Afag SE-Power FS User manual

Servo Controller
SE-Power FS
▪Mounting Instructions
Complementary document to the Operating Instruction
© Copyright by Afag Automation AG

2–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
Table of Contents
1General............................................................................................................... 6
1.1 Documentation.................................................................................................... 6
2Safety notes for electrical drives and controllers.................................................. 8
2.1 Used symbols ..................................................................................................... 8
2.2 General Notes..................................................................................................... 9
2.3 Danger resulting from misuse.............................................................................11
2.4 Safety notes.......................................................................................................12
General safety notes..........................................................................................12
Safety notes for assembly and maintenance......................................................14
Protection against contact with electrical parts...................................................15
Protection against electrical shock by means of protective
extra-low voltage (PELV)....................................................................................16
Protection against dangerous movements..........................................................17
Protection against contact with hot parts............................................................17
Protection during handling and assembly...........................................................18
3Technical data....................................................................................................19
3.1 Operating and display elements.........................................................................20
3.2 Supply [X9].........................................................................................................20
3.3 Motor connection [X6] ........................................................................................21
3.4 I/O interface [X1]................................................................................................21
4Functional safety technology..............................................................................22
4.1 Function and application ....................................................................................22
5Mechanical installation.......................................................................................24
5.1 Important notes..................................................................................................24
5.2 View of the device..............................................................................................27
5.3 Mounting............................................................................................................31
6Electrical installation...........................................................................................33
6.1Connector configuration (SE-Power FS 1kVA)...................................................33
6.2 Connector configuration (SE-Power FS 3kVA and 6kVA)...................................34
Connection: Power supply [X9] ..........................................................................36
Connection: Motor [X6].......................................................................................38
Pin assignment [X1] ...........................................................................................39
Connection: RS232/COM [X5]............................................................................40
Cable type and design [X5] ................................................................................40
Connection: USB [X19] ......................................................................................41
Cable type and design [X19] ..............................................................................41
6.3 EMC compliant cabling.......................................................................................42

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 3–50
6.4 ESD protection...................................................................................................43
7Initial operation...................................................................................................44
7.1 General notes on connection..............................................................................44
7.2 Connecting the motor.........................................................................................45
7.3 Connecting the servo positioning controller to the power supply ........................45
7.4 Connecting the PC (USB Interface)....................................................................45
7.5 Connecting the PC (RS232 Interface)................................................................45
7.6 Checking operability...........................................................................................46
7.7 Scaling check.....................................................................................................46
7.8 Switch on controller enable ................................................................................46
8Programming (over digital I/O’s).........................................................................47
List of figures:
Figure 1: Servo positioning controller SE-Power FS 1kVA: Installation space............................25
Figure 2: Servo positioning controller SE-Power FS 3kVA and 6kVA: Installation space...........26
Figure 3: Servo positioning controller SE-Power FS 1kVA: Front view.......................................27
Figure 4: Servo positioning controller SE-Power FS 3kVA and 6kVA: Front view ......................28
Figure 5: Servo positioning controller SE-Power FS 1kVA: Top view .........................................29
Figure 6: Servo positioning controller SE-Power FS 1kVA: Bottom view....................................29
Figure 7: Servo positioning controller SE-Power FS 3kVA and 6kVA: Top view.........................30
Figure 8: Servo positioning controller SE-Power FS 3kVA and 6kVA: Bottom view ...................30
Figure 9: Servo positioning controller SE-Power FS 1kVA: Mounting plate................................31
Figure 10: Servo positioning controller SE-Power FS 3kVA and 6kVA: Mounting plate ...............32
Figure 11: SE-Power FS 1kVA connection to the power supply and motor ..................................33
Figure 12: SE-Power FS 3kVA and 6kVA 1kVA connection to the power supply and motor........34
Figure 13: Supply [X9] SE-Power FS 1kVA...................................................................................36
Figure 14: Supply [X9] SE-Power FS 3kVA and 6kVA ..................................................................37
Figure 15: Pin assignment RS232-null modem cable [X5]............................................................40
Figure 16: Pin assignment: USB interface [X19], front view..........................................................41
Figure 17: Servo positioning controller: Labelling Order................................................................44

4–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
List of tables:
Table 1: Technical data: Ambient conditions and qualification...................................................19
Table 2: Technical data: Dimensions and weight.......................................................................19
Table 3: Technical data: Cable specifications ............................................................................19
Table 4: Technical data: Motor temperature monitoring.............................................................20
Table 5: Display elements and RESET button ...........................................................................20
Table 6: Technical data: Performance data [X9] ........................................................................20
Table 7: Technical data: Motor connection data [X6] .................................................................21
Table 8: Technical Data: digital inputs and outputs [X1] ............................................................21
Table 9: Overview safety activation module for the SE-Power FS.............................................22
Table 10: Fieldbus specific assignment of the r DIP switches......................................................22
Table 11: Pin assignment [X40]....................................................................................................23
Table 12: Pin assignment [X9] SE-Power FS 1kVA .....................................................................36
Table 13: Pin assignment [X9] SE-Power FS 3kVA und 6kVA.....................................................37
Table 14: Pin assignment [X6] SE-Power FS 1kVA .....................................................................38
Table 15: Pin assignment [X6] SE-Power FS 3kVA und 6kVA.....................................................38
Table 16: Pin assignment: I/O communication [X1].....................................................................39
Table 17: Pin assignment RS232 interface [X5]...........................................................................40
Table 18: Pin assignment: USB interface [X19]............................................................................41
Table 19: Dependence power stage and controller enable..........................................................46

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 5–50
This manual is a complementary document to the operating instructions and applies to:
Type
Order No.
Servo Controller SE-Power FS STO 1kVA
50036337
Servo Controller SE-Power FS STO 3kVA
50162993
Servo Controller SE-Power FS STO 6kVA
50183996
Version of this documentation: SE-Power FS-Mounting Instructions-vers. 4.4 en.01.06.2022
Assembly and initial start-up may be carried out by qualified personnel only and according to
these operating instructions.
Caution!
As this manual is a complementary document to the operating instructions it
alone is not sufficient to carry out installation and commissioning of the
device.
Please pay attention to the notes in:
1.1 Documentation

6–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
1General
1.1 Documentation
For the Servo Controllers of the SE-Power series are considerably documentations available.
There are main documents and complementary documents.
The documents contain safety instructions that must be followed.
Main document:
present
documentation / description
☐
▪SE-Power FS Operating manual
Description of the technical data and the functions of the device as well as
notes on the plug assignment, installation and operation of the SE-Power FS
servo controller series.
It is meant for persons who want to get familiar with the SE-Power FS servo
controller
Caution!
The operating manual is the main document and must be read by all means
before installation and start-up of all devices of the SE-Power FS series.
Complementary documents to the operating manual:
present
documentation / description
☒
▪SE-Power FS mounting instructions
This manual is included during delivery of the SE-Power FS devices and
provides an extract from the manual represents the installation instructions
contained therein make sure that they can easily operate the servo drive.
☐
▪SE-Power FS STO-manual
Description of the technical data and the device functionality, installation, and
operation of the safety module STO.
☐
▪SE-Power FS MOV-manual
Description of the technical data and the device functionality, installation, and
operation of the safety module MOV.
☐
▪SE-Power Software-manual
Description of the software SE-Commander with the individual functions.
☐
▪SE-Power CANopen-manual
Description of the implemented CANopen protocol according to CiA DSP402
and DS301.

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 7–50
☐
▪SE-Power FS PROFIBUS/PROFINET-manual
Description of the implemented PROFIBUS-DP and PROFINET protocols, the
technical data and the device functionality, installation, and operation of the
fieldbus-modules „SE-Power Profibus Interface“ and „SE-Power Profinet
Interface“.
☐
▪SE-Power EtherCAT-manual
Description of the fieldbus control by using the CoE (CANopen over EtherCAT)
protocol, the technical data and the device functionality, installation, and
operation of the fieldbus-module „SE-Power EtherCAT Interface“.
☐
▪SE-Power FS programming example Siemens S7 V5.5
Description of the configuration and program from the programming example
for Siemens S7 V5.5.
☐
▪SE-Power FS programming example Siemens S7 TIA V12
Description of the configuration and program from the programming example
for Siemens S7 TIA V12.
☐
▪SE-Power FS Programming example Profinet Siemens S7 TIA
V13/V14
Description of the configuration and program to the programming example for
Profinet for Siemens S7 TIA V13.1 and V14.0.
These documents are available for download on our homepage:
www.afag.com

8–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
2Safety notes for electrical drives and controllers
2.1 Used symbols
Information
Important information and notes.
Caution!
No observance may result in severe property damages.
DANGER!
No observance may result in property damages and in personal injuries.
Caution! Life-threatening voltages.
The safety instruction contains a pointer to the occurrence of a possibly life-
threatening voltage.

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 9–50
2.2 General Notes
In the case of damage resulting from non-compliance of the safety notes in this manual Afag
will assume any liability.
Prior to the initial use you must read the chapters 2 Safety notes for electrical
drives and controller and 6.3 EMC compliant cabling
If the documentation in the language at hand is not understood accurately, please contact
and inform your supplier.
Sound and safe operation of the servo positioning controller requires proper and professional
transportation, storage, mechanical installation, and project planning –with a consideration
of the risks as well as the protective and emergency measures –plus the proper and
professional electrical installation, operation, and maintenance of the devices:
TRAINED AND QUALIFIED PERSONNEL
in the sense of this product manual or the safety notes on the product itself are persons who
are sufficiently familiar with the project, the setup, assembly, commissioning and operation of
the product as well as all warnings and precautions as per the instructions in this manual and
who are sufficiently qualified in their field of expertise:
▪Education and instruction concerning the standards and accident prevention regulations
for the application, or authorisation to switch devices/systems on and off and to ground
them as per the standards of safety engineering and to efficiently label them as per the job
demands.
▪Education and instruction as per the standards of safety engineering regarding the
maintenance and use of adequate safety equipment.
▪First aid training.

10–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
The following notes must be read prior to the initial operation of the system to prevent
personal injuries and/or property damages:
These safety notes must be complied with at all times.
Do not try to install or commission the servo positioning controller before
carefully reading all safety notes for electrical drives and controllers contained in
this document. These safety instructions and all other user notes must be read
prior to any work with the servo positioning controller.
In case you do not have any user notes for the servo positioning controller,
please contact your sales representative. Immediately demand these documents
to be sent to the person responsible for the safe operation of the servo
positioning controller.
If you sell, rent and/or otherwise make this device available to others, these
safety notes must also be included.
The user must not open the servo drive controller for safety and warranty
reasons.
Professional control process design is a prerequisite for sound functioning of the
servo positioning controller!
DANGER!
Inappropriate handling of the servo drive controller and non-compliance of the
warnings as well as inappropriate intervention in the safety features may result in
property damage, personal injuries, electric shock or in extreme cases even
death.

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 11–50
2.3 Danger resulting from misuse
DANGER!
High electrical voltages and high load currents!
Danger to life or serious personal injury from electrical shock!
DANGER!
High electrical voltage caused by wrong connections!
Danger to life or serious personal injury from electrical shock!
DANGER!
Surfaces of device housing may be hot!
Risk of injury! Risk of burning!
DANGER!
Dangerous movements!
Danger to life, serious personal injury or property damage due to unintentional
movements of the motors!

12–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
2.4 Safety notes
General safety notes
The servo drive controller corresponds to IP20 class of protection as well as
pollution level 1. Make sure that the environment corresponds to this class of
protection and pollution level.
Only use replacements parts and accessories approved by the manufacturer.
The devices must be connected to the mains supply as per EN regulations, so
that they can be cut off the mains supply by means of corresponding separation
devices (e.g. main switch, contactor, power switch).
The servo drive controller may be protected using an AC/DC sensitive 300mA
fault current protection switch (RCD = Residual Current protective Device).
Gold contacts or contacts with a high contact pressure should be used to switch
the control contacts.
Preventive interference rejection measures should be taken for control panels,
such as connecting contactors and relays using RC elements or diodes.
The safety rules and regulations of the country in which the device will be
operated must be complied with.
The environment conditions defined in the product documentation must be kept.
Safety-critical applications are not allowed, unless specifically approved by the
manufacturer.
For notes on installation corresponding to EMC, please refer to chapter 6.3 EMC
compliant cabling. The compliance with the limits required by national
regulations is the responsibility of the manufacturer of the machine or system.
The technical data and the connection and installation conditions for the servo
drive controller are to be found in this product manual and must be met.

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 13–50
DANGER!
The general setup and safety regulations for work on power installations (e.g.
DIN, VDE, EN, IEC or other national and international regulations) must be
complied with.
Non-compliance may result in death, personal injury or serious property
damages.
Without any claims to completeness, the following specifications shall apply:
VDE 0100
Regulations for the installation of high voltage (up to
1000V) devices
EN 1037
Safety of machinery - Prevention of unexpected start-up
EN 60204-1
Safety of machinery - Electrical equipment of machines
Part 1: General requirements
EN 61800-3
Adjustable speed electrical power drive systems
Part 3: EMC requirements and specific test methods
EN 61800-5-1
Adjustable speed electrical power drive systems
Part 5-1: Safety requirements - Electrical, thermal and
energy
EN 61800-5-2
Adjustable speed electrical power drive systems
Part 5-2: Safety requirements - Functional
EN ISO 12100
Safety of machinery - General principles for design - Risk
assessment and risk reduction
DIN EN ISO 13849-1
Safety of machinery - Safety-related parts of control
systems Part 1: General principles for design
EN ISO 13849-2
Safety of machinery - Safety-related parts of control
systems Part 2: Validation
More standards to be respected by the user:
EN 574
Safety of machinery - Two-hand control devices
EN 1088
Safety of machinery - Interlocking devices associated with guards
EN 1037
Safety of machinery - Prevention of unexpected start-up
EN ISO 13850
Safety of machinery - Emergency stop

14–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
Safety notes for assembly and maintenance
The appropriate DIN, VDE, EN and IEC regulations as well as all national and local safety
regulations and rules for the prevention of accidents apply for the assembly and maintenance
of the system. The plant engineer or the operator is responsible for compliance with these
regulations:
The servo positioning controller must only be operated, maintained and/or
repaired by personnel trained and qualified for working on or with electrical
devices.
Prevention of accidents, injuries and/or damages:
Additionally secure vertical axes against falling down or lowering after the motor
has been switched off, for example by means of:
▪Mechanical locking of the vertical axle,
▪External braking, catching or clamping devices or
▪Sufficient balancing of the axle.
The motor holding brake supplied by default or an external motor holding brake
driven by the drive controller alone is not suitable for personal protection!
Keep the electrical equipment voltage-free using the main switch and protect it
from being switched on again until the DC bus circuit is discharged, in the case
of:
▪Maintenance and repair work
▪Cleaning
▪long machine shutdowns
Prior to carrying out maintenance work make sure that the power supply has
been turned off, locked and the DC bus circuit is discharged.
The external or internal brake resistor carries dangerous DC bus voltages during
operation of the servo positioning controller and up to 5 minutes thereafter.
Contact may result in death or serious personal injury. Wait for this time prior to
performing any work on the affected connections. Measure the voltages for your
own protection. Contact with these high DC bus circuit voltages may result in
death or serious personal injury.
Be careful during the assembly. During the assembly and also later during
operation of the drive, make sure to prevent drill chips, metal dust or assembly
parts (screws, nuts, cable sections) from falling into the device.
Also make sure that the external power supply of the controller (24 V) is
switched off.
The DC bus circuit or the mains supply must always be switched off prior to
switching off the 24 V controller supply.

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 15–50
Carry out work in the machine area only, if AC and/or DC supplies are switched
off. Switched off output stages or controller enabling’s are no suitable means of
locking. In the case of a malfunction the drive may accidentally be put into
action.
This does not apply to drives with the special “Safe Stop” feature in accordance
with EN 954-1 CAT 3 or with the “Safe Torque Off” feature in accordance with
EN 61800-5-2. This feature can be achieved with the SE-Power FS by
integrating the module SE-Power FS Safety Module STO for example.
Initial operation must be carried out with idle motors, to prevent mechanical
damages for example due to the wrong direction of rotation.
Electronic devices are never fail-safe. It is the user’s responsibility, in the case
an electrical device fails, to make sure the system is transferred into a secure
state.
The servo positioning controller and in particular the brake resistor, externally or
internally, can assume high temperatures, which may cause serious burns.
Protection against contact with electrical parts
This section only concerns devices and drive components carrying voltages exceeding 50 V.
Contact with parts carrying voltages of more than 50 V can be dangerous for people and may
cause electrical shock. During operation of electrical devices some parts of these devices will
inevitably carry dangerous voltages.
DANGER!
High electrical voltage!
Danger to life, danger due to electrical shock or serious personal injury!
The appropriate DIN, VDE, EN and IEC regulations as well as all national and local safety
regulations and rules for the prevention of accidents apply for the assembly and maintenance
of the system. The plant engineer or the operator is responsible for compliance with these
regulations:
Before switching on the device, install the appropriate covers and protections
against accidental contact. Rack-mounted devices must be protected against
accidental contact by means of housing, for example a switch cabinet. The
national regulations for safety/accident prevention must be complied with!
Always connect the ground conductor of the electrical equipment and devices
securely to the mains supply. Due to the integrated line filter the leakage current
exceeds 3.5 mA!
Comply with the minimum copper cross-section for the ground conductor over its
entire length (see for example EN 60800-5-1).

16–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
Prior to the initial operation, even for short measuring or testing purposes,
always connect the ground conductor of all electrical devices as per the terminal
diagram or connect it to the ground wire. Otherwise the housing may carry high
voltages which can cause electrical shock.
Do not touch electrical connections of the components when switched on.
Prior to accessing electrical parts carrying voltages exceeding 50 Volts,
disconnect the device from the mains or power supply. Protect it from being
switched on again.
For the installation the amount of DC bus voltage must be considered,
particularly regarding insulation and protective measures. Ensure proper
grounding, wire dimensioning and corresponding short-circuit protection.
The device comprises a rapid discharge circuit for the DC bus as per EN 60204-
1. In certain device constellations, however, mostly in the case of parallel
connection of several servo positioning controllers in the DC bus or in the case
of an unconnected brake resistor, this rapid discharge may be rendered
ineffective. The servo positioning controllers can carry voltage until up to 5
minutes after being switched off (residual capacitor charge).
Protection against electrical shock by means of protective extra-low voltage
(PELV)
All connections and terminals with voltages between 5 and 50 Volts at the servo positioning
controller are protective extra-low voltage, which are designed safe from contact in
correspondence with the following standards:
International: IEC 60364-4-41
European countries within the EU: EN 61800-5-1
DANGER!
High electrical voltages due to wrong connections!
Danger to life, risk of injury due to electrical shock!
Only devices and electrical components and wires with a protective extra low voltage (PELV)
may be connected to connectors and terminals with voltages between 0 to 50 Volts.
Only connect voltages and circuits with protection against dangerous voltages. Such
protection may be achieved by means of isolation transformers, safe optocouplers or battery
operation.

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 17–50
Protection against dangerous movements
Dangerous movements can be caused by faulty control of connected motors, for different
reasons:
▪Improper or faulty wiring or cabling
▪Error in handling of components
▪Error in sensor or transducer
▪Defective or non-EMC-compliant components
▪Error in software in super ordinated control system
These errors can occur directly after switching on the device or after an indeterminate time of
operation.
The monitors in the drive components for the most part rule out malfunctions in the
connected drives. In view of personal protection, particularly the danger of personal injury
and/or property damage, this may not be relied on exclusively. Until the built-in monitors
come into effect, faulty drive movements must be taken into account; their magnitude
depends on the type of control and on the operating state.
DANGER!
Dangerous movements!
Danger to life, risk of injury, serious personal injuries or property damage!
For the reasons mentioned above, personal protection must be ensured by means of
monitoring or super ordinated measures on the device. These are installed in accordance
with the specific data of the system and a danger and error analysis by the manufacturer.
The safety regulations applying to the system are also taken into consideration. Random
movements or other malfunctions may be caused by switching the safety installations off, by
bypassing them or by not activating them.
Protection against contact with hot parts
DANGER!
Housing surfaces may be hot!
Risk of injury! Risk of burning!
Do not touch housing surfaces in the vicinity of heat sources! Danger of burning!
Before accessing devices let them cool down for 10 minutes after switching them
off.

18–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
Touching hot parts of the equipment such as the housing, which contain heat
sinks and resistors, may cause burns!
Protection during handling and assembly
Handling and assembly of certain parts and components in an unsuitable manner may under
adverse conditions cause injuries.
DANGER!
Risk of injury due to improper handling!
Personal injury due to pinching, shearing, cutting, crushing!
The following general safety notes apply:
Comply with the general setup and safety regulations on handling and assembly.
Use suitable assembly and transportation devices.
Prevent incarcerations and contusions by means of suitable protective
measures.
Use suitable tools only. If specified, use special tools.
Use lifting devices and tools appropriately.
If necessary, use suitable protective equipment (for example goggles, protective
footwear, protective gloves).
Do not stand underneath hanging loads.
Remove leaking liquids on the floor immediately to prevent slipping.

Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4 19–50
3Technical data
Table 1: Technical data: Ambient conditions and qualification
Range
Values
Admissible temperature ranges
Storage temperature:
-25°C to +70°C
Operating
temperature:
0°C to +40°C
+40°C to +50°C at reduced
power 2,5% /K
Admissible installation height
Up to 1000 m above msl, 1000 to 2000 m above msl at
reduced power according to EN 61800-5-1
Humidity
Relative humidity up to 90 %, not bedewing
Protection class
IP20
Pollution degree
1
CE conformity
Low-voltage directive:
EMC regulation:
Current harmonics:
EN 60 800 –5 - 1
EN 61 800 - 3
EN 61 000 - 3 –2
Further certifications
UL certified
Table 2: Technical data: Dimensions and weight
Type
SE-Power FS 1kVA
SE-Power FS
3kVA
SE-Power FS
6kVA
Dimensions including the
mounting plate (H*W*D)
261mm*54,5mm*205mm
334,5mm*69mm*245,5mm
Dimensions (H*W*D)
200mm*54mm*200mm
250mm*69mm*240mm
Weight
approx. 2,1kg
approx. 3,7kg
Table 3: Technical data: Cable specifications
Range
SE-Power
FS 1kVA
SE-Power
FS 3kVA
SE-Power
FS 6kVA
Maximum motor cable length for interference emission as per EN 61800-3
Category C2
Switch cabinet assembly (see chapter 6.3
EMC compliant cabling)
l 25m
l 50m
Category C3
(industrial area)
l 25m
l 50m
Cable capacity of a phase against shield or
between two lines
C‘ 200pF/m

20–50 Mounting Instructions EN ◼SE-Power FS ◼01.06.2022 ◼V4.4
Table 4: Technical data: Motor temperature monitoring
Motor temperature monitoring
Values
Digital Sensor
Normally
closed contact:
Rcold < 500 
Rhot > 100 k
Analogue Sensor
Silicon temperature sensor, for example KTY81, 82 or
similar.
R25 2000 
R100 3400 
3.1 Operating and display elements
On the front, the servo positioning controller SE-Power FS has tree LED‘s and a seven-
segment display to indicate the operating status.
Table 5: Display elements and RESET button
Element
Function
Seven-segment display
Display of operating mode and a coded error number in
the case of a malfunction
LED1
(two-colour LED, green/red)
Operational state respectively fault
LED2 (green)
Controller enable
LED3 (yellow)
Status display CAN bus
RESET-Button
Hardware reset for processor
3.2 Supply [X9]
Table 6: Technical data: Performance data [X9]
Type
SE-Power FS
1kVA
SE-Power FS
3kVA
SE-Power FS
6kVA
Supply voltage (ZME, RME)
1 x 48 VAC
[± 10%]
-
Supply voltage (RE)
1 x 230 VAC
[± 10%]
-
Supply voltage (LME, PME, PME-c,
PEZ, PDZ, OZ, LE, SA)
1 x 230 VAC
[± 10%]
3 x 400 VAC [± 10%]
50…60Hz
Alternative DC supply
(ZME, RME)
48 ... 70 VDC
-
Alternative DC supply (RE)
320 VDC
-
Alternative DC supply
(LME, PME, PME-c, PEZ, PDZ, OZ,
LE, SA)
320 ... 380 VDC
560V DC
In continuous operation maximum of
mains current
4.7 Aeff
5 Aeff
9 Aeff
24V supply
24 VDC [± 20%]
(0,65 A) *)
24 VDC [± 20%] (1 A) *)
*) plus current consumption of a possibly connected holding brake and I/O’s