Advantech UNO-127 User manual

User Manual
UNO-127
Intel® Atom™ Elkhart Lake
x6413E Compact Fanless Edge
Controller

UNO-127 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2022
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel®, Core™ and Atom™ are the trademarks of Intel Corporation
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Support
For more information on this and other Advantech products, please visit our websites
at: http://www.advantech.com
For technical support and service, please visit our support website at:
http://support.advantech.com/
*Model name UNO-127
UNO127
*Part number:
UNO-127-E22BA
UNO-127-E23BA
UNO127E22B2201-T, UNO127E22B2202-T, UNO127E22B2203-T,
UNO127E22B2204-T, UNO127E22B2205-T, UNO127E22B2206-T,
UNO127E22B2207-T, UNO127E22B2208-T, UNO127E22B2209-T,
UNO127E22B2210-T, UNO127E22B2211-T, UNO127E22B2212-T
UNO127E22B2301-T, UNO127E22B2302T, UNO127E22B2303-T
UNO127E22B2304-T, UNO127E22B2305-T, UNO127E22B2306-T
UNO127E22B2307-T, UNO127E22B2308-T, UNO127E22B2309-T
UNO127E22B2310-T, UNO127E22B2311-T, UNO127E22B2312-T
UNO127E22B2401-T, UNO127E22B2402-T, UNO127E22B2403-T
UNO127E22B2404-T, UNO127E22B2405-T, UNO127E22B2406-T
UNO127E22B2407-T, UNO127E22B2408-T, UNO127E22B2409-T
UNO127E22B2410-T, UNO127E22B2411-T, UNO127E22B2412-T
UNO127E22B2501-T, UNO127E22B2502-T, UNO127E22B2503-T
UNO127E22B2504-T, UNO127E22B2505-T, UNO127E22B2506-T
UNO127E22B2507-T, UNO127E22B2508-T, UNO127E22B2509-T
UNO127E22B2510-T, UNO127E22B2511-T, UNO127E22B2512-T
Part No. 2004012700 Edition 1
Printed in Taiwan June 2022

iii UNO-127 User Manual
UNO127E22B2101-T, UNO127E22B2102-T, UNO127E22B2103-T,
UNO127E22B2201-T, UNO127E22B2202-T, UNO127E22B2203-T,
UNO127E22B2204-T, UNO127E22B2205-T, UNO127E22B2206-T,
UNO127E22B2207-T, UNO127E22B2208-T, UNO127E22B2209-T,
UNO127E22B2210-T, UNO127E22B2211-T, UNO127E22B2212-T
UNO127E22B2301-T, UNO127E22B2302T, UNO127E22B2303-T
UNO127E22B2304-T, UNO127E22B2305-T, UNO127E22B2306-T
UNO127E22B2307-T, UNO127E22B2308-T, UNO127E22B2309-T
UNO127E22B2310-T, UNO127E22B2311-T, UNO127E22B2312-T
UNO127E22B2401-T, UNO127E22B2402-T, UNO127E22B2403-T
UNO127E22B2404-T, UNO127E22B2405-T, UNO127E22B2406-T
UNO127E22B2407-T, UNO127E22B2408-T, UNO127E22B2409-T
UNO127E22B2410-T, UNO127E22B2411-T, UNO127E22B2412-T
UNO127E22B2501-T, UNO127E22B2502-T, UNO127E22B2503-T
UNO127E22B2504-T, UNO127E22B2505-T, UNO127E22B2506-T
UNO127E22B2507-T, UNO127E22B2508-T, UNO127E22B2509-T
UNO127E22B2510-T, UNO127E22B2511-T, UNO127E22B2512-T
UNO127E23B2201-T, UNO127E23B2202-T, UNO127E23B2203-T,
UNO127E23B2204-T, UNO127E23B2205-T, UNO127E23B2206-T,
UNO127E23B2207-T, UNO127E23B2208-T, UNO127E23B2209-T,
UNO127E23B2210-T, UNO127E23B2211-T, UNO127E23B2212-T
UNO127E23B2301-T, UNO127E23B2302T, UNO127E23B2303-T
UNO127E23B2304-T, UNO127E23B2305-T, UNO127E23B2306-T
UNO127E23B2307-T, UNO127E23B2308-T, UNO127E23B2309-T
UNO127E23B2310-T, UNO127E23B2311-T, UNO127E23B2312-T
UNO127E23B2401-T, UNO127E23B2402-T, UNO127E23B2403-T
UNO127E23B2404-T, UNO127E23B2405-T, UNO127E23B2406-T
UNO127E23B2407-T, UNO127E23B2408-T, UNO127E23B2409-T
UNO127E23B2410-T, UNO127E23B2411-T, UNO127E23B2412-T
UNO127E23B2501-T, UNO127E23B2502-T, UNO127E23B2503-T
UNO127E23B2504-T, UNO127E23B2505-T, UNO127E23B2506-T
UNO127E23B2507-T, UNO127E23B2508-T, UNO127E23B2509-T
UNO127E23B2510-T, UNO127E23B2511-T, UNO127E23B2512-T

UNO-127 User Manual iv
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Please contact your local supplier for
ordering information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.

v UNO-127 User Manual
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference. In
this event, users are required to correct the interference at their own expense.
甲類資訊技術設備
甲類設備為其他符合甲類設備限制值之資訊技術設備，而非符合乙類資訊技術設備的
限制值；雖然不可限制此類設備之行銷，但使用場所必須被限制，不得進行居住的環
境中，且應於其機器本體及使用說明書中含有下列警語 :
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from the PC chassis
before manual handling. Do not touch any components on the CPU card or
other cards while the PC is powered on.
Disconnect the power before making any configuration changes. A sudden rush
of power after connecting a jumper or installing a card may damage sensitive
electronic components.

UNO-127 User Manual vi
Safety Instructions
1. Read these safety instructions carefully.
2. Retain this user manual for future reference.
3. Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
5. Protect the equipment from humidity.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
8. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
9. Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient overvoltage.
12. Never pour liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If any of the following occurs, have the equipment checked by service person-
nel:
–The power cord or plug is damaged.
–Liquid has penetrated the equipment.
–The equipment has been exposed to moisture.
–The equipment is malfunctioning, or does not operate according to the user
manual.
–The equipment has been dropped and damaged.
–The equipment shows obvious signs of breakage.
15. Do not leave the equipment in an environment with a storage temperature of
below -20 °C (-4 °F) or above 50 °C (122 °F) as this may damage the compo-
nents. The equipment should be kept in a controlled environment.
16. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only
with the same or equivalent type as recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
17. In accordance with IEC 704-1:1982 specifications, the sound pressure level at
the operator's position does not exceed 70 dB (A).
18. This product is intended to be supplied by an UL certified power supply or dc
source with SELV output, rated 10 Vdc, 4A minimum and Tmax 50 degree. If
you need further assistance, please contact Advantech for further information.
19. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet. The power outlet socket should have a grounded
connection.
20. For use in pollution free environments and indoor use.
21. This equipment is not suitable for use in locations where children are likely to be
present.
22. If the equipment is used in a manner not specified by the Advantech, the protec-
tion provided by the equipment may be impaired.

vii UNO-127 User Manual
23. The equipment contains no user-serviceable parts. Do not open, Return to man-
ufacturer for servicing.
24. Do not block air ventilation holes.
25. This is open type equipment and should be installed in a suitable enclosure.
DISCLAIMER: These instructions are provided according to IEC 704-1 standards.
Advantech disclaims all responsibility for the accuracy of any statements contained
herein.
Consignes de sécurité
1. Lire attentivement les instructions de sécurité.
2. Conserver ce manuel pour utilisation ultérieure,
3. Débranchez cet équipement de toute prise secteur avant le nettoyer. Utilisez
seulement un chiffon humide. N'utilisez pas de détergent liquide ou pulvérisé
pour le nettoyage.
4. Gardez cet équipement à l'abri de l'humidité.
5. Placez cet équipement sur une surface fiable pendant l'installation. Le faire ou
bien le laisser tomber peut causer des dégâts.
6. Les ouvertures sur l'enceinte servent à la convection de l'air. Protégez l'équipe-
ment contre surchauffe. NE COUVREZ PAS LES OUVERTURES.
7. Assurez-vous que la tension de la source d'alimentation est correcte avant de
connecter l'équipement à une prise de courant. La prise de courant doit avoir
une connexion à la terre.
8. Placez le câble d'alimentation de manière à ce que personne ne puisse marcher
dessus. Ne placez rien sur le câble d'alimentation.
9. Toutes les mises en garde et tous les avertissements sur l'équipement doivent
être notés.
10. Si l'équipement n'est pas utilisé pendant une longue période, débranchez-le de
la source d'alimentation pour éviter tout endommagement dû à une surtension
transitoire.
11. Ne jamais verser de liquide dans une ouverture. Cela pourrait provoquer un
incendie ou un choc électrique.
12. N'ouvrez jamais l'équipement. Pour des raisons de sécurité, l'équipement doit
être ouvert uniquement par du personnel qualifié.
13. Si l'une des situations suivantes se présente, faites vérifier l'équipement par le
personnel de service:
un liquide a pénétré dans l'équipment
L'équipement a été exposé à l'humidité.
L'équipement ne fonctionne pas bien, ou vous ne pouvez pas le faire fonction-
ner selon le manuel de l'utilisateur.
The equipment does not work well, or you cannot get it to work according to the
user's manual
L'équipement est tombé et endommagé
L'équipement présente des signes évidents de rupture.
14. NE LAISSEZ PAS CET ÉQUIPEMENT DANS UN ENVIRONNEMENT OU LA
TEMPÉRATURE DE STOCKAGE PEUT ÊTRE INFÉRIEURE À -20 ° C (-4 ° F)
OU BIEN SUPÉRIEURE À 50 ° C (122 ° F). CECI POURRAIT ENDOMMAGER
L'EQUIPEMENT. L'ÉQUIPEMENT DEVRAIT ÊTRE DANS UN ENVIRONNE-
MENT CONTRÔLÉ.
15. Ce produit est destiné à être alimenté par une source d'alimentation certifiée UL
ou par une source cc convenant à une utilisation à une température minimale
de 50 degrés Celsius, dont la sortie est conforme à la norme SELV et dont la

UNO-127 User Manual viii
puissance nominale est de 10 Vdc, 4 A, en cas de besoin. contactez Advant-
ech pour plus d'informations.
16. Pour une utilisation dans des environnements non polluant et à l'intérieur.
17. C'est appareil ne doit pas être utilisé dans des endroits où se trouvent des
enfants.
18. Si l'équipement est utilisé d'une manière non spécifiée par le fabricant, la pro-
tection fournie par l'équipement peut être altéré
19. L'équipement ne contient aucune pièce réparable par l'utilisateur. Ne pas ouvrir,
retourner au fabricant pour réparation.
20. Ne bloquez pas les ou es de ventilation.
21. Il s'agit d'un équipement de type ouvert et doit être installé dans un boîtier
approprié
ATTENTION: Danger d'explosion si la batterie est mal remplace. Remplacer unique-
ment par le meme type ou equivalent recommandé par le fabricant. Jeter les piles
usagées selon les instructions du fabricant.
安全指示
1. 請仔細閱讀此安全操作說明。
2. 請妥善保存此用戶手冊供日後參考。
3. 用濕抹布清洗設備前，請確認拔除電源線。請勿使用液體或去污噴霧劑清洗設備。
4. 對於使用電源線的設備，設備周圍必須有容易接觸到的電源插座。
5. 請勿在潮濕環境中試用設備。
6. 請在安裝前確保設備放置在可靠的平面上，意外摔落可能會導致設備損壞。
7. 設備機殼的開孔適用於空氣對，從而防止設備過熱。請勿覆蓋開孔。
8. 當您連接設備到電源插座前，請確認電源插座的電壓符合要求。
9. 請將電源線佈置在人們不易絆倒的位置，請勿在電源線上覆蓋任何雜物。
10. 請注意設備上所有的警告標示。
11. 如果長時間不使用設備，請拔除與電源插座的連結，避免設備被超標的電壓波動
損壞。
12. 請勿讓任何液體流入通風口，以免引起火灾或短路。
13. 請勿自行打開設備。為了確保您的安全，請透過經認證的工程師來打開設備。
14. 如遇下列情况，請由專業人員維修：
電源線或插頭損壞；
設備內部有液體流入；
設備曾暴露在過度潮濕環境中使用；
設備無法正常工作，或您無法透過用戶手冊來正常工作；
設備摔落或損壞；
設備有明顯外觀損；
15. 請勿將設備放置在超出建議溫度範圍的環境，即不要低於 -20°C （-4°F）或高
於 50°C （122°F），否則可能會造成設備損壞。
16. 注意：若電池更換不正確，將有爆炸危險。因此，只可以使用製造商推薦的同一
種或者同等型號的電池進行替換。請按照製造商的指示處理舊電池。
17. 根據 IEC 704‐1:1982 規定，操作員所在位置音量不可高於 70 分貝。
18. 限制區域：請勿將設備安裝於限制區域使用。
19. 免責聲明：請安全訓示符合 IEC 704‐1 要求。研華公司對其內容之準確性不承
擔任何法律責任。
20. 消费者若使用电源适配器供电，则应购买配套使用获得 CCC 认证并满足标准要求
的电源适配器。

ix UNO-127 User Manual
Contents
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Safety Precautions.................................................................................... 2
1.3 Packing List............................................................................................... 3
1.4 Hardware Specifications ........................................................................... 3
1.4.1 General ......................................................................................... 3
1.4.2 System Hardware ......................................................................... 3
1.4.3 I/O Interfaces ................................................................................ 3
1.4.4 Environment.................................................................................. 4
1.4.5 Certifications ................................................................................. 4
1.4.6 Extension Kit (Optional) ................................................................ 4
1.4.7 Dimensions ................................................................................... 5
Figure 1.1 UNO-127 Dimensions................................................. 5
Figure 1.2 UNO-127 Dimensions (With UNO-127-RS1EA Option-
al Extension kit) .......................................................... 5
Chapter 2 Hardware Functionality.......................7
2.1 Introduction ............................................................................................... 8
Figure 2.1 Diagram of Connector Locations on UNO-127 (Top
Side) ........................................................................... 8
Figure 2.2 Diagram of Key Components Location on UNO-127
(Bottom Side).............................................................. 8
Table 2.1: Key components, Connectors on Board..................... 9
2.2 External I/O Connector.............................................................................. 9
2.2.1 UNO-127 Base Unit ...................................................................... 9
Figure 2.3 Front Panel of UNO-127............................................. 9
Figure 2.4 Top View of UNO-127 ................................................ 9
2.2.2 Power Connector ........................................................................ 10
2.2.3 LAN: Ethernet Connector............................................................ 10
2.2.4 USB Connector........................................................................... 10
2.2.5 Display Connector....................................................................... 10
2.2.6 COM Connector.......................................................................... 10
Table 2.2: COM Connector Pin Assignments............................ 10
2.3 Internal I/O Connectors and Switches..................................................... 11
Figure 2.5 Internal I/O Connectors/Switches............................. 11
Table 2.3: Internal Connectors and Jumper Switches............... 11
2.3.1 M.2 Connector ............................................................................ 12
2.3.2 mPCIe Connector ....................................................................... 12
2.3.3 Nano SIM Slot............................................................................. 12
2.4 Others ..................................................................................................... 12
Figure 2.6 LED Indicators, Reset Buttons, and Antenna Hole... 12
2.4.1 LED Indicators ............................................................................ 12
2.4.2 Reset Buttons ............................................................................. 12
Chapter 3 Initial Setup ........................................13
3.1 Chassis Grounding.................................................................................. 14
Figure 3.1 Chassis Grounding Connection Diagram ................. 14
3.2 Connecting Power................................................................................... 14
3.3 Storage Installation (Optional)................................................................. 15
3.3.1 Installing mPCIE ......................................................................... 15
3.4 Mounting type: Din-rail ............................................................................ 17
3.5 Extension Kit Installation (Optional) ........................................................ 18

UNO-127 User Manual x
3.5.1 4 x COM & 1 x LAN extension kit (UNO-127-RS1EA)................ 18
3.6 BIOS Setting ........................................................................................... 20
Appendix A System Settings & Pin Defs ............. 21
A.1 Power Connector (DCIN1) ...................................................................... 22
Table A.1: Power connector pin assignments ........................... 22
A.2 LAN: Ethernet Connector (LAN1) ........................................................... 22
Table A.2: Ethernet Connector Pin Assignments ...................... 22
A.3 USB Connector (USB1) .......................................................................... 23
A.3.1 USB 3.0 Connector..................................................................... 23
Table A.3: USB 3.0 Connector Pin Assignments....................... 23
A.4 HDMI Connector (CN1)........................................................................... 24
Table A.4: HDMI Display Connector.......................................... 24
A.5 M.2 Connector ........................................................................................ 24
Table A.5: M.2 B Key Connector Pin Assignments ................... 24
A.6 mPCIe Connector (MINI1) ...................................................................... 26
Table A.6: mPCIe Connector Pin Assignments......................... 26
A.7 COM Port RS232/422/485 Settings........................................................ 27
A.7.1 COM1/COM2 RS232/422/485 Settings...................................... 27
A.7.2 COM3/COM4 RS232/422/485 Setting........................................ 27
A.7.3 COM Port RS422/485 Termination Resistor Setting .................. 30
A.8 AT/ATX Setting (PSON1)........................................................................ 30
A.9 Riser Connector ...................................................................................... 31
A.10 TPM 2.0 BIOS Setting............................................................................. 32
A.11 CPU Turbo Mode BIOS Setting .............................................................. 33

Chapter 1
1Overview
This chapter provides an overview
of UNO-127 specifications.
Sections include:
 Introduction
 Safety Precautions
 Accessories
 Hardware Specifications
 Dimensions

UNO-127 User Manual 2
1.1 Introduction
Advantech’s UNO-100 series are DIN-rail integrated controller that feature a modular
design for flexible configuration according to specific usage requirements.
UNO-127 is equipped with an Intel® Atom® 6413E processor, 4 or 8 GB DDR4 RAM,
and 64G eMMC storage, as well as 2 x LAN, 2 x USB and 1 x HDMI. It also supports
1 x full-size mini PCIe for convenient expansion to satisfy diverse industrial applica-
tions. Compliant with IEC 61010 certification requirements for industrial use, UNO-
127 can be equipped with an optional second-stack extension kit that supports addi-
tional 4 x COM ports, 1 x LAN port and 1 x M.2 B key for I/O and wireless connectivity
expansion.
1.2 Safety Precautions
Below are a few safety precautions for preventing injury when making connections. In
most cases, users can use a standard cable for connection.
Warning! Always disconnect the power cord from your chassis whenever you are
working on it. Do not connect while the power is on. A sudden rush of
power can damage sensitive electronic components. Only experienced
electronics personnel should open the chassis.
Warning! Toujours à la terre pour éliminer toute charge d'électricité statique avant
toucher UNO-127. Appareils électroniques modernes sont très sensi-
bles à charges d'électricité statique. Utilisez un bracelet antistatique à
tout moment. Placez tous composants électroniques sur une surface
antistatique ou dans un statique-sac blindé.
Caution! Always ground yourself to remove any static electric charge before
touching UNO-127. Modern electronic devices are very sensitive to
static electric charges. Use a grounding wrist strap at all times. Place all
electronic components on a static-dissipative surface or in a static-
shielded bag.
Caution! Toujours débrancher le cordon d'alimentation de votre boîtier lorsque
vous êtes travailler. Ne branchez pas lorsque l'appareil est allumé. Un
afflux soudain de puissance peut endommager les composants électro-
niques sensibles. Seulement connu personnel de l'électronique
devraient ouvrir le châssis.

3 UNO-127 User Manual
Chapter 1 Overview
1.3 Packing List
Please refer below for the packing list:
UNO-127 (with din-rail mount)
1 x 2 PIN Plug-in block for Power
1 x Earth-Ground cable
Quick Start Guide
Warranty card
If anything is missing or damaged, contact your distributor or sales representative
immediately.
1.4 Hardware Specifications
1.4.1 General
1.4.2 System Hardware
1.4.3 I/O Interfaces
Dimensions (W x D x H) 33.5 x 70 x 100 mm
Weight (Net) 0.5 kg
Mounting DIN-rail
Power Requirement 10 - 30VDC
Power Consumption 15.8W (typical), 35W (Max)
BIOS AMI EFI X64
Watchdog Timer Programmable 255 levels timer interval, from 1 to 255 sec
Hardware Security TPM 2.0
Processor Intel® Atom® Quad core x6413E, 1.5GHz
Memory 4 GB/8 GB DDR4 2666 MHz onboard
(Up to 32GB per Slot, Up to 64 GB totally)
Graphics Engine Intel® UHD Graphics
Ethernet 2 x i210-IT
LED Indicators LEDs for Power, RUN (Programmable),
LAN (Active, Status)
Storage Onboard 64GB eMMC (upgradeable up to 256GB by project)
Option mSATA shared with mPCIe slot
Expansion 1 x Full-size mPCIe slot (SATA/PCIe/USB2.0 signal)
LAN Ports 2 x RJ45, 10/100/1000 Mbps IEEE 802.3u 1000BASE-T Fast
Ethernet
Speed 2 x 10/100/1000BASE-T Fast Ethernet (RJ45)
USB Ports 2 x USB 3.2 Gen2
Displays 1 x HDMI (1920 x 1080 @60Hz)
Power Connector 1 x 2 Pin (terminal block)

UNO-127 User Manual 4
1.4.4 Environment
*Note: Operating Temperature to be -20 ~ 50 °C (-4 ~ 122 °F) without airflow.
1.4.5 Certifications
1.4.6 Extension Kit (Optional)
UNO-127 features a modularized design. Advantech offers an optional 2nd
extension kit.
UNO-127-RS1EA Extension unit
Operating Temperature* -20 ~ 60 °C (-4 ~ 140 °F) with 0.7m/s airflow
Storage Temperature - 40 ~ 85 °C (-40 ~ 185 °F)
Relative Humidity 10~95% RH @ 40 °C/104 °F, non-condensing
Shock Protection Operating, IEC 60068-2-27, 50G, half sine, 11ms
Vibration Protection Operating, IEC 60068-2-64, 2 Grms, random, 5 ~ 500 Hz, 1hr/axis
(mSATA)
Certification CE, FCC, CB, UL 61010-2-201, CCC, BSMI
Part number UNO-127-RS1EA
Description 2nd stack extension kit to support 1 x M.2 B key Interface
Ports 1 x M.2 B Key
Dimensions (W x D x H) 30 x 70 x 100 mm
Weight 0.145 kg

5 UNO-127 User Manual
Chapter 1 Overview
1.4.7 Dimensions
33.5 x 70 x 100 mm (W x D x H mm)
Figure 1.1 UNO-127 Dimensions
Figure 1.2 UNO-127 Dimensions (With UNO-127-RS1EA Optional Extension kit)

UNO-127 User Manual 6

Chapter 2
2Hardware
Functionality
This chapter shows how to setup
the UNO-127’s hardware func-
tions, including connecting
peripherals, setting switches and
indicators.
Sections include:
 Introduction
 External I/O Connector
 Internal I/O Connector
 LED Indicators
 Reset Buttons
 Antenna Hole

UNO-127 User Manual 8
2.1 Introduction
The following diagram demonstrates the location of UNO-127's motherboard's key
components and internal/external connectors.
Figure 2.1 Diagram of Connector Locations on UNO-127 (Top Side)
Figure 2.2 Diagram of Key Components Location on UNO-127 (Bottom Side)


DIMM3
DIMM1
CPU1


DIMM3
DIMM1
CPU1

9 UNO-127 User Manual
Chapter 2 Hardware Functionality
2.2 External I/O Connector
2.2.1 UNO-127 Base Unit
Figure 2.3 Front Panel of UNO-127
Figure 2.4 Top View of UNO-127
Table 2.1: Key components, Connectors on Board
Category Label Function
External
DCIN1 Power Connector
CN1 HDMI Connector
LAN1 LAN Connector x2
USB1 USB 3.2 x2 Connector
SW1 Reset Button + Power Button
PWR1 LED Indicator
Internal
CN2 Riser Connector
MINI1 MiniPCIe Connector
DIMM1 Memory Slot
DIMM2 Memory Slot
DIMM3 Memory Slot
DIMM4 Memory Slot
CPU CPU

UNO-127 User Manual 10
2.2.2 Power Connector
UNO-127 comes with a Phoenix connector that carries 10 - 30 VDC external power
input, and features reversed wiring protection. Therefore, the system will not accrue
damage from reversed polarity of ground lines and power lines. (Please refer to User
Manual - Appendix A.1 for pin assignments)
2.2.3 LAN: Ethernet Connector
UNO-127 is equipped with two 1 Gigabit LAN controllers. Intel i210 Ethernet control-
ler that complies with IEEE 802.3u 10/100/1000 Base-T is used as the controller
chip. The Ethernet port is a standard RJ-45 jack. Additionally, LED indicators are pro-
vided on the front of the device to indicate the system's Link (off/green/orange) and
Active (green) status. (Please refer to User Manual- Appendix A.2 for pin assign-
ments.)
2.2.4 USB Connector
UNO-127 features 2 x USB ports that comply with USB EHCI, 3 for Rev. 3.2 specifi-
cations. The USB connectors support plug-and-play and hot-swap- ping functionality
for external devices. Additionally, this can be enabled/disabled in the BIOS menu.
(Please refer to User Manual- Appendix A.3 for pin assignments.)
2.2.5 Display Connector
The UNO-127 provides 1 x HDMI connector for resolution interface 1920 x 1080 @
60Hz. (Please refer to User Manual- Appendix A.4 for pin assignments.)
2.2.6 COM Connector
UNO-127-RS1EA has 4 x COM RS232/422/485 ports of terminal block type. They
offer trans- mission speeds of 50 ~115.2 kbps. The default mode for both COM ports
(COM1&COM2) is RS-232 Mode. Settings can be adjusted via an on-board switch
(SW1). (Please refer to User Manual- Appendix A.8 for RS232/422/485 settings).
Table 2.2: COM Connector Pin Assignments
Pin COM1 Mode Signal Name Pin COM2 Mode Signal Name
1
RS232 CTS
2
RS232 CTS
RS422 T- RS422 T-
RS485 D- RS485 D-
3
RS232 RXD
4
RS232 RXD
RS422 T+ RS422 T+
RS485 D+ RS485 D+
5
RS232 TXD
6
RS232 TXD
RS422 R+ RS422 R+
RS485 RS485