Aeronaut Airmarine Special User manual

aero
naut
Airmarine Special
Order-No. 3042/00

0
0
1
23
4
5
6
7
8
9
10
11
11
11
In 1958, Jo Michelini won the „APBA Class F“ title with the Airmarine Special. As an experienced designer he created a unique hull for his
hydroplane that proved to run very stable and reliable at speeds in excess of 110 km/h.
We developed a model of the Airmarine Special in 1:5,2 scale, which has not only the looks but also the characteristics of the original. The
hydroplane kit is made of mahogny and birch ply, cockpit and fin are covered with Oratex. A special jig, which is typical for all laser cut aero-naut
models, is used to build the hull and ensures a rapid and easy building process.
Like the original, the model of the Airmarine Special is powered by an outboard motor, which is availbable from aero-naut.
Construction should be according to the step-by-step instructions provided in this manual. Remove only those parts from the laser cut sheets which
are required for the current building step.
Use a sharp modelling knife to cut individual parts from laser sheets. Use sandpaper to clean any residue of the laser cutting process from the
individual parts to get good contact surfaces for gluing. Always check that parts fit perfectly. Correct, if necessary, before you glue. Give glue
sufficient time to dry before you begin with the next step.
We recommend white glue and epoxy resin (if not otherwise noted) for gluing, which offer good strength and low weight. Both types of glue retain
a certain degree of elasticity even after the glue has cured und will stand up to any loads which occur during handling and operating the boat.
Be careful when handling untreated wood, especially mahogany. To avoid specks of glue, which might damage the surface of the wood, treat all
parts with wood filler (aero-naut Order-No. 7666/02) and sand with 320 grade paper before you glue. Also, before you race the boat on your local
lake or river, make sure you waterproof the model with several coats of a good clear varnish (inside and outside). Use epoxy resin for all parts that
you glue to a varnished surface.
Recommended Equipment
ŸOutboard motor Aqua Race 60* Order-No. 7005/01
or
ŸRetro-outboard motor Order-No. 7005/05
Ÿ2-blade race prop Ø 29-31 mm
Ÿ2 x 2.300 mAh2- to 3-cell LiPo ,
* Motor not included. Suitable for 28 mm outrunners with 3,17 mm shaft.
Airmarine Special Fit together both parts of the aero-naut jig and secure on
building board with tape.
Glue together two parts 11 to form the keel. Insert formers into jig
as shown, insert keel into formers and jig and glue keel to formers.
Secure parts in this and in following bulding steps with
pegs, clamps or tape until glue has dried.
1
2
We recommend our aero-pick modeller´s pins
for building.
Order-No. 7855/02
Tip

0
0
1
23
4
5
6
7
8
9
10
11
11
11
In 1958, Jo Michelini won the „APBA Class F“ title with the Airmarine Special. As an experienced designer he created a unique hull for his
hydroplane that proved to run very stable and reliable at speeds in excess of 110 km/h.
We developed a model of the Airmarine Special in 1:5,2 scale, which has not only the looks but also the characteristics of the original. The
hydroplane kit is made of mahogny and birch ply, cockpit and fin are covered with Oratex. A special jig, which is typical for all laser cut aero-naut
models, is used to build the hull and ensures a rapid and easy building process.
Like the original, the model of the Airmarine Special is powered by an outboard motor, which is availbable from aero-naut.
Construction should be according to the step-by-step instructions provided in this manual. Remove only those parts from the laser cut sheets which
are required for the current building step.
Use a sharp modelling knife to cut individual parts from laser sheets. Use sandpaper to clean any residue of the laser cutting process from the
individual parts to get good contact surfaces for gluing. Always check that parts fit perfectly. Correct, if necessary, before you glue. Give glue
sufficient time to dry before you begin with the next step.
We recommend white glue and epoxy resin (if not otherwise noted) for gluing, which offer good strength and low weight. Both types of glue retain
a certain degree of elasticity even after the glue has cured und will stand up to any loads which occur during handling and operating the boat.
Be careful when handling untreated wood, especially mahogany. To avoid specks of glue, which might damage the surface of the wood, treat all
parts with wood filler (aero-naut Order-No. 7666/02) and sand with 320 grade paper before you glue. Also, before you race the boat on your local
lake or river, make sure you waterproof the model with several coats of a good clear varnish (inside and outside). Use epoxy resin for all parts that
you glue to a varnished surface.
Recommended Equipment
ŸOutboard motor Aqua Race 60* Order-No. 7005/01
or
ŸRetro-outboard motor Order-No. 7005/05
Ÿ2-blade race prop Ø 29-31 mm
Ÿ2 x 2.300 mAh2- to 3-cell LiPo ,
* Motor not included. Suitable for 28 mm outrunners with 3,17 mm shaft.
Airmarine Special Fit together both parts of the aero-naut jig and secure on
building board with tape.
Glue together two parts 11 to form the keel. Insert formers into jig
as shown, insert keel into formers and jig and glue keel to formers.
Secure parts in this and in following bulding steps with
pegs, clamps or tape until glue has dried.
1
2
We recommend our aero-pick modeller´s pins
for building.
Order-No. 7855/02
Tip

18
17
16
17
16
16
17
12
12
12
13
13
14
14
14
15
15
15
Insert the two stringers 12 in formers and jig
and glue stringers to formers.
Glue in place bow plate 13 together
with stringers 14. Then glue stringers
15 in place.
3
4
Insert stringers 16 + 17 into notches on the underside of
sponsons and glue.
Carefully sand the contact surfaces of keel and formers with a sanding block and glue in
place part 18. Secure and weigh down evenly until glue has dried. Make sure that the front
section of the bottom (light brown) is in good contact with keel and formers while the tabs
of the formers remain in firm contact with the building board underneath the jig, so that the
front section of part 18 is slightly rounded.
5
6

18
17
16
17
16
16
17
12
12
12
13
13
14
14
14
15
15
15
Insert the two stringers 12 in formers and jig
and glue stringers to formers.
Glue in place bow plate 13 together
with stringers 14. Then glue stringers
15 in place.
3
4
Insert stringers 16 + 17 into notches on the underside of
sponsons and glue.
Carefully sand the contact surfaces of keel and formers with a sanding block and glue in
place part 18. Secure and weigh down evenly until glue has dried. Make sure that the front
section of the bottom (light brown) is in good contact with keel and formers while the tabs
of the formers remain in firm contact with the building board underneath the jig, so that the
front section of part 18 is slightly rounded.
5
6

20
20
21
21
21
19
19
19
22
22
22
Glue parts 19 to the underside of the sponsons. Make sure that parts 19 are flush with stringers 16 along the inner edge of the sponsons. Carefully
fit parts 22, then glue in place.
Slightly bevel the contact surfaces of parts 20 + 21 for a proper fit, then glue in place to complete the sponsons. Leave to dry.
7
8
75
76
77
77
23
23
23
Remove hull from jig and cut off building tabs with a razor saw as indicated.
Assemble the boatstand from parts 75, 76 + 77,
and glue together.
Insert parts 23 into hull and glue in place.
9
10
11

20
20
21
21
21
19
19
19
22
22
22
Glue parts 19 to the underside of the sponsons. Make sure that parts 19 are flush with stringers 16 along the inner edge of the sponsons. Carefully
fit parts 22, then glue in place.
Slightly bevel the contact surfaces of parts 20 + 21 for a proper fit, then glue in place to complete the sponsons. Leave to dry.
7
8
75
76
77
77
23
23
23
Remove hull from jig and cut off building tabs with a razor saw as indicated.
Assemble the boatstand from parts 75, 76 + 77,
and glue together.
Insert parts 23 into hull and glue in place.
9
10
11

25
25
25
26
26
27
27
23
23
24
24
Fit stringers 24 to formers along the outside of parts 23 and glue in place. Make sure that stringers are fully seated in notches of formers.
Now is a good time to treat the inside of the hull with wood filler or diluted epoxy resin to protect the wood against moisture.
12
Glue reinforcement 26 and steel plate 27 to frame 25.
Then glue frame 25 to front of parts 23.
Note: Reinforcement and steel plate face down!
13
28
28
28
23
19
20.1
20.1
20.1
30
23
29
30
Flush witht the upper edge glue mahogany panels 28 to the outside of parts 23. Make sure there is a gap of approximately 1.5
to 2 mm between stringer 19 and the lower edge of part 28. Remove any residual glue from the gap.
Insert deck parts 29 + 30 into the gap beneath the side panels 28 and secure temporarily with tape or clamps. Apply tape
along the contact surfaces of parts 28, 29 and 30 to protect the surface against glue. Then glue decks in place and and secure
until the glue has dried completely.
Note: Glue two pieces 20.1 to the inside of each sponson, if you want
to secure the steel fin/airtrap to the sponsons with srews later on.
14
15

25
25
25
26
26
27
27
23
23
24
24
Fit stringers 24 to formers along the outside of parts 23 and glue in place. Make sure that stringers are fully seated in notches of formers.
Now is a good time to treat the inside of the hull with wood filler or diluted epoxy resin to protect the wood against moisture.
12
Glue reinforcement 26 and steel plate 27 to frame 25.
Then glue frame 25 to front of parts 23.
Note: Reinforcement and steel plate face down!
13
28
28
28
23
19
20.1
20.1
20.1
30
23
29
30
Flush witht the upper edge glue mahogany panels 28 to the outside of parts 23. Make sure there is a gap of approximately 1.5
to 2 mm between stringer 19 and the lower edge of part 28. Remove any residual glue from the gap.
Insert deck parts 29 + 30 into the gap beneath the side panels 28 and secure temporarily with tape or clamps. Apply tape
along the contact surfaces of parts 28, 29 and 30 to protect the surface against glue. Then glue decks in place and and secure
until the glue has dried completely.
Note: Glue two pieces 20.1 to the inside of each sponson, if you want
to secure the steel fin/airtrap to the sponsons with srews later on.
14
15

36
36
23
31
31
32
33
33 33
34
34
35
35
Glue mahogany panels 31 to 35 in place.
Insert spacers 36 into formers along the inside of parts 23 (but do not glue!), so that they are in full contact with parts 23.
16
17
37
37
38
39
40
38
39
40
Protect the inside of the hull with cling film against
glue, then insert cockpit side panels 37 and press
against spacers 36.
Glue in place cockpit floor 38 as well as front and rear panels 39 + 40. The cling film protects the hull from glue so that the cockpit can be
removed after the glue has dried.
18
19

36
36
23
31
31
32
33
33 33
34
34
35
35
Glue mahogany panels 31 to 35 in place.
Insert spacers 36 into formers along the inside of parts 23 (but do not glue!), so that they are in full contact with parts 23.
16
17
37
37
38
39
40
38
39
40
Protect the inside of the hull with cling film against
glue, then insert cockpit side panels 37 and press
against spacers 36.
Glue in place cockpit floor 38 as well as front and rear panels 39 + 40. The cling film protects the hull from glue so that the cockpit can be
removed after the glue has dried.
18
19

78
79
79
80
81
82
41
41
42
42
37
Use the markings on the side panles as a guide to glue in instrument panel 41. Glue in place cover 42 on side panels 37. Make sure you
protect the hull with cling film before you glue. Glue in place the side cockpit fairings 94. The front edges of parts 94 will need to be adapted
to the hood later on.
20
94
94
94
Glue part 80 to steering wheel 78. Then glue
mahogany rings 79 to either side of steering wheel.
Glue parts 81 to the underside of
the steering wheel, then glue in
steering shaft 82.
21
22
83
84
41
84
83
85
86 86
87
43
44
45
46
47
48
44
49
50
51
52
Glue steering column 83 and
flange 84 to instrument panel 41. Insert steering shaft with steering wheel into
steering column.
23 24
Glue together parts 85 - 87 to assemble throttle lever, then glue
to left inside panel of cockpit.
25
Glue part 43 to part 44 at an angle of 90°. Glue together parts 45 to 48
to form the nose block of the Airmmarine. Sand to a smooth surface when
glue has dried and cover with Oratex.
Glue together parts 101-103 to form the front handle then glue complete
assembly to nose block.
27
Glue together hood from parts 49 to 52: glue together two parts
50, then glue parts 50, 51 and 52 to base plate 49 at an angle of 90°.
Note: The rectangular marking on part 49 faces down!
26
101
102
103

78
79
79
80
81
82
41
41
42
42
37
Use the markings on the side panles as a guide to glue in instrument panel 41. Glue in place cover 42 on side panels 37. Make sure you
protect the hull with cling film before you glue. Glue in place the side cockpit fairings 94. The front edges of parts 94 will need to be adapted
to the hood later on.
20
94
94
94
Glue part 80 to steering wheel 78. Then glue
mahogany rings 79 to either side of steering wheel.
Glue parts 81 to the underside of
the steering wheel, then glue in
steering shaft 82.
21
22
83
84
41
84
83
85
86 86
87
43
44
45
46
47
48
44
49
50
51
52
Glue steering column 83 and
flange 84 to instrument panel 41. Insert steering shaft with steering wheel into
steering column.
23 24
Glue together parts 85 - 87 to assemble throttle lever, then glue
to left inside panel of cockpit.
25
Glue part 43 to part 44 at an angle of 90°. Glue together parts 45 to 48
to form the nose block of the Airmmarine. Sand to a smooth surface when
glue has dried and cover with Oratex.
Glue together parts 101-103 to form the front handle then glue complete
assembly to nose block.
27
Glue together hood from parts 49 to 52: glue together two parts
50, then glue parts 50, 51 and 52 to base plate 49 at an angle of 90°.
Note: The rectangular marking on part 49 faces down!
26
101
102
103

53
54
55 56
57
58
59 60
61
62
63
64
65
66
67
64
68
68
53
54
55
54
104
Glue mahogany strips 53 to 55 into notches of formers.
Glue magnet 104 precisely into rectangular marking on
underside of part 49 and remove any surplus glue around
magnet.
Make up two corner pieces from three parts 50.1 each,
then glue corner pieces to base plate 49 and rear of former
52.
Carefully sand complete hood structure and cover with
Oratex.
49 50.1
28
Glue together the fin from parts 53 to 61. Bevel top edge of part 54 (see red marking) to fit part 57.
Make sure to glue parts 54, 55, 56 and 61 at an angle of 90° to part 53.
29
Glue parts 62 to 68 to either side
of part 59.
30
88
88
88
89
89
93
93
93
105
106
106
Carefully round off the shape of the fin, then cover with Oratex.
31
Attach steering frame 105 with screws 88 and
stop nuts 89 to base plate of outboard motor.
Attach blocks 106 with screws 88 and nuts 89
to frame 105.
Connect steering wires 93 with Z-bends to frame
105.
Adjust motor mount so that the bottom
of the prop hub is level with the bottom
of the hull.
32
33

53
54
55 56
57
58
59 60
61
62
63
64
65
66
67
64
68
68
53
54
55
54
104
Glue mahogany strips 53 to 55 into notches of formers.
Glue magnet 104 precisely into rectangular marking on
underside of part 49 and remove any surplus glue around
magnet.
Make up two corner pieces from three parts 50.1 each,
then glue corner pieces to base plate 49 and rear of former
52.
Carefully sand complete hood structure and cover with
Oratex.
49 50.1
28
Glue together the fin from parts 53 to 61. Bevel top edge of part 54 (see red marking) to fit part 57.
Make sure to glue parts 54, 55, 56 and 61 at an angle of 90° to part 53.
29
Glue parts 62 to 68 to either side
of part 59.
30
88
88
88
89
89
93
93
93
105
106
106
Carefully round off the shape of the fin, then cover with Oratex.
31
Attach steering frame 105 with screws 88 and
stop nuts 89 to base plate of outboard motor.
Attach blocks 106 with screws 88 and nuts 89
to frame 105.
Connect steering wires 93 with Z-bends to frame
105.
Adjust motor mount so that the bottom
of the prop hub is level with the bottom
of the hull.
32
33

70
73
74
107
107
71
72
71
Glue in place mahogany side panels 71. Mark positions of control linkage slots on part 72 and use a small file or
razor saw to cut slots.
Drill holes for motor cables into part 72, then glue part 72 in place.
34
35
Adjust the hight of servo tray 73 and mounting brackets 74 to fit the servo
you want to install, then glue parts into hull.
Install connectors 107 to servo arm. Glue in parts 69 + 70. Drill two 3 mm
holes in part 70 and install outbord motor with screws 91 and stop nuts 92.
98
98
90
89
89
99 100
89.1
89.1
109
106
95
96
97
99
From the outside insert pulley 96 with shaft 95 into cutout in side panel, then glue in place cover 97 over pulley. Route wire 99
over pulleys 96 and through hull.
96
36
37
Drill two 2 mm holes for bracket 98 and install bracket with screws 90, washer 89.1 and
stop nuts 89.
Install turn buckle 109 to bracket 98. Route wire through block 106, sleeve 100, through
ring of turnbuckle 109 and again through sleeve 100.
Use small snub-nosed pliers to squeesze the sleeve at two positions and secure the wire.

70
73
74
107
107
71
72
71
Glue in place mahogany side panels 71. Mark positions of control linkage slots on part 72 and use a small file or
razor saw to cut slots.
Drill holes for motor cables into part 72, then glue part 72 in place.
34
35
Adjust the hight of servo tray 73 and mounting brackets 74 to fit the servo
you want to install, then glue parts into hull.
Install connectors 107 to servo arm. Glue in parts 69 + 70. Drill two 3 mm
holes in part 70 and install outbord motor with screws 91 and stop nuts 92.
98
98
90
89
89
99 100
89.1
89.1
109
106
95
96
97
99
From the outside insert pulley 96 with shaft 95 into cutout in side panel, then glue in place cover 97 over pulley. Route wire 99
over pulleys 96 and through hull.
96
36
37
Drill two 2 mm holes for bracket 98 and install bracket with screws 90, washer 89.1 and
stop nuts 89.
Install turn buckle 109 to bracket 98. Route wire through block 106, sleeve 100, through
ring of turnbuckle 109 and again through sleeve 100.
Use small snub-nosed pliers to squeesze the sleeve at two positions and secure the wire.

Parts List
110
111
Carefully sand the complete model (grade 240 sandpaper) and apply 2 to 3 coats of wood filler. Before you apply each coat,
carefully sand the model. Apply clear varnisch to the bottom parts of the hull or the colour of your choice, and apply several
coats of clear varnish to all mahogany parts.
After the varnish has dried completely, glue or screw the fin/airtrap 110 + 111 to the inside of the sponsons. Seal screws with
clear varnish.
38
No. Description Pieces Material Plate Type Dimensions
0 jig 2 Depron 0 laser cut 3 mm
1-10 formers 10 birch ply 1+2 laser cut 3 mm
11 keel 2 spruce 3 laser cut 4 mm
12 stringer spruce 3 laser cut 4 mm
13 reinforcement 1 birch ply 4 laser cut 2 mm
14 stringer 2 birch ply 4 laser cut 2 mm
15 stringer 2 birch ply 4 laser cut 2 mm
16 stringer 2 spruce 3 laser cut 4 mm
17 stringer 2 spruce 3 laser cut 4 mm
18 bottom/hull 1 birch ply 5 laser cut 1 mm
19 sponson 2 birch ply 6 laser cut 1 mm
20 sponson 2 birch ply 6 laser cut 1 mm
20.1 reinforcement 4 spruce 3 laser cut 4 mm
21 sponson 2 birch ply 6 laser cut 1 mm
22 bottom/hull 2 birch ply 6 laser cut 1 mm
23 side panel 2 birch ply 7 laser cut 1 mm
24 stringer 2 spruce 3 laser cut 4 mm
25 frame 1 mahogany ply 8 laser cut 1.5 mm
26 reiniforcement/frame 1 mahogany ply 10 laser cut 1.5 mm
27 magnet lock 1 steel
28 side panel 2 mahogany ply 9+10 laser cut 1.5 mm
29 left deck panel 1 mahogany ply 9 laser cut 1.5 mm
30 right deck panel 1 mahogany ply 10 laser cut 1.5 mm
31 panel/sponson 2 mahogany ply 9 laser cut 1.5 mm
32 panel/hull side 2 mahogany ply 9 laser cut 1.5 mm
33 panel/transom 2 mahogany ply 9+10 laser cut 1.5 mm
34 panel/motor mount 1 mahogany ply 8 laser cut 1.5 mm
35 panel/motor well 2 mahogany ply 10 laser cut 1.5 mm
36 spacer 2 birch ply 7 laser cut 1 mm
37 side panel/cockpit 2 mahogany ply 8 laser cut 1.5 mm
38 cockpit floor 1 birch ply 12 laser cut 3 mm
39 rear panel/cockpit 1 birch ply 12 laser cut 3 mm
No. Description Pieces Material Plate Type Dimensions
40 front panel/cockpit 1 birch ply 12 laser cut 3 mm
41 instrument panel 1 mahogany ply 8 laser cut 1.5 mm
42 cover 1 mahogany ply 8 laser cut 1.5 mm
43-48 hood nose block 6 obechi 11 laser cut 2 mm
49 hood frame 1 mahogany ply 8 laser cut 1.5 mm
50 hood former 2 mahogany ply 8 laser cut 1.5 mm
50.1 corner piece 6 mahogany ply 8 laser cut 1.5 mm
51 hood former 1 mahogany ply 8 laser cut 1.5 mm
52 hood former 1 mahogany ply 8 laser cut 1.5 mm
53 fin frame 1 birch ply 2 laser cut 3 mm
54-56 fin internal structure 3 birch ply 2 laser cut 3 mm
57-59 fin top structure 3 birch ply 7 laser cut 1 mm
60-61 fin rear end 2 birch ply 7 laser cut 1 mm
62-68 fin doublers 12 obechi 11 laser cut 2 mm
69 floor 1 mahogany ply 8 laser cut 1.5 mm
70 motor mount panel 1 mahogany ply 8 laser cut 1.5 mm
71 left + right panels 2 mahogany ply 9 laser cut 1.5 mm
72 rear motor mount panel 1 mahogany ply 9 laser cut 1.5 mm
73 servo tray 2 birch ply 1 laser cut 3 mm
74 servo tray monting beam 2 birch ply 2 laser cut 3 mm
75 boatstand 1 birch ply 2 laser cut 3 mm
76 boatstand 1 birch ply 2 laser cut 3 mm
77 boatstand 2 birch ply 1 laser cut 3 mm
78 steering wheel 1 nickel silver photo etched 0.5 mm
79 steering wheel cover 2 mahogany ply 9+10 laser cut 1.5 mm
80 ateering wheel cover 1 nickel silver photo etched 0.5 mm
81 steering wheel locating discs 2 mahogany laser cut 0.5 mm
82 steering shaft 1 stainless steel cut part 3 x 50 mm
83 steering column 1 brass cut part 4/3.1 x 40 mm
84 steering shaft flange 1 nickel silver photo etched 0.5 mm
85 throttle lever bracket 2 mahogany ply 8 laser cut 1.5 mm
86 throttle lever housing 2 nickel silver photo etched 0.5 mm
87 throttle lever 1 nickel silver photo etched 0.5 mm
88 screw 4 brass hardware M2x6
89 stop nut 8 metal hardware M2
89.1 washer 2 metal photo etched 0.5 mm
90 screw 4 brass hardware M2x12
91 motor mounting screw 2 brass hardware M3x15
92 stop nut 2 metal hardware M3
93 steering linkage 2 stainless steel cut part 0.8 x 120 mm
94 cockpit fairing 1 mahogany ply 10 laser cut 1.5 mm
95 shaft 2 stainless steel cut part 1.2 x 7 mm
96 pulley 2 brass hardware 8 mm
97 pulley cover 2 nickel silver photo etched 0.5 mm
98 bracket 2 metal hardware
99 push/pull wire 1 stainless steel cut part 0.55 x 1,700 mm
100 sleeve 2 brass hardware 1,8/1,4 mm
101 handle base plate 1 nickel silver photo etched 0.5 mm
102 handle mid section 1 nickel silver photo etched 0.5 mm
103 handle left/right 2 nickel silver photo etched 0.5 mm
104 magnet 1 hardware
105 steering frame 1 nickel silver photo etched 0.5 mm
106 block 2 metal hardware
107 connector 2 metal hardware
108 covering material 1 Oratex cut part
109 turnbuckle 2 brass hardware
110 fin/airtrap 1 stainless steel hardware 0.8 mm
111 fin/airtrap 1 stainless steel hardware 0.8 mm

Parts List
110
111
Carefully sand the complete model (grade 240 sandpaper) and apply 2 to 3 coats of wood filler. Before you apply each coat,
carefully sand the model. Apply clear varnisch to the bottom parts of the hull or the colour of your choice, and apply several
coats of clear varnish to all mahogany parts.
After the varnish has dried completely, glue or screw the fin/airtrap 110 + 111 to the inside of the sponsons. Seal screws with
clear varnish.
38
No. Description Pieces Material Plate Type Dimensions
0 jig 2 Depron 0 laser cut 3 mm
1-10 formers 10 birch ply 1+2 laser cut 3 mm
11 keel 2 spruce 3 laser cut 4 mm
12 stringer spruce 3 laser cut 4 mm
13 reinforcement 1 birch ply 4 laser cut 2 mm
14 stringer 2 birch ply 4 laser cut 2 mm
15 stringer 2 birch ply 4 laser cut 2 mm
16 stringer 2 spruce 3 laser cut 4 mm
17 stringer 2 spruce 3 laser cut 4 mm
18 bottom/hull 1 birch ply 5 laser cut 1 mm
19 sponson 2 birch ply 6 laser cut 1 mm
20 sponson 2 birch ply 6 laser cut 1 mm
20.1 reinforcement 4 spruce 3 laser cut 4 mm
21 sponson 2 birch ply 6 laser cut 1 mm
22 bottom/hull 2 birch ply 6 laser cut 1 mm
23 side panel 2 birch ply 7 laser cut 1 mm
24 stringer 2 spruce 3 laser cut 4 mm
25 frame 1 mahogany ply 8 laser cut 1.5 mm
26 reiniforcement/frame 1 mahogany ply 10 laser cut 1.5 mm
27 magnet lock 1 steel
28 side panel 2 mahogany ply 9+10 laser cut 1.5 mm
29 left deck panel 1 mahogany ply 9 laser cut 1.5 mm
30 right deck panel 1 mahogany ply 10 laser cut 1.5 mm
31 panel/sponson 2 mahogany ply 9 laser cut 1.5 mm
32 panel/hull side 2 mahogany ply 9 laser cut 1.5 mm
33 panel/transom 2 mahogany ply 9+10 laser cut 1.5 mm
34 panel/motor mount 1 mahogany ply 8 laser cut 1.5 mm
35 panel/motor well 2 mahogany ply 10 laser cut 1.5 mm
36 spacer 2 birch ply 7 laser cut 1 mm
37 side panel/cockpit 2 mahogany ply 8 laser cut 1.5 mm
38 cockpit floor 1 birch ply 12 laser cut 3 mm
39 rear panel/cockpit 1 birch ply 12 laser cut 3 mm
No. Description Pieces Material Plate Type Dimensions
40 front panel/cockpit 1 birch ply 12 laser cut 3 mm
41 instrument panel 1 mahogany ply 8 laser cut 1.5 mm
42 cover 1 mahogany ply 8 laser cut 1.5 mm
43-48 hood nose block 6 obechi 11 laser cut 2 mm
49 hood frame 1 mahogany ply 8 laser cut 1.5 mm
50 hood former 2 mahogany ply 8 laser cut 1.5 mm
50.1 corner piece 6 mahogany ply 8 laser cut 1.5 mm
51 hood former 1 mahogany ply 8 laser cut 1.5 mm
52 hood former 1 mahogany ply 8 laser cut 1.5 mm
53 fin frame 1 birch ply 2 laser cut 3 mm
54-56 fin internal structure 3 birch ply 2 laser cut 3 mm
57-59 fin top structure 3 birch ply 7 laser cut 1 mm
60-61 fin rear end 2 birch ply 7 laser cut 1 mm
62-68 fin doublers 12 obechi 11 laser cut 2 mm
69 floor 1 mahogany ply 8 laser cut 1.5 mm
70 motor mount panel 1 mahogany ply 8 laser cut 1.5 mm
71 left + right panels 2 mahogany ply 9 laser cut 1.5 mm
72 rear motor mount panel 1 mahogany ply 9 laser cut 1.5 mm
73 servo tray 2 birch ply 1 laser cut 3 mm
74 servo tray monting beam 2 birch ply 2 laser cut 3 mm
75 boatstand 1 birch ply 2 laser cut 3 mm
76 boatstand 1 birch ply 2 laser cut 3 mm
77 boatstand 2 birch ply 1 laser cut 3 mm
78 steering wheel 1 nickel silver photo etched 0.5 mm
79 steering wheel cover 2 mahogany ply 9+10 laser cut 1.5 mm
80 ateering wheel cover 1 nickel silver photo etched 0.5 mm
81 steering wheel locating discs 2 mahogany laser cut 0.5 mm
82 steering shaft 1 stainless steel cut part 3 x 50 mm
83 steering column 1 brass cut part 4/3.1 x 40 mm
84 steering shaft flange 1 nickel silver photo etched 0.5 mm
85 throttle lever bracket 2 mahogany ply 8 laser cut 1.5 mm
86 throttle lever housing 2 nickel silver photo etched 0.5 mm
87 throttle lever 1 nickel silver photo etched 0.5 mm
88 screw 4 brass hardware M2x6
89 stop nut 8 metal hardware M2
89.1 washer 2 metal photo etched 0.5 mm
90 screw 4 brass hardware M2x12
91 motor mounting screw 2 brass hardware M3x15
92 stop nut 2 metal hardware M3
93 steering linkage 2 stainless steel cut part 0.8 x 120 mm
94 cockpit fairing 1 mahogany ply 10 laser cut 1.5 mm
95 shaft 2 stainless steel cut part 1.2 x 7 mm
96 pulley 2 brass hardware 8 mm
97 pulley cover 2 nickel silver photo etched 0.5 mm
98 bracket 2 metal hardware
99 push/pull wire 1 stainless steel cut part 0.55 x 1,700 mm
100 sleeve 2 brass hardware 1,8/1,4 mm
101 handle base plate 1 nickel silver photo etched 0.5 mm
102 handle mid section 1 nickel silver photo etched 0.5 mm
103 handle left/right 2 nickel silver photo etched 0.5 mm
104 magnet 1 hardware
105 steering frame 1 nickel silver photo etched 0.5 mm
106 block 2 metal hardware
107 connector 2 metal hardware
108 covering material 1 Oratex cut part
109 turnbuckle 2 brass hardware
110 fin/airtrap 1 stainless steel hardware 0.8 mm
111 fin/airtrap 1 stainless steel hardware 0.8 mm

aero-naut Modellbau
Stuttgarter Strasse 18-22
D-72766 Reutlingen
www.aero-naut.com
aero
naut
... and here are some more models from our range
Find out more at www.aero-naut.com
Spitfire 3052/00
Jenny 3055/00
Bellissima 3012/00
Victoria 3082/00
Pilot 3046/00
3042/00-E1-08/2016