aFe Power 56-70058D User manual

Cold Air Intake System
Instruction Manual P/N: 56-70058D / 56-70058R______________________________
Make: Hyundai Model: Kona N Year: 2022-2023 Engine: L4-2.0L(t)

Page 2
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Retain factory parts for future use.
Label
Qty.
Description
Part Number
A
1
Air Filter (Pro 5R) For 56-70058R
24-91144
A
1
Air Filter (Pro DRY S) For 56-70058D
21-91144
B
1
Tube
05-5670058B1
C
1
Housing
05-5670058B2
D
1
Coupling, Silicone Reducer: (2-1/2” x 3”) ID x 3’L
05-01736
E
1
Plug, Air Box
05-01527
F
1
Clamp, #048 (2-9/16" - 3-1/2 ")
03-50007
G
1
Clamp, #044 (2-5/16" - 3-1/4")
03-50019
H
1
Fitting, Aluminum 11mm
03-50615
J
1
Fitting, Aluminum 10mm
03-50641
K
2
Push Clip
03-50616
Installation will require the following tools:
Socket set, extension, rachet, adjustable wrench, pliers, and a flat-head screwdriver
Warranty Information available at: https://afepower.com/contact#warranty
Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in
California or for use on any vehicle registered with the California Department of Motor Vehicles.

Page 3

Page 4
Refer to Figure A for Steps 1-2
Step 1: Using pliers, open the clamp securing the larger hose to the air intake tube, then slide the clamp
away from the intake tube. This clamp will be re-used. Disconnect the rubber hose from the air intake
tube.
Step 2: Using pliers, open the clamps securing the smaller hoses to the air intake tube, then slide the clamp
away from the intake tube. These clamps will be re-used. Disconnect the rubber hoses from the air
intake tube.
REMOVAL
Figure A

Page 5
Refer to Figure B for Step 3
Step 3: Loosen the clamp at the turbo inlet.
REMOVAL
Figure B

Page 6
Refer to Figure C for Step 4
Step 4: Loosen the three bolts securing the factory housing to the vehicle. Two (2) of these three bolts will
be re-used during the installation of the Takeda air intake system.
Figure C
REMOVAL

Page 7
Refer to Figure D for Steps 5-6
Step 5: Remove the two (2) push clips connecting the factory air scoop to the front of the car.
Step 6: Remove the housing and air inlet as one piece out of the vehicle.
REMOVAL
Figure D

Page 8
Refer to Figure E for Step 7
Step 7: Transfer the factory grommets and sleeves from the factory housing onto the Takeda housing.
INSTALL
Figure E

Page 9
Refer to Figure F for Steps 8-9
Step 8: Install the Takeda housing into the engine bay.
Step 9: Secure the housing with the two (2) factory bolts removed in Step 4. The bolts will be installed
inside of the Takeda housing.
INSTALL
Figure F

Page 10
Refer to Figure G for Step 10
Step 10: Using a 16mm wrench, install the aluminum fittings into the Takeda air intake tube. The two fittings
are different. The bigger one (with four ribs) goes on the side of the tube. The smaller one (with three
ribs) goes on the top of the tube.
Note: This is an NPT fitting, the small gap between the 16mm hex and the tube is normal.
INSTALL
Figure G
Smaller fitting
(With three ribs)
Bigger fitting
(With four ribs)