Advantech PPC-153 User manual

PPC-153
Pentium® III processor-based
panel PC with 15" LCD flat panel
display
User’s Manual

Copyright notice
This document is copyrighted 2001, by Advantech Co., Ltd. All rights
are reserved. Advantech Co., Ltd. reserves the right to alter the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of Advantech. Information provided in this manual is
intended to be accurate and reliable. However, Advantech assumes no
responsibility for use of this manual, nor for any infringements upon
the rights of third parties which may result from such use.
All brand and product names mentioned herein are trademarks or
registered trademarks of their respective holders.
Part No. 2008015310
2nd Edition Printed in Taiwan May 2001

FCC Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses and can radiate radio
frequency energy. If not installed and used in accordance with this
user's manual, it may cause harmful interference to radio communica-
tions. Note that even when this equipment is installed and used in
accordance with this user's manual, there is still no guarantee that
interference will not occur. If this equipment is believed to be causing
harmful interference to radio or television reception, this can be
determined by turning the equipment on and off. If interference is
occurring, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to a power outlet on a circuit different from
that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Warning: Any changes or modifications made to the equipment
which are not expressly approved by the relevant
standards authority could void your authority to
operate the equipment.

Packing List
Before installing your panel PC, ensure that the following materials
have been received:
• PPC-153 series panel PC
• User's manual
• Accessories for PPC-153
- Y-shaped adapter for PS/2 mouse and keyboard
- Power cord (1.8 m) - USA type (other types are available on
request)
- Floppy disk with CD-ROM drive driver
- "Drivers and Utilities" CD-ROM disc
- Mounting kits and packet of screws
- Heat sink (optional) (refer to Notes 1 and 2 below)
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
Note 1: If the unit you have bought is basic (i.e. without a
CPU, HDD, or SDRAM), you will find this optional
item in the accessory box.
Note 2: If you install an Intel
®
processor yourself, you must
install a heat sink above the CPU. This will avoid
heat damage to the CPU.

Additional Information and Assistance
1. Visit the Advantech websites at www.advantech.com or
www.advantech.com.tw where you can find the latest information
about the product.
2. Contact your distributor, sales representative, or Advantech's
customer service center for technical support if you need additional
assistance. Please have the following information ready before you
call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version,
application software, etc.)
• A complete description of the problem
• The exact wording of any error messages
Warning! 1. Input voltage rated 100-250 V
AC
, 50/60 Hz, 3 A
2. Use a 3 V @ 195 mA lithium battery
3. Packing: please carry the unit with both hands,
handle with care
4. Our European representative:
Advantech Europe GmbH
Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel:[phone]
Fax:[phone]
5. Maintenance: to properly maintain and clean the
surfaces, use only approved products or clean with a
dry applicator

Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened
only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to
the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRON-
MENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F)
OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT.
The sound pressure level at the operator's position according to IEC 704-1:1982 is no
more than 70dB(A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine
Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur
Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich
sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-
zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es
sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in
das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und
von einer qualifizierten Servicestelle zu überprüfen:
a - Netzkabel oder Netzstecker sind beschädigt.
b - Flüssigkeit ist in das Gerät eingedrungen.
c - Das Gerät war Feuchtigkeit ausgesetzt.
d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioni ert
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. Bitte lassen Sie das Gerät nicht unbehehrt hinten unter -20° C (-4° F) oder oben
60° C (140° F), weil diesen Temperaturen das Gerät zerstören könten.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70
dB(A) oder weiger.
DISCLAIMER: This set of instructions is given according to IEC704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

Contents
CHAPTER 1 General Information 1
1.1 Introduction .................................................................. 2
1.2 How to Use This Manual .............................................. 4
1.3 Specifications ............................................................. 6
General ....................................................................................6
Standard PC functions .............................................................6
Flat panel interface...................................................................7
Audio function ..........................................................................7
PCI bus Ethernet interface .......................................................8
PCMCIA interface .................................................................... 8
Touchscreen (optional) .............................................................9
Optional modules .....................................................................9
Environment ........................................................................... 10
1.4 Dimensions ............................................................... 11
CHAPTER 2 System Setup 13
2.1 A Quick Tour of the Panel PC .................................... 14
2.2 Preparing For First-time Use ..................................... 17
2.3 Installation Procedures .............................................. 17
2.3.1 Connecting the power cord ............................................ 17
2.3.2 Installing the DC power insulator with hood.................... 18
2.3.3 Connecting the keyboard and mouse ............................ 21
2.3.4 Switching on the power ................................................. 21
2.4 Running the BIOS Setup Program ............................. 22
2.5 Installing System Software ......................................... 23
2.6 Installing the Drivers .................................................. 24
CHAPTER 3 Using the Panel PC 27
3.1 Introduction ................................................................ 28
3.2 Floppy Drive.............................................................. 28

3.3 CD-ROM Drive.......................................................... 29
3.4 PCMCIA ................................................................... 30
3.5 PS/2 Mouse and Keyboard ....................................... 33
3.6 PCI/ISA Bus Expansion ............................................. 33
3.7 Parallel Port .............................................................. 35
3.8 Serial COM Ports ...................................................... 35
3.9 VGA Port .................................................................. 36
3.10 Game Port .............................................................. 36
3.11 USB Ports ............................................................... 36
3.12 Audio Interface ........................................................ 37
3.13 Ethernet .................................................................. 37
3.14 Adjusting the LCD Contrast and Brightness ............. 37
3.15 Touchscreen (Optional) ............................................ 38
CHAPTER 4 Hardware Installation and Upgrading 39
4.1 Overview of Hardware Installation and Upgrading ...... 40
4.2 Disassembling the Panel PC..................................... 40
4.3 Installing the 2.5" Hard Disk Drive (HDD)................... 42
4.4 Installing the Central Processing Unit (CPU) .............. 43
4.5 Installing the SDRAM Memory Module ....................... 46
4.6 Installing the Floppy Disk Drive (FDD) and
Slim CD-ROM Drive................................................ 47
CHAPTER 5 Jumper Settings and Connectors 49
5.1 Jumpers and Connectors .......................................... 50
5.1.1 Setting jumpers ............................................................. 50
5.1.2 Jumpers and switch ...................................................... 51
5.1.3 Locating jumpers and switch ......................................... 52
5.1.4 Connectors ................................................................... 53
5.1.5 Locating connectors .................................................... 544
5.2 CPU Installation ......................................................... 55
5.3 CMOS Clear for External RTC (JP8) ......................... 55

5.4 COM-port Interface .................................................... 56
5.4.1 COM2 RS-232/422/485 setting (JP3, JP4, JP5)............. 56
5.4.2 COM1 / COM2 pin 9 output type setting (JP9) .............. 57
5.4.3 COM3 / COM4 pin 9 output type setting (JP6) .............. 58
5.5 Internal -12 V Source Selection Setting (JP1) ............ 58
5.6 VGA Interface............................................................ 59
5.6.1 LCD panel power setting ............................................... 59
5.6.2 Panel type select (SW3) ............................................... 59
5.7 Watchdog Timer Configuration .................................. 60
5.7.1 Watchdog activity selection (JP7) ................................. 60
CHAPTER 6 PCI Bus Ethernet Interface 61
6.1 Introduction ................................................................ 62
6.2 Installation of Ethernet Driver ..................................... 62
6.2.1 Installation for Windows 95............................................ 63
6.2.2 Installation for Windows 98............................................ 65
6.2.3 Installation for Windows NT ........................................... 68
6.2.4 Installation for Windows 2000/ME ................................. 70
6.3 Further Information .................................................... 70
CHAPTER 7 AGP SVGA Setup 71
7.1 Introduction ................................................................ 72
7.1.1 Chipset ......................................................................... 72
7.1.2 Display memory ............................................................ 72
7.1.3 Display types ................................................................ 72
7.2 Installation of SVGA Driver ........................................ 73
7.2.1 Installation for Windows 95/98 ....................................... 74
7.2.2 Installation for Windows NT ........................................... 75
7.2.3 Installation for Windows 2000 ........................................ 76
7.2.4 Installation for Windows ME .......................................... 77
7.3 Further Information .................................................... 78
CHAPTER 8 Audio 79
8.1 Introduction ................................................................ 80
8.2 Installation of Audio Driver ......................................... 80