Advantech PCM-4823/L Installation and operation manual

PCM-4823/L Startup Manual 1
Packing ListPacking List
Packing ListPacking List
Packing List
Before you begin installing your card, please make sure
that the following materials have been shipped:
• 1 PCM-4823/L all-in-one single board computer
• 1 startup manual
• 1 CD-ROM or disk for utilities, drivers, and manual
(in PDF format)
• 1 3.5" IDE flat cable
• 1 keyboard/mouse cable
• 1 secondary serial port cable (RS-232/422/485)
• 1 parallel cable
• 1 floppy cable
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Note: For detailed information on the PCM-4823/L,
please refer to the enclosed CD-ROM or disk
(in PDF format).
SpecificationsSpecifications
SpecificationsSpecifications
Specifications
Standard SBC Functions
•CPU: Embedded AMD DX5-133 (5 x 86-133) processor
•BIOS: AWARD 128 KB Flash memory
•Chipset:VIA VT82C496G
•System memory: One 72-pin SIMM socket, accepts
4/8/16/32 MB and supports FPM or EDO DRAM from 1
to 32 MB
PCM-4823/L
486 SBC with VGA/LCD/Ethernet
Startup Manual
PCM-4823 486 SBC with VGA/LCD/Ethernet
For more information on this and other Advantech products
please visit our website at:
http://www.advantech.com
http://www.advantech.com/epc
For technical support and service please visit our support
website at:
http://support.advantech.com
This manual is for the PCM-4823/L.
Part No.2006482302 1st edition
Printed in Taiwan Aug.1999
•Enhanced IDE hard disk drive interface:Supports up
to two IDE (VL-bus) hard disks.BIOS auto-detect and
PIO Mode 3 transfer protocol
•Serial ports: One serial RS-232 port, one serial
RS-232/422/485 port.Two 16550 serial UARTs
•Parallel port:One parallel port, supports SPP/EPP/
ECP mode
•Infrared port: Shared with COM2.Transfer rate up to
115 kbps
•Keyboard/mouse connector: Mini-DIN connector
supports a standard PC/AT keyboard and PS/2 mouse
•Power management: Supports power saving modes
including Normal/Standby/Suspend modes.APM 1.1
compliant
• Supports M-Systems' DiskOnChip®2000 Flash disk
up to 144 MB
• Watchdog timer: 1.6 second interval
Local-bus Flat Panel/VGA Interface (PCM-4823)
•Chipset: C&T 65550
•Display memory:1 MB DRAM
•Display type:Supports CRT and flat panel (EL, LCD
and gas plasma flat panel) displays. Can simultaneously
display CRT and flat panel
• CRT display mode: Non-interlaced CRT monitors,
resolutions up to 1280 x 1024 @ 16 colors
• Panel display modes: Supports resolutions up to
1024 x 768
Ethernet Interface
• Chipset: RTL 8019AS
• I/O address switchless setting
• Software compatible with NE1000 and NE2000
• Built-in boot ROM
Mechanical and Environmental
•Dimensions (L xW):145 mm x 102 mm (5.9" x 4.2")
•Power supply voltage:+5 V (4.75 V ~ 5.25 V)
•Power requirements: +5V @ 2 A (typical)
•Operating temperature: 0 ~ 60° C (32 ~ 140° F)
•Weight:0.65 kg (weight of total package)

2PCM-4823/L Startup Manual
Jumpers and ConnectorsJumpers and Connectors
Jumpers and ConnectorsJumpers and Connectors
Jumpers and Connectors
The PCM-4823/L has a number of jumpers that allow you to
configure your system to suit your application.
The table below lists the function of each of the board's
jumpers and connectors:
Jumpers
Label Function
J2 DOC®2000 address setting
J3 LCD power selector
J4 Clear CMOS
J6 COM2 selector
J8 Watchdog timer action
Connectors
Label Function
CN1 Power connector (-5 V, -12 V)
CN2 Floppy disk connector
CN3 PC/104 connector
CN4 Parallel port connector
CN5 PC/104 connector
CN6 Flat panel connector
CN7 Hard disk connector
CN8 IR connector (infrared)
CN9 COM2 connector
CN10 Ethernet connector
CN11 Power connector (+5 V, +12 V)
CN12 COM1 connector
CN13 PS/2 keyboard and PS/2 mouse
CN14 CRT display connector
J5 Reset switch
J7 CPU fan connector
Jumper Settings
J2: DOC®2000 address setting
Pins Address
1-2 3-4 5-6
closed closed closed C800 ~ C9FF
closed closed open CC00 ~ CDFF
*closed open closed D000 ~ D1FF
closed open open D400 ~ D5FF
open closed closed D800 ~ D9FF
open closed open DC00 ~ DDFF
open open closed E000 ~ E1FF
open open open OFF
J3: LCD power setting
Closed pins Voltage
1-2 3.3 V
*2-3 5 V
J4: Clear CMOS
Closed pins Result
1-2 Clear CMOS
*2-3 3 V Battery on
J6: COM2 selector
Closed pins Result
*1-2 RS-232
3-4 RS-422
5-6 RS-485
J8:Watchdog timer action
Closed pins Result
1-2 IRQ11
*2-3 System reset
* default setting

PCM-4823/L Startup Manual 3
Locating Jumpers
Locating Connectors
Mechanical DrawingMechanical Drawing
Mechanical DrawingMechanical Drawing
Mechanical Drawing
J3 J2
J6
J8
J4
J7
CN9
CN12
NET
LED
CN10
CN13
CN8
CN14
CN3CN5
SIMM1
CN1
CN2
CN4 CN7 CN6 CN11
J5
HDD
LED