Advantech PCM-4380F-M0A2E User manual

PCM-4380
Pentium® M 4" EPIC SBC with
MIO/VGA/LCD/LVDS Ethernet/
USB2.0 and SSD
User Manual

PCM-4380 User Manual ii
Copyright
This document is copyrighted, © 2007. All rights are reserved. The origi-
nal manufacturer reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmit-
ted in any form or by any means without the prior written permission of
the original manufacturer. Information provided in this manual is
intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the
rights of third parties that may result from such use.
Acknowledgements
Award is a trademark of Award Software International, Inc. VIA is a
trademark of VIA Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel, Pentium, Celeron, and MMX are registered trademarks of Intel Cor-
poration.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation. SMI is a
trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
All other product names or trademarks are properties of their respective
owners.
For more information on this and other Advantech products, please visit
our websites at: http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our support website at:
http://www.advantech.com/support
Part No. 2006438011 Edition 2
Printed in Taiwan November 2007

iii
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
Item Part Number
1 Startup manual
1 Utility CD
1 Mini jumper pack 9689000002
FLAT Cable 44P 20 cm 3Com & LPT 1.27 mm to D-sub
(CN30) 1700002034
FLAT Cable 44P IDC 44P/44P/40P keyed 50 cm
(CN27) 1701440504
Cable 20P/10P 10 cm EPIC ATX Power (CN1) 1700002055
Cable 6pin, 6-pin; 20 cm long: PS/2 KB & Mouse
(CN19) 1700060202
Cable 2*4P/10P EPIC AT POWER 15 cm (CN1) 1700003931
USB CABLE 20 Pin TO 2 Port L=30 cm PCM-43 series
(CN31) 1700004891
CABLE USB*2/10-2.0 mm 29 cm 1700001267
(PCM-4380U
series only)
Model Number Description
PCM-4380F-S4A2E Pentium M 1.4GHz(2M L2) w/Dual LAN/VGA/
LCD/CFC
PCM-4380F-S0A2E Celeron M 1.0GHz(512K L2) w/Dual LAN/VGA/
LCD/CFC
PCM-4380F-M0A2E Celeron M 600MHz(512K L2) w/Dual LAN/VGA/
LCD/CFC
PCM-4380Z2-S0A2E PCM-4380F-S0A2E with phoenix platinum pack-
age
PCM-4380Z2-S4A2E PCM-4380F-S4A2E with phoenix platinum pack-
age

PCM-4380 User Manual iv
Optional Accessories
Additional Information and Assistance
1. Visit the Advantech web site at www.advantech.com where you
can find the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's cus-
tomer service center for technical support if you need additional
assistance.
Please have the following information ready before you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, applica-
tion software, etc.)
• A complete description of the problem
• The exact wording of any error messages
PCM-410A-00A1E AC 97 Audio/USB module for PCM-4380/4386
series
PCM-410C-00A1E COM/LPT daughter board for EPIC

v
FCC
This device complies with the requirements in part 15 of the FCC rules:
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including inter-
ference that may cause undesired operation
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
device in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his/her
own expense. The user is advised that any equipment changes or modifi-
cations not expressly approved by the party responsible for compliance
would void the compliance to FCC regulations and therefore, the user's
authority to operate the equipment.
Caution! There is a danger of a new battery exploding if it
is incorrectly installed. Do not attempt to
recharge, force open, or heat the battery.
Replace the battery only with the same or equiv-
alent type recom- mended by the manufacturer.
Discard used batter- ies according to the manu-
facturer’s instructions.

PCM-4380 User Manual vi

vii
Contents
Chapter 1 General Information........................................2
1.1 Introduction....................................................................... 2
1.2 Specifications.................................................................... 2
1.2.1 Standard 4" Biscuit SBC Functions................................ 2
1.2.2 VGA/LVDS Interface..................................................... 3
1.2.3 Ethernet Interface............................................................ 3
1.2.4 Audio Function............................................................... 3
1.2.5 Mechanical and Environmental...................................... 4
1.3 Board layout and dimensions............................................ 5
Figure 1.1 Board layout: Dimensions (Component
Side) ....................................................... 5
Figure 1.2 Board layout: Dimensions (Solder Side)..5
Chapter 2 Installation........................................................8
2.1 Jumpers.............................................................................. 8
2.1.1 Jumper Location ............................................................. 8
Table 2.1 Jumpers..................................................... 8
2.1.2 Jumper Settings............................................................... 8
Table 2.2 At/ATX Power Select (J1)........................ 8
Table 2.3 LCD Power (J2)........................................ 8
Table 2.4 COM2 Setting (J3).................................... 9
Table 2.5 PCI-VIO Setting (J4)................................ 9
Table 2.6 CMOS clear (S2) ...................................... 9
2.2 Connectors....................................................................... 10
Table 2.7 Connectors.............................................. 10
2.3 Locating Connectors ....................................................... 11
Figure 2.1 Connectors (component side).................11
Figure 2.2 Connectors (solder side).........................11
2.4 Setting Jumpers............................................................... 12
2.5 Installing SO-DIMM....................................................... 13
2.6 IDE, CDROM hard drive connector (CN27)..................14
2.6.1 Connecting the hard drive............................................. 14
2.7 Solid State Disk............................................................... 14
2.7.1 CompactFlash (CN11).................................................. 14
2.8 Parallel port connector (CN30).......................................15
2.9 Keyboard and PS/2 mouse connector (CN19) ................ 15
2.10 Power & HDD LED Connector (CN13)......................... 15
2.10.1 Power & HDD LED Connector(CN13)........................ 15
2.10.2 Power Reset button (S1) ...............................................15
2.11 Power connectors (CN1)................................................. 16
2.11.1 Main power connector, +3.3V, +5 V, +12 V (CN1)..... 16

PCM-4380 User Manual viii
2.11.2 System FAN (CN5) ......................................................16
2.12 Audio interfaces (CN31)................................................. 16
2.12.1 Audio connector (CN31) .............................................. 16
2.13 COM port connector (CN21,CN30)................................ 16
2.13.1 COM2 RS-232/422/485 setting (J3).............................16
Table 2.8 J3: COM2 RS-232/422/485 select..........16
2.14 VGA/LCD/LVDS interface connections ........................ 17
2.14.1 CRT display connector (CN16).................................... 17
2.14.2 LVDS LCD panel connector (CN14) ...........................17
2.15 Ethernet configuration..................................................... 17
2.15.1 100Base-T/1000Base-T connector (CN8, CN9)........... 17
2.15.2 Network boot (Depends on Ethernet Controller Gigabit
Ethernet only) ............................................................... 17
2.16 Watchdog timer configuration ........................................ 17
2.17 USB connectors (CN31,CN18)....................................... 18
2.18 GPIO (General Purpose Input Output) (CN7)................. 18
Chapter 3 Chipset Software Installation Utility............20
3.1 Before you begin.............................................................20
3.2 Introduction..................................................................... 21
3.3 Installing the CSI Utility................................................. 21
Chapter 4 Award BIOS Setup.........................................26
4.1 Introduction..................................................................... 26
4.1.1 CMOS RAM Auto-backup and Restore....................... 26
4.2 Entering Setup................................................................. 27
Figure 4.1 Award BIOS Setup initial screen............27
4.3 Standard CMOS Setup.................................................... 28
Figure 4.2 Standard CMOS features screen............. 28
4.4 Advanced BIOS Features................................................ 29
Figure 4.3 Advanced BIOS features screen............. 29
4.4.1 Virus Warning............................................................... 29
4.4.2 L1 & L2 Cache ............................................................. 29
4.4.3 Quick Power On Self Test............................................ 30
4.4.4 First/Second/Third/Other Boot Device.........................30
4.4.5 Boot Up NumLock Status............................................. 30
4.4.6 Gate A20 Option........................................................... 30
4.4.7 Typematic Rate Setting................................................. 30
4.4.8 Typematic Rate (Chars/Sec)......................................... 30
4.4.9 Typematic Delay (msec)............................................... 30
4.4.10 Security Option.............................................................31
4.4.11 APIC Mode................................................................... 31
4.4.12 MPS Version Control For OS....................................... 31
4.5 Integrated Peripherals...................................................... 31
4.5.1 IDE Master/Slave PIO/UDMA Mode,.......................... 31

ix
4.5.2 On-Chip Secondary PCI IDE........................................ 32
Figure 4.4 Integrated peripherals .............................32
4.5.3 USB Controller ............................................................ 32
4.5.4 USB Keyboard/Mouse Support.................................... 32
4.5.5 AC97 Audio..................................................................32
4.5.6 Init Display First........................................................... 32
4.5.7 IDE HDD Block Mode ................................................. 33
4.5.8 Onboard Serial Port ...................................................... 33
4.5.9 Onboard Parallel Port.................................................... 33
4.5.10 Parallel Port Mode........................................................ 33
4.5.11 EPP Mode Select .......................................................... 33
4.5.12 ECP Mode Use DMA................................................... 33
4.6 Power Management Setup............................................... 34
Figure 4.5 Power management setup screen............ 34
4.6.1 Power-Supply Type ...................................................... 34
4.6.2 ACPI function...............................................................34
4.6.3 Power Management ...................................................... 35
4.6.4 Video Off In Suspend ................................................... 35
4.6.5 Modem Use IRQ........................................................... 35
4.6.6 HDD Power Down........................................................ 35
4.6.7 Soft-Off by PWR-BTTN .............................................. 35
4.6.8 PowerOn By LAN(GigaLAN option)........................... 36
4.6.9 PowerOn By Ring......................................................... 36
4.6.10 PowerOn By Alarm ...................................................... 36
4.6.11 Primary IDE 0 (1) and Secondary IDE 0 (1)................36
4.6.12 FDD, COM, LPT PORT............................................... 36
4.6.13 PCI PIRQ [A-D]# ......................................................... 36
4.7 PnP/PCI Configurations.................................................. 37
4.7.1 PnP OS Installed...........................................................37
Figure 4.6 PnP/PCI configurations screen...............37
4.7.2 Reset Configuration Data.............................................. 37
4.7.3 Resources controlled by:............................................... 37
4.7.4 PCI/VGA Palette Snoop ............................................... 37
4.8 Password Setting ............................................................. 38
4.9 Save & Exit Setup...........................................................38
4.10 Exit Without Saving........................................................ 38
Chapter 5 PCI SVGA/LCD Setup ..................................40
5.1 Introduction..................................................................... 40
5.1.1 CMOS setting for panel type ........................................ 40
5.1.2 Display type.................................................................. 40
5.1.3 Dual Independent Display ............................................ 40
5.2 Connections to Two Standard LCDs............................... 43
5.2.1 LG LM 150x06 (1024x768 LVDS LCD)..................... 43
Table 5.1 Connections to LCD/Flat Panel (CN1)... 43

PCM-4380 User Manual x
5.2.2 AU M170EG01 (1024x768 LVDS LCD @ 36bit)....... 44
Table 5.2 Connections to AU M170EG01 (CN1).. 44
5.3 Installation of the SVGA Driver ..................................... 45
5.3.1 Installation of Windows 2000.......................................45
5.4 Further Information......................................................... 48
Chapter 6 Audio Setup.....................................................50
6.1 Introduction..................................................................... 50
6.2 Driver installation............................................................ 50
6.2.1 Before you begin........................................................... 50
6.2.2 Windows 98 drivers......................................................51
Chapter 7 Ethernet Interface..........................................56
7.1 Introduction..................................................................... 56
7.2 Installation of Ethernet driver ......................................... 56
7.2.1 Installation for Windows 2000 ..................................... 56
7.3 Further information ......................................................... 62
Chapter 8 Installing MIO Modules ................................64
8.1 MIO Introduction ............................................................ 64
8.1.1 M2M concept................................................................ 64
8.1.2 Easy to have wireless technology with your embedded
motherboard..................................................................64
8.1.3 The best board combination for a system..................... 64
Figure 8.1 PCM-4380 + MIO 2320 ......................... 64
8.2 Optional Modules............................................................ 65
8.2.1 MIO-2310 Wireless module ......................................... 65
8.2.2 MIO-2320 GSM/GPRS module....................................65
8.3 MIO drawings ................................................................. 66
Figure 8.2 MIO module mounting diagram............. 66
Appendix A Pin Assignments .............................................68
A.1 Power connector (CN1)................................................... 68
Table A.1 ATX Power Connector (CN1)................ 68
A.2 Battery connector (CN4)................................................. 68
Table A.2 Battery Connector (CN4)........................ 68
A.3 System FAN (CN5)......................................................... 69
Table A.3 System FAN (CN5.................................. 69
A.4 Power Switch (CN6) ....................................................... 69
Table A.4 Power Switch (CN6)...............................69
A.5 GPIO (CN7) .................................................................... 70
Table A.5 GPIO (CN7)............................................ 70
A.6 LAN1(RJ45) (CN8)......................................................... 71
Table A.6 LAN1(RJ45+10/100 Transformer)
(CN8) ................................................... 71

xi
A.7 LAN2(RJ45) (CN9)......................................................... 72
Table A.7 LAN2(RJ45+10/100 Transformer)
(CN9) ................................................... 72
A.8 Compact II without Ejector (CN11)................................73
Table A.8 Compack II W/Ejector (CN11)............... 73
A.9 HD & Power LED (CN13)..............................................74
Table A.9 HD & Power LED (CN13)..................... 74
A.10 LVDS Connector (CN14)................................................ 75
Table A.10 LVDS Connector (CN14).......................75
A.11 Inverter Power (CN15)................................................... 76
Table A.11 Inverter Power (CN15)........................... 76
A.12 USB0/1 (CN18)............................................................... 77
Table A.12 USB0/1 (CN18)...................................... 77
A.13 Keyboard/Mouse (CN19)................................................ 78
Table A.13 KB_MS1 (CN19).................................... 78
A.14 COM1 (CN21)................................................................. 78
Table A.14 COM1 (CN21)........................................ 78
A.15 ISA_-5V (CN24)............................................................. 79
Table A.15 ISA_-5V (CN24) .................................... 79
A.16 RS-422/485 (CN26) ........................................................ 80
Table A.16 RS-422/485 (CN26)................................ 80
A.17 IDE0 (CN27)................................................................... 81
Table A.17 IDE0 (CN27) .......................................... 81
A.18 MIO-USB (CN28)........................................................... 82
Table A.18 MIO-USB (CN28).................................. 82
A.19 COM2/3/4 & LPT (CN30)..............................................83
Table A.19 COM2/3/4 & LPT (CN30) ..................... 83
A.20 USB2/3 & AC97 (Audio I/F) (CN31)............................. 85
Table A.20 USB2/3 & AC97 (AUDIO I/F) (CN31) . 85
Appendix B Mechanical Drawings.....................................88
B.1 Mechanical Drawings...................................................... 88
Figure B.1 PCM-4380 Mechanical Drawing (Compo-
nent Side) ............................................. 88
Figure B.2 PCM-4380 Mechanical Drawing (Solder
Side) ..................................................... 89
Appendix C DC Input Timing (Reference as ATX 2.2)...92
C.1 DC Input Timing............................................................. 92
Table C.1 DC Input Timing Table .......................... 92
Appendix D Cables..............................................................94
D.1 Cables table..................................................................... 94
Table D.1 Cables ..................................................... 94

PCM-4380 User Manual xii

1
CHAPTER
General Information
This chapter gives background infor-
mation on the PCM-4380.

PCM-4380 User Manual 2
Chapter 1 General Information
1.1 Introduction
The PCM-4380 is an EPIC SBC (Single Board Computer) with a high
performance and lower power based on Pentium M/Celeron M proces-
sors. The PCM-4380, in conjunction with Intel 855GME chipset, sup-
ports processors clocked at up to 1.4 GHz, four USB 2.0 compatible
ports, up to 2 PCI Fast or Gigabit Ethernet interface, 2 Channel LVDS
interface and can accommodate up to 1 GB of DDR RAM memory.
SpeedStep (EIST) technology is another important features for PCM-
4380 which can save energy and ensure longer battery life, since it allows
the operating system to reduce the processor clock speed when less work
is being done.
1.2 Specifications
1.2.1 Standard 4" Biscuit SBC Functions
•CPU: Embedded Pentium M Processor supported at Front Side Bus
(FSB) 400MHz
•System Memory: 1x SODIMM socket, support ECC Double Data
Rate (DDR) 128 MB to 1GB, accept 128/256/512/1000 MB
DDR200/266/333 DRAM
•2nd Cache Memory: Depend on CPU type from 512 KB to 2 MB
•System Chipset: Intel 855GME GMCH/ICH4 chipset
•BIOS: AWARD 4 Mbit Flash BIOS
•Watchdog timer: 255 levels timer interval
•Expansion Interface: MIO interface, integrated PCI2.0, USB2.0,
SMBus, AC97
•Battery: Lithium 3 V/196 mAH
•Power management: Supports power saving modes including
Normal/Standby/Suspend modes. APM 1.2, ACPI compliant
•Enhanced IDE interface: One channels supports up to 2 EIDE
devices. BIOS auto-detect, PIO Mode 3 or Mode 4, supports
UDMA 33 mode
•Serial ports: 4 serial RS-232 ports, COM1/3/4: RS-232, COM2:
RS-232/422/485
•Parallel port: One parallel port, supports SPP/EPP/ECP mode

3 Chapter1
•Keyboard/mouse connector: Supports one standard PC/AT key-
board and a PS/2 mouse
•Audio: Support AC 97 Audio Interface (with PCM-410A-00A1E
option)
•USB: 4 USB 2.0 compliant universal serial bus ports
•Solid State Disk (SSD): Supports one 50-pin socket for CFC type
I/II (PCM-4380F series only)
1.2.2 VGA/LVDS Interface
•Chipset: Intel 855GME Graphic Memory Control Hub (GMCH)
•Memory Size: Optimized Shared Memory Architecture, support
64MB frame buffer using system memory
•Resolution: CRT display Mode: pixel resolution up to 1600 x 1200
@ 85 Hz and 2048 x 536 @ 75 Hz
•LVDS Interface: up to UXGA panel resolution with frequency
range from 25MHz to 112MHz
•Dual Independent Display: supports CRT+LVDS
•LVDS: support 2 channel 36-bits LVDS LCD Panel
1.2.3 Ethernet Interface
•Chipset supports:
– 10/100 Mbps: Intel 82551ER
– 10/100/1000 Mbps: Intel 82541PI (optional)
•Interface: 2 x RJ45, Standard IEEE 802.3u (100Base-T)
1.2.4 Audio Function
•Chipset: Intel 82801DB I/O Controller Hub 4 (ICH4) AC97 inter-
face
•Audio controller: Support AC97 3D Audio by PCM-410A-00A1E

PCM-4380 User Manual 4
1.2.5 Mechanical and Environmental
• Dimensions: 115 x 165 mm (4.5" x 6.5") Mechanical Drawing (dxf
file) is available.
• Power Supply Type: ATX, AT
• Power Requirement:
–ATX:
+5 V ±5%, ±12 V ±5% (optional)
–AT:
5 V only to boot up, 12 V for LCD inverter and PC/104 module
(12 V optional for PC104 add on card and LCD inverter)
• Power Consumption: (Pentium M 1.4 GHz with 256 MB DDR333)
– Max: 2.38 A @ 5 V, 0.08 A @ 12 V, 1.82 A @ 3.3 V
– Typical: 1.82 A @ 5 V, 0.08 A @ 12 V, 1.23 A @ 3.3 V
• Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Operating Humidity: 0% ~ 90% relative humidity, noncondensing
• Storage Temperature:
– Standard products (0 ~ 60° C)
– Storage temperature: -20 ~ 70° C
• Storage Humidity:
– Standard products (0 ~ 60° C)
– Relative humidity: 95% @ 60° C
• Weight: 0.85 kg (reference weight of total package)

5 Chapter1
1.3 Board layout and dimensions
Figure 1.1: Board layout: Dimensions (Component Side)
Figure 1.2: Board layout: Dimensions (Solder Side)

PCM-4380 User Manual 6

2
CHAPTER
Installation
This chapter explains the setup proce-
dures of the PCM-4380 hardware,
including instructions on setting jump-
ers and connecting peripherals,
switches and indicators. Be sure to
read all safety precautions before you
begin the installation procedure.
Sections include:

PCM-4380 User Manual 8
Chapter 2 Installation
2.1 Jumpers
The PCM-4380 has a number of jumpers that allow you to configure your
system to suit your application. The table below lists the functions of the
various jumpers.
2.1.1 Jumper Location
2.1.2 Jumper Settings
Note: In ATX mode, please use ATX power cable (PN: 1700002055:
20P/10P EPIC ATX POWER Cable 10CM) in the bundle package
to connect the power supply.
In AT mode, please use AT power cable (PN :1700003931: 2*4P/
10P EPIC AT POWER 15 cm) in the bundle package to connect
the power supply.
There are two 4 pin connectors on the AT power cable.
It's ok to connect single big 4P under AT mode.
The maximum current for (5 V, 12 V) through this “single big 4P”.
Table 2.1: Jumpers
Label Function
J1 AT/ATX Power Select
J2 LCD Power
J3 COM2 Setting
J4 PCI VIO Setting
Table 2.2: At/ATX Power Select (J1)
Setting Function
1-2 AT Power Mode
None ATX Power Mode
Table 2.3: LCD Power (J2)
Setting Function
1-2 +5 V
2-3 +3.3 V