Advantech B+B SmartWorx Wzzard BB-WSK-NRG-1 User guide

Wzzard™ Starter Kits
Energy Monitoring Bundle
Model BB-WSK-NRG-1
SET UP MANUAL

ENERGY MONITORING BUNDLE
2
Advantech B+B SmartWorx - Americas
707 Dayton Road
Ottawa, IL 61350 USA
Phone [phone]
Fax [phone]
Advantech B+B SmartWorx - European Headquarters
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone [phone]
Fax [phone]
www.advantech-bb.com
[e-mail]
Document Number: 710-11470-00_R4_BB-WSK-NRG-1_3517m

ENERGY MONITORING BUNDLE
3
CONTENTS
ENERGY MONITORING STARTER KIT ................................................................................................................4
WZZARD NETWORK SETUP..................................................................................................................................4
DOWNLOADING THE ENERGY mONITOR NODE RED FLOW TO THE GATEWAY...................................5
ACCESS Node-RED UI IN THE GATEWAY........................................................................................................10
NETWORK HEALTH PAGE....................................................................................................................................11
POWER UP WZZARD EDGE NODE ....................................................................................................................12
ATTACHING THE SENSORS ON THE INTELLIGENT EDGE NODES..........................................................13
ACCESSING THE DASHBOARD..........................................................................................................................14
SETTING UP AN E-MAIL ACCOUNT ...................................................................................................................15
SETTING UP YOUR DROPBOX FOR LOGGING...............................................................................................17
APPENDIX A. CARRIER TEXT MESSAGING URL ADDRESSES..................................................................19
Node-RED™ SOFTWARE LICENSE....................................................................................................................21
B+B SMARTWORX TECHNICAL SUPPORT......................................................................................................21

ENERGY MONITORING BUNDLE
4
ENERGY MONITORING STARTER KIT
Kit Model BB-WSK-NRG-1
The Wzzard™ Energy Monitoring Application makes it simple to see the real time and historical
electrical consumption of any individual machine or panel. Data can be exported to Dropbox for
further analysis. Email or text message alerts can be sent when user-configured high or low
limits are exceeded in critical applications.
Installation costs are kept low using the Wzzard wireless sensing platform. The platform creates
a self-forming, self-healing wireless mesh network that eliminates the need for wires and
requires no special skills to install. Each Wzzard sensor node is powered by long life batteries.
Using Node-RED™, a simple, browser based application preinstalled on the gateway, you can
monitor current draw from any web browser on your network.
The contents of the kit include:
Qty 1 WSD2MA3 3 analog-in units with M12 connector and external antenna
Qty 3 JC10F50-V 50A clamp on current sensor
Qty 1 WSCAM12-6 M12 cable
Qty 1 SG30000525-41 SmartSwarm 341™ Ethernet Gateway with Dust
WZZARD NETWORK SETUP
The Wzzard node and gateway in this kit are preconfigured. If this is the only Wzzard device in
your vicinity, it will need no further configuration. If other Wzzard gateways are nearby you will
need to change the network ID on both the gateway and the node. See respective node and
gateway manuals for instructions.

ENERGY MONITORING BUNDLE
5
DOWNLOADING THE ENERGY MONITOR NODE RED FLOW TO THE GATEWAY
Note: router must be in operational and online state in order to add the application (ie Eth1
must be plugged in).
1. Follow the instructions in the Gateway Quick Start guide to claim your gateway.
2. Select View Devices from the dropdown menu on the SmartWorx Hub Home Screen:
3. Select your device from the list of available devices:

ENERGY MONITORING BUNDLE
6
4. Select Add/Upgrade Apps:
5. Check the box next to Energy-Monitor.A list of components to be updated will appear.

ENERGY MONITORING BUNDLE
7
6. Click OK to accept the download.
7. Click Add/Upgrade Selected to start the download

ENERGY MONITORING BUNDLE
8
8. The download could take several minutes. To monitor the progress, select History from the
Manage Devices screen.

ENERGY MONITORING BUNDLE
9
9. As each component is updated, it will be marked with a check mark.
Note: “AddNode” commands will show an X if they have already been installed.

ENERGY MONITORING BUNDLE
10
ACCESS Node-RED UI IN THE GATEWAY
1. Attach the antenna to the Wzzard™ antenna port on the gateway.
2. Attach the Ethernet cable to the ETH0 port on the gateway and the other end to your PC.
You will use an Ethernet connection to configure the gateway and to communicate with it.
3. Attach the supplied power supply and plug it in.
4. Open a browser on your computer and open the Node-RED™ configuration page. The
default address is: 192.168.1.1:1880/ui. (Chrome or Firefox recommended.)
5. The Wzzard Node information values will populate when the node joins the network.
6. You can set up a phone number to receive text messages and/or an e-mail address for
receiving alerts on this page. For text messaging, you will need to select the cell carrier of
the receiving phone. If the carrier is not on the list, select custom, and add the URL of the
carrier to the phone number (ie: 1-123-[email protected]). See Appendix A for
carrier text addresses. If your carrier is not listed, contact your carrier for the address of their
SMS gateway.
7. You can enable or disable alerts as well as setting the trigger values on this page also.

ENERGY MONITORING BUNDLE
11
NETWORK HEALTH PAGE
1. Click the “Network Health” button on the lower left corner of the Configuration page. The
page below appears. This page shows the status of the network.

ENERGY MONITORING BUNDLE
12
POWER UP WZZARD EDGE NODE
1. Loosen the (4) black screws that hold the top of the node in place.
2. Install your batteries.
Note: Use (2) 3.6V 2400 mAH Lithium Thionyl Chloride AA batteries.
3. Install the battery clip.
4. Replace the cover. Tighten the (4) top screws to maintain IP67 rating. Torque each screw to 5
to 8 in-lb (0.6 to 0.9 Nm). This is equivalent to 1/4 to 1/2 turn after screw makes contact.
5. Check LED.
After you have installed the batteries, the LED will begin to blink. This indicates that the Node is
attempting to establish a network connection. The LED will cease blinking when a connection is
made.
6. Attach the External Antenna.
Note: The best way to remove the clip is to insert a
small flathead screwdriver between the batteries
and the clip, parallel to the batteries, and give the
screwdriver a gentle twist. This will remove the clip
without damage.
LED Indicator
Status
Data
Solid ON
Module startup initialization (approx. 10 seconds)
Slow Blink
(1 per second)
Attempting to establish connection with SmartMesh IP network.
Fast Blink
(10 per second)
Firmware update in progress.
OFF
Unit is connected to wireless network.

ENERGY MONITORING BUNDLE
13
ATTACHING THE SENSORS ON THE INTELLIGENT EDGE NODES
1. Wire Your Sensors.
You can connect up to three sensors to a Wzzard™ node.
Sensor
Wzzard Industrial Node with M12 cable
Wire Color
Sensor 1
Sensor (+) to M12 cable
BROWN
Sensor (-) to M12 cable
GREEN
Sensor 2
Sensor (+) to M12 cable
YELLOW
Sensor (-) to M12 cable
GRAY
Sensor 3
Sensor (+) to M12 cable
PINK
Sensor (-) to M12 cable
BLUE
•Open the wire protector clamp by pushing it away from the sensor body.
•Attach your wires.
•Close the wire protector clamp.
2. Mount Your Sensors.
The sensor can be mounted in any position.
Open the clamp release by pushing it away from the sensor body. Run the wire you are
monitoring through the opening in the sensor.
Close the sensor firmly around your wire and ensure that the clamp release has snapped back
into place.

ENERGY MONITORING BUNDLE
14
ACCESSING THE DASHBOARD
1. Open a browser on your computer and open the Node-RED™ configuration page. The
default address is: 192.168.1.1:1880/ui
2. Click on the “Dashboard” button on the lower left corner of the configuration page.
3. The dashboard should look like the screen below.
4. You can switch to the Configuration page or Network Health page by clicking on their
respective buttons on the upper left.

ENERGY MONITORING BUNDLE
15
SETTING UP AN E-MAIL ACCOUNT
1. From your browser, open the Node-RED™ flow at 192.168.1.1:1880.
2. Find the “Send Email” node, and double click on it.

ENERGY MONITORING BUNDLE
16
3. Enter your UserID and Password for your e-mail server in the appropriate boxes. (Leave
the “To” field blank.)
Note: If you are using a G-Mail account, you will need to enable “Less Secure
Apps” in the Google security settings. See below.
4. Click “Done”. Then Click the “Deploy” button in the upper right corner of the page.

ENERGY MONITORING BUNDLE
17
SETTING UP YOUR DROPBOX FOR LOGGING
1. Log in to your Dropbox account or sign up for a new one.
2. Once signed up or logged in:
•Go to https://www.dropbox.com/developers
•Click 'Create your app' box in the center of the screen.
•Select 'Dropbox API app'.
•Choose an appropriate answer as to whether your node should be limited to its own
folder or given full access. (TIP: This can be changed later, so choose 'Yes' to restrict
the application while testing might be a good idea.)
•Choose an app name.
•Click 'Create app'.
The subsequent app page will contain the App key, App secret and a 'Generate' button
to produce a suitable 'access token'. Save these strings so you can enter them into the
application later.
3. From your browser, open the Node-RED™ flow at 192.168.1.1:1880.
4. Locate “Log data to file”, then scroll right and locate the blue ‘Write Remote File’ node;
double click on it.

ENERGY MONITORING BUNDLE
18
5. Then click on the pencil icon next to the Dropbox text window.
6. Fill in the App Key, App Secret, and Access Token you got from Dropbox in their
respective fields. (See yellow box for more information.)
7. Click Updated; then Done again to close both windows.
8. Click the “Deploy” button in the upper right corner of the page.
9. Enable logging on the Dashboard web page.

ENERGY MONITORING BUNDLE
19
APPENDIX A. CARRIER TEXT MESSAGING URL ADDRESSES
U.S.A Carriers
Alltel
[10-digit phone number]@message.alltel.com
Example: [e-mail]
AT&T (formerly Cingular)
[10-digit phone number]@txt.att.net
[10-digit phone number]@cingularme.com
Example: [e-mail]
Boost Mobile
[10-digit phone number]@myboostmobile.com
Example: [e-mail]
Nextel (now Sprint Nextel)
[10-digit telephone number]@messaging.nextel.com
Example: [e-mail]
Sprint PCS (now Sprint Nextel)
[10-digit phone number]@messaging.sprintpcs.com
Example: [e-mail]
T-Mobile
[10-digit phone number]@tmomail.net
Example: [e-mail]
US Cellular
[10-digit phone number]email.uscc.net (SMS)
Example: [e-mail]
Verizon
[10-digit phone number]@vtext.com
Example: [e-mail]
Virgin Mobile USA
[10-digit phone number]@vmobl.com
Example: [e-mail]
International Carriers Email to SMS Gateway
7-11 Speakout (USA GSM)
[e-mail]
Airtel (Karnataka, India)
[e-mail]
Airtel Wireless (Montana, USA)
[e-mail]
Alaska Communications Systems
[e-mail]
Aql
[e-mail]
AT&T Enterprise Paging
[e-mail]
BigRedGiant Mobile Solutions
[e-mail]
Bell Mobility & Solo Mobile (Canada)
[e-mail]
BPL Mobile (Mumbai, India)
[e-mail]
Cellular One (Dobson)
[e-mail]
Cingular (Postpaid)
[e-mail]
Centennial Wireless
[e-mail]
Cingular (GoPhone prepaid)
[e-mail] (SMS)
Claro (Brasil)
[e-mail]
Claro (Nicaragua)
[e-mail]
Comcel
[e-mail]
Cricket
[e-mail] (SMS)
CTI
[e-mail]
Emtel (Mauritius)
[e-mail]
Fido (Canada)
[e-mail]
General Communications Inc.
[e-mail]

ENERGY MONITORING BUNDLE
20
Globalstar (satellite)
[e-mail]
Helio
[e-mail]
Illinois Valley Cellular
[e-mail]
Iridium (satellite)
[e-mail]
Iusacell
[e-mail]
i wireless
[e-mail]
Koodo Mobile (Canada)
[e-mail]
LMT (Latvia)
[e-mail]
Meteor (Ireland)
[e-mail]
Mero Mobile (Nepal)
[e-mail]
MetroPCS
[e-mail]
Movicom (Argentina)
[e-mail]
Mobitel (Sri Lanka)
[e-mail]
Movistar (Colombia)
[e-mail]
MTN (South Africa)
[e-mail]
MTS (Canada)
[e-mail]
Nextel (United States)
[e-mail]
Nextel (Argentina)
[e-mail]
Orange Polska (Poland)
[e-mail]
Personal (Argentina)
[e-mail]
Plus GSM (Poland)
[e-mail]
President’s Choice (Canada)
[e-mail]
Qwest
[e-mail]
Rogers (Canada)
[e-mail]
SL Interactive (Australia)
[e-mail]
Sasktel (Canada)
[e-mail]
Setar Mobile email (Aruba)
[e-mail]
Suncom
[e-mail]
T-Mobile (Austria)
[e-mail]
T-Mobile (UK)
[e-mail]
Telus Mobility (Canada)
[e-mail]
Thumb Cellular
[e-mail]
Tigo (Formerly Ola)
[e-mail]
Tracfone (prepaid)
[e-mail]
Unicel
[e-mail]
Virgin Mobile (Canada)
[e-mail]
Vodacom (South Africa)
[e-mail]
Vodafone (Italy)
[e-mail]
YCC
[e-mail]
MobiPCS (Hawaii only)
[e-mail]