 pin) and COM2 adapter (9 pin)
p/n:1701260303
• 1 USB cable p/n: 1703100260
• 1 CPU fan with heatsink
• 1 6-pin mini-DIN keyboard & PS/2 mouse adapter
p/n:1700060201
• 1 startup manual
• CD-ROM or disks for utility, drivers, and manual (in PDF
format)
• 1 warranty certificate
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Note 1: For detailed contents of the PCI-6154/L, please
refer to the enclosed CD-ROM or disk (in PDF
format).
Note 2: Acrobat Reader is acquired to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/Prodindex/acrobat/
readstep.html
(Acrobat is a trademark of Adobe.)
Specifications
Standard SBC Functions
•CPU: Intel Pentium® 100 ~ 233 MHz, Pentium MMX,
AMD K5, AMD K6 200 / 266 MHz, AMD K6-2 266 ~ 300
MHz, Cyrix M1, Cyrix M2 up to PR-300 MHz, or IDT Win
Chip C6 upto 200 MHz
•BIOS: Award 256 KB (2 Mbit) memory; supports plug
and play, suspend to disk
•Chipset: SiS5598
•L2 cache: On-board 512 KB synchronous (pipeline
burst) SRAM
•Green function: Features power management option
via BIOS, activated by keyboard or mouse activity.
Supports doze, sleep and suspend modes. APM 1.1
compliant
•RAM: Two 72-pin SIMM sockets. Supports 32-bit FPM or
EDO DRAM with memory capacity from 8 ~ 128 MB.
•EIDE interface: Handles up to two IDE HDDs or other
IDE devices. Supports PIO mode 4 and Ultra DMA mode
•FDD interface: Supports up to two floppy disk drives.
•Parallel port: Configured to LPT1, LPT2, LPT3 or
disabled.
Supports multi-mode parallel port (SPP/ECP/EPP)
•Serial ports: Two 16C550 UARTs, one RS-232, one
RS-232/422/485 interface
•Watchdog timer: Can generate a system reset.
Software enabled/disabled.Time interval is from 1 to 62
seconds, jumperless with run-time setup
•Keyboard/mouse connector: 6-pin mini-DIN connector
on the mounting bracket eases connection to a
keyboard or PS/2 mouse. An on-board keyboard pin
header connector is also available.
•I/O bus expansion: PC/104 connector with face-up
installation
•USB interface: Two USB connectors with fuse
protection. Complies with USB specification 1.0
•Infrared port: Fast IrDA.Transfer rate up to 4 Mbps. I/O
port programmable to COM1 (3F8), COM2 (2F8),
COM3 (3E8) or COM4 (2E8).
VGA interface
•Chipset: SiS5598 built-inVGA function
•Architecture: Universal memory architecture
•Display memory: Share system RAM 1 MB ~ 4 MB
100Base-T Ethernet interface (PCA-6154 only)
•Chipset: REALTEK RTL8139. PCI bus 100/10 Mbps
Ethernet

2PCA-6154/6154L StartupManual
Locating Jumpers
Locating connectors (component side)
Jumpers and Connectors
Specifications Cont.
controller
• I/O address jumperless setting
• Built-in boot ROM
SSD function
• Supports M-Systems' DiskOnChip®2000 Flash disk up
to 144 MB
Mechanical and environmental specifications
•Board size: 185 x 122 mm
•Max. power requirements: +5V @ 5.5 A, +12 V @ 100
mA
•Operating temperature: 0 ~ 60° C (32 ~ 140° F)
•Board weight: 0.5 kg (1.2 lbs)
PCA-6154/6154L jumpers
Number Function
JP2 CPU clock ratio select
JP3 CPU core voltage select
JP4 Watchdog timer select
JP5 Real-time clock (RTC) power and CMOS
select
JP7 DiskOnChip®2000 Flash disk memory
segment
JP8 COM2 RS-232/422/485 selection
JP9 CPU clock select
JP10 CPU clock optimize enable
Table 1-2: PCA-6154/6154L connectors
Number Function
CN1 IDE port
CN2 Floppy disk connector
CN3 Parallel port
CN4 CPU fan power connector
CN5 Infra red port
CN6 Main power connector
CN7 VGA connector
CN8 100/10 Mbps network connection
(PCA6154 only)
CN9 USB 1 and USB 2 ports
CN10 COM2 port
CN11 COM1 port
CN12 PC/104 A1~ A32, B1~ B32
CN13 PC/104 C1~ C20, D1~ D20
CN14 External keyboard
CN15 Keyboard and PS/2 mouse
CN16 Front panel connector
CN17 HDD LED
Locating jumpers (component side)
Main
USB
COM2
Eth- ernet
VGA
FIR
Par-
allel
Front
panel
Flop-
py
CPU
fan
IDE
hard
HDD
SIMM
(Bank
SIMM
(Bank
PC/ PC/ Exter-
nal
COM1
Key- board
CPU DOC
2000
JP9
JP3JP2 JP4
JP7
JP8
JP10
JP5

PCA-6154/6154L StartupManual 3
CPU clock ratio select (JP2)
Pentium CPU, AMD K5, K6, Cyrix M1, IDT C6
100 MHz 166 MHz
1.5 x 66 2.5 x 66
*133 MHz 200 MHz
2 x 66 3 x 66
150 MHz 233 MHz
2 x 75 3.5 x 66
266 MHz 300 MHz
4 x 66 4.5 x 66
* default setting
Refer to the CPU speed reference table (below) for
instructions on adjusting the internal clocks according to
the base CPU speed.
CPU speed reference table
CPU Speed (MHz) 100 *133 150 166 200 233 266 300
Clock setting 66 66 75 66 66 66 66 66
Frequency ratio 1.5 2 2 2.5 3.0 3.5 4 4.5
* default setting
System/PCI clock setting (JP9)
System (MHz) *66 75
PCI (MHz) 33 37.5
JP9
* default setting
CPU voltage select (JP3)
Pentium CPU, AMD K5, K6, Cyrix M1, M2, IDT C6
1.9V 2.0V
2.2V 2.3V
2.4V 2.5V
2.6V 2.5V
2.8V 2.9V
3.0V 3.1V
3.2V 3.27 V
*3.3 V 3.45 V
* default setting
Watchdog timer system reset select (JP4)
*System Reset IRQ15
JP4
1
)8PJ(584/224/232-SRrofsgnittes2MOC
desolcsniP232-SR*224-SR584-SR
2-1noffoffo
4-3ffonono
6-5ffoffono
8-7ffonono
9-7no--
21-01- nono
21-11no--
41-31- no-
51-31no--
81-61- no-
81-71no--
* default setting
DOC2000 address setting (JP7)
Address JP7
Disable
D800-D9FF
*D000 ~ D1FF
E000 ~ E1FF
CC00 ~ CDFF
DC00 ~ DDFF
D400 ~ D5FF
* default setting
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
11
1

4PCA-6154/6154L StartupManual
PCA-6154 Mechanical Drawing
mechanical drawing (component side)
RTC power and CMOS clear (JP5)
*Normal CMOS data clear
JP5
* default setting
DLL circiut for CPU clock optimization (JP10)
Disable *Enable
JP10
Buzzer enable/disable (CN16)
*Enable Disable
CN16
* default setting
11
14
14 2 2
11
1
1