Advantech UNO-2160 User manual

UNO-2160
Celeron-400 Universal Network
Controller with PC/104 extension
User Manual

UNO-2160 User Manual ii
Copyright
This document is copyrighted, © 2004. All rights are reserved. The origi-
nal manufacturer reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmit-
ted in any form or by any means without the prior written permission of
the original manufacturer. Information provided in this manual is
intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the
rights of third parties that may result from such use.
Acknowledgements
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft
Corp.
C&T is a trademark of Chips and Technologies, Inc.
All other product names or trademarks are properties of their respective
owners.
Support
For more information on this and other Advantech products, please visit
our websites at: http://www.advantech.com
For technical support and service, please visit our support website at:
http://www.advantech.com/support/
This manual is for UNO-2160.
Part No. 2002160000
1st Edition, Printed in Taiwan Jan. 2004

iii
Product Warranty
Advantech warrants to you, the original purchaser, that each of its prod-
ucts will be free from defects in materials and workmanship for one year
from the date of purchase.
This warranty does not apply to any products that have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech high quality-control standards and rigorous test-
ing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details. If you think you have
a defective product, follow these steps:
Step 1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any on-
screen messages you get when the problem occurs.
Step 2. Call your dealer and describe the problem. Please have your man-
ual, product, and any helpful information readily available.
Step 3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This
allows us to process your return more quickly.
Step 4. Carefully pack the defective product, a fully completed Repair
and Replacement Order Card and a photocopy proof of purchase
date (such as your sales receipt) in a shippable container. A prod-
uct returned without proof of the purchase date is not eligible for
warranty service.
Step 5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

UNO-2160 User Manual iv

v Table of Contents
Contents
Chapter 1 Overview ...........................................................2
1.1 Introduction ....................................................................... 2
1.2 Hardware Specifications ................................................... 3
1.3 Safety Precautions ............................................................. 4
1.4 Chassis Dimensions........................................................... 5
Figure 1.1:Chassis Dimensions....................................... 5
Chapter 2 Hardware Functionality ..................................8
2.1 Introduction ....................................................................... 8
Figure 2.1:Front panel of UNO-2160 ............................. 8
Figure 2.2:Rear panel of UNO-2160 .............................. 8
2.2 RS-232 Interface (COM1~COM2) ................................... 8
2.3 RS-232/422/485 Interface (COM3~COM4) ..................... 9
2.3.1 16C550 UARTs with 16-byte standard .......................... 9
2.3.2 RS-422/485 detection ..................................................... 9
2.3.3 Automatic Data Flow Control Function for RS-485 ...... 9
2.3.4 Termination Resistor (JP6) ............................................. 9
2.3.5 RS-232/422/485 Selection ............................................ 10
Figure 2.3:RS-422/485 jumper setting.......................... 10
Figure 2.4:RS-232 jumper setting................................. 10
2.3.6 RS-485 Auto Flow Control Mode and RS-422 Master/
Slave Mode Selection ...................................................... 11
Table 2.1:Auto Flow Control and RS-422 Slave/Master
Selection ........................................................... 11
2.3.7 IRQ and Address Setting .............................................. 12
Table 2.2:IRQ Setting via switch 1 at SW2.................. 12
Table 2.3:IRQ Setting via switch 1 at SW2.................. 12
2.4 LAN: Ethernet Connector .............................................. 13
2.5 Power Connector ............................................................. 13
2.6 PS/2 Keyboard and Mouse Connector ............................ 13
2.7 USB Connector ............................................................... 13
2.8 PCMCIA: PC Card Slot .................................................. 14
2.9 VGA Display Connector ................................................. 14
2.10 Battery Backup SRAM.................................................... 15
2.10.1 Lithium Battery Specification....................................... 15
Figure 2.5:The location of the lith. battery for SRAM . 15
2.11 Reset Button .................................................................... 15
Chapter 3 Initial Setup.....................................................18
3.1 Inserting a CompactFlash™ Card ................................... 18
3.2 Chassis Grounding .......................................................... 18

UNO-2160 User Manual vi
Figure 3.1:Chassis Grounding Connection................... 18
3.3 Connecting Power ........................................................... 19
3.4 Installing a Hard Disk ..................................................... 19
3.5 BIOS Setup and System Assignments ............................ 19
Appendix A System Settings and Pin Assignments ..........22
A.1 System I/O Address and Interrupt Assignment............ 22
Table A.1: UNO-2160 System I/O Ports ...................... 22
A.2 Board Connectors and Jumpers....................................... 24
Figure A.1:UNO-2160 conn. and jp. locations (fs) ...... 24
Figure A.2:UNO-2160 conn. and jp. locations (bs)...... 24
A.3 RS-232 Standard Serial Port (COM1~COM2) ............... 26
A.4 RS-232/422/485 Serial Port (COM3~COM4) ................ 27
A.5 Ethernet RJ-45 Connector (LAN1~LAN2)..................... 27
A.6 Phoenix Power Connector (PWR)................................... 28
A.7 PS/2 Keyboard and Mouse Connector ............................ 28
A.8 USB Connector (USB1~USB2) ...................................... 29
A.9 VGA Display Connector ................................................. 29
Appendix B Programming the Watchdog Timer .............32

2
CHAPTER
1
Overview
This chapter provides an overview of
UNO-2160’s specifications.
Sections include:
• Introduction
• Hardware specification
• Safety precautions
• Chassis dimensions

UNO-2160 User Manual 2
Chapter 1 Overview
1.1 Introduction
UNO-2160 is an embedded Application Ready Platform (ARP) that can
shorten your development time and offers rich networking interfaces to
fulfill extensive needs in different projects. Advantech’s Universal Net-
work Controller is designed to be a total solution for network enabled
Application Ready Platforms.
Leveraging field-approved and worldwide approved real-time OS tech-
nology, Advantech’s UNO-2000 series provides a Windows CE .NET
and Windows XP Embedded ready solution, and supports several stan-
dard networking interfaces, such as Ethernet, Wireless LAN, RS-232/
422/485 and so on. Because of its openness, great expansion capability
and reliable design (fanless and diskless), the UNO-2000 series are ideal
embedded platforms for implementing custom applications for diversi-
fied applications.

3 Chapter1
1.2 Hardware Specifications
• CPU: Celeron-400 MHz Ultra low-voltage version
• Memory: 256/512 MB SDRAM on board (Default: 256 MB SDRAM).
• Battery-backup RAM: 512 KB Battery-backup RAM
• VGA/Keyboard/Mouse: DB-15 VGA Connector, PS/2 keyboard and
mouse
• Serial Ports: 2 × RS-232 and 2 x RS-232/422/485 with DB-9 connec-
tors. Automatic RS-485 data flow control
• Serial Speeds: RS-232: 50~115.2 kbps, RS-422/485: 50~921.6 kbps
• LAN: Two 10/100 Base-T RJ-45 Ports
• USB interface: Two USB ports, USB UHCI, Rev. 1.1 compliant
• Printer port: One printer port
• PC Card: One PC Card slot. Supports CardBus (Card-32) Card and
16-bit (PCMCIA 2.1/JEIDA4.2) Card.
Supports +5 V, +3.3 V and +12 V @ 120 mA working power
• SSD: One internal Type I / Type II CompactFlash card slot
• LEDs: Power, IDE, Alarm for RAM Backup Battery
• PC/104: Two PC/104 Extension. (Optional)
• HDD: HDD extension kit for installation of one standard 2.5” HDD
• Anti-Shock: 20 G @ Wall mounting, IEC 68 2-27, half sine, 11 ms w/
HDD50 G @ Wall mounting, IEC 68 2-27, half sine, 11 ms w/CF
• Anti-Vibration: 2 Grms w/CF @IEC 68 section 2-64, random, 5 ~ 500
Hz, 1 Oct./min, 1 hr/axis.0.5 Grms w/ HDD @ IEC 68 section 2-64,
random, 5 ~ 500 Hz, 1 Oct./min, 1 hr/axis
• Power supply: 9 ~ 36 VDC
• Power consumption: Max. 35 W
• Operating temperature: -10~50°C (14~122° F)@ 5~85% relative
humidity.
• Relative humidity: 95% @ 40°C
• Weight: 1.6 kg
• Chassis size (W × L × H): 255 × 152 × 50 mm (10” × 6.0” × 2.0”)
• Software options: Windows® XP Embedded, Windows NT/2000/XP,
Windows CE .NET V4.2

UNO-2160 User Manual 4
1.3 Safety Precautions
The following sections tell how to make each connection. In most cases,
you will simply need to connect a standard cable.
Warning! Always disconnect the power cord from your
chassis whenever you are working on it. Do not
connect while the power is on. A sudden rush of
power can damage sensitive electronic compo-
nents. Only experienced electronics personnel
should open the chassis.
Caution! Always ground yourself to remove any static
electric charge before touching UNO-2160. Mod-
ern electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag.