Aerpro FP9450BK Guide

Scan QR code
for the install information
VE
DUAL ZONE
INSTALL KIT
USER/INSTALLATION
MANUAL
FP9450BK

Example of factory fitted dual zone stereo
Product overview
The Aerpro FP9450BK VE Facia Installation Kit is Australian designed and
engineered and has been made for fitting a double DIN aftermarket radio, CD or
DVD player to the original double DIN enclosure. It suits VE series 1 dual climate
models with full digital climate control. Compatible models for this kit are select SS
variants and select HSV’s.
1
Inclusions
1x ABS Plastic facia
1x H-VAC controller with built in steering
wheel control module
1x Universal SWC lead
1x Antenna adapter
1x Mounting kit
*NOTE*
The FP9450BK is designed to fit vehicles with an open compartment.
Vehicles with a ‘LID’ compartment will need to replace with either:
Aerpro WC62 (Wireless Charging) or
Aerpro WC62P (Panel Only)

2
1x ABS Plastic facia
1x H-VAC controller with built in steering
wheel control module
1x Universal SWC lead
1x Antenna adapter
1x Mounting kit
Product structure
Screen display
1. Front/Rear demister air button
2. Left rotary dial button (Rotate,Tap,Hold)
3. Right rotary dial button (Rotate,Tap,Hold)
4. Fan speed UP
5. Recirculated air on/off button
6. LCD display information screen
7. Fan speed DOWN
8. USB charging and sync port
12 3 4
5687
Rear Demister Front Demister
Fan Speed
Number/Temp
Outside Temp
Air conditioner
SZ/DZ Indicators
Recirculation air

3
5. Recirculated air on/off button
6. LCD display information screen
7. Fan speed DOWN
8. USB charging and sync port
Functions
Turning air-conditioning ON/OFF
Once powered up, press and hold the right rotary dial button to turn the
air-conditioner on. The LCD screen illuminates and air-conditioner icon
(Snowflake) illuminates. Press and hold again to turn off. When turning on the
air-conditioner the system will remember previous user settings.
Press
& Hold
A
U
T
O
A
U
T
O
A
U
T
O

4
Positioning
To select different air positions in the vehicle tap the RIGHT rotary button. Positions
are for the Head/Feet, Chest, Chest/Feet and Feet (See icons below).
Tap

5
Functions
Recirculation/Air Passthrough button
Tap this button to cycle between Recirculation and Air Passthrough. The
corresponding icon will illuminate.
Tap
A
U
T
O
A
U
T
O

6
Functions
Front/Rear demister button
When air-conditioner is turned on tap this button to active Rear Demister or hold
this button to activate the Front Demister.
Tap
TAP HOLD
Re-Calibrating your HVAC System
In the case that you may need to
re-calibrate you heater valves or ducting
positions. For exampe, your vents do
not pass air through the correct vents or
hot/cold does not feel correct.
Tap and hold the Front Demister
button for 5seconds or more until you
hear the actuators in the car begin to
re-calibrate.
Hold
5secs
A
U
T
O
A
U
T
O
*NOTE*
Turning on Front Demister will
automatically turn on A/C

7
Fan speed
To adjust the fan speed tap on either of the two right buttons.
Top to increase fan speed and Bottom to lower fan speed.
Air-conditioner temperature
Turn the right rotary dial to the left or right to lower and raise the air-conditioner
temperature. This is a numeric value from 15 (lowest) to 29 (highest).
A
U
T
O
A
U
T
O
Rotate
Functions

8
Functions
Automatic climate control
To activate auto climate mode, tap the left hand rotary dial and then set the target
temperature by rotating the right hand rotary dial to the desired level. The fans
speed, the vent temperature and the air flow direction is fully automatic and will
adjust itself based on what it needs to get to the required level.
Tap
A
U
T
O
Rotate
The temperature can be set between
16 and 29 when in Climate Mode.
*NOTE*
When the temperature is set to 16 or
29. The AUTO symbol will turn off.
This indicates the system will be
running full COLD or full HOT

Functions
Automatic climate control continued
When in Auto mode (SZ or DZ), the system is equipped with 3 levels of fan speeds.
Fan LOW, Fan MID and Fan HIGH
A
U
T
O
A
U
T
O
A
U
T
O
Fan LOW Fan MID
Fan HIGH To adjust the levels use Fan Up
and Fan Down
*NOTE*
If you change the Vents while in Auto Climate, the vents will change, however the
fan will remain on AUTO (AUTO Symbol will turn off).
If you change the Air speed above FAN HIGH or FAN LOW while in Auto Climate,
the system will revert back to manual fan mode, however, the Vents will remain on
AUTO (AUTO Symbol will turn off)
9

10
Functions
Passenger Driver
Adjusting Temperature
To adjust the temperature of each zone, rotate the dials. Left for passenger
temperature and Right for drivers side temperature
RotateRotate
Dual Zone
Holding or turning the LEFT rotary dial will activate Dual Zone. The SZ label will
change to DZ and the display will change to a Dual Zone display

11
Functions
Dual Zone
When the LEFT rotary dial is rotated, the passenger temp will be adjusted. Once
this is done, Dual Sync will turn off and both temps can be adjusted independately
Rotate
Rotate
Dual Sync
When the Dual Zone if first activated, the temp for Driver and Passenger will be in
sync. While they are in sync, both temps can be adjusted by the drivers dial

12
Hold
A
U
T
O
A
U
T
O
Anti-Pollution Mode
Anti-Pollution mode will automatically switch between Passthrough and
Re-Circulation based on the vehicles speed. This is to avoid the vehicle drawing in
unwanted fumes when travelling at low speeds
Activating Anti-Pollution Mode
To activate Anti-Pollution Mode, set the
vehicle to Passthrough. Once set, hold
the passthrough button for 5seconds
and wait until you hear a Chime. The
screens symbol will change as shown.
To deactivate Anti-Pollution Mode, hold
the passthrough button for 5 seconds
until you hear 4x Chimes, at which point
the symbol will change back to normal
Functions

13
Turning off Steering Wheel Controls
After ‘5’ seconds of inactivity. The steering wheel controls will revert back to the
aftermarket stereo and functionality will continue as normal
Single Zone
When in Single Zone the Left scroll wheel controls the fan speed and the Right
scroll wheel controls temperature
Dual Zone
When in Dual Zone the Left and Right scroll wheels control the temperature
settings. Left for Passenger temp and Right for Drivers temp.
Steering Wheel Control (SWC)
The climate controls can also be controlled via the steering wheel controls. To
activate the steering wheel mode tap the LEFT dial button. This will illuminate the
steering wheel control symbol on the display
TRIP
NAV
AUDIO
TRIP
AUDIO
Tap
Scroll Scroll
*NOTE*
If no Headunit patch lead is present. The SWC will default to climate controls
Functions

Dash Disassembly
14
Display Example
FRONT REAR
Rear Sensors
The Rear sensors are displayed at the bottom of the screen. There are 3 sections
to indicate the Left, Middle and Right of the Rear of vehicle with each having 4
levels of sensor warnings displayed. This indicates how close to a collision the
vehicle is
Front Sensors
The Front sensors are displayed at the top of the screen. There are 3 sections to
indicate the Left, Middle and Right of the Front of the vehicle with each having 4
levels of sensor warnings displayed. This indicates how close to a collision the
vehicle is
Parking Sensors
Parking sensors are retained if your vehicle had them fitted from factory.
The screen will automatically display the parking sensors when the vehicle is in
Reverse or if the vehicle is travelling less that 15km/h
Functions

15
In the case of the system locking up or not functioning correctly, the unit can be
reset to factory settings.
Press & hold both left & right rotary knobs at the same time.
Press
& Hold
Press
& Hold
Resetting the system

INSTALLATION

*NOTE*
If no Headunit patch lead is present. The SWC will default to climate controls
Before Installation
PLEASE READ BEFORE
INSTALLATION
The system you are installing acts as a controller for
your factory Heating/Cooling system.
To ensure correct functionality, please confirm the
factory system is functioning correctly prior to
installation.
This controller WILL NOT fix any prior issues with the
Heating/Cooling system in the vehicle nor will it convert
a Single Zone vehicle to Dual Zone.
To confirm the factory system is operational, follow the
steps below.
1. Check Fan speed control
2. Check the Vents change correctly
3. Check the system changes temperatue correctly
4. Confirm Dual Zone seperates temperatures correctly
If the system is deemed to be operational, Please
continue with your Installation

1. Panel Remover 2. Phillips Head Screwdriver
3. Flat Head Screwdriver 4. Cordless Drill with 3/8” Drill Bit
5. Small Pick 6. Electrical Tape
7. Cable Ties
+
8. Side Cutters
Use the following tools to make dismantling the car and the installation of the new
facia easier
Tools Needed
2-1

Remove right side dash trim
Insert a panel remover and lever towards you
Remove right side dash trim
Place trim aside safely until trim reassembly
Dash Disassembly
2-2