aFe Power 46-70049 User manual

®
advanced FLOW engineering
Instruction Manual P/N: 46-70049
Make: Dodge Model: RAM 2500/35000 Year: 2003-2012Engine: L6-5.9/6.7L (td)

®
Label Qty. Description Part Number
A 1 Glide Guard & Hanger Strap 05-60095
B 1 Hanger Strap 05-60095-1
C 12 Flat washers 03-50228
D 4 Aluminum Spacers 05-60130
E 2 M16x2x25 Screws 03-50246
F 2 Hex Nuts 03-50244
G 4 Hex Socket Screws 03-50245
H 2 Hex Head Cap Screws 03-50238
I 1 aFe Logo Plate 05-40101 (Pre-Installed)
J 4 Fillister Head Screws 03-50045 (Pre-Installed)
K 4 Hex Nuts 03-50247 (Pre-Installed)
Installation will require the following tools:
Ratchet, 6mm Allen, 8mm Allen,13mm Socket and Wrench.
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7100.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Disconnect the negative battery terminal before proceeding.
• Retain factory parts for future use.
Page 2

aFepower.com
A B C
D
F
G
H
E
Page 3

®
Refer to Figure A for step 1
NOTE: FOr aFE cOvEr FOllOw sTEps 1-8 & FOr sTOck cOvEr FOllOw sTEps 9-16.
Step 1. Remove the 4 highlighted bolts. These will be used to mount your Glide Guard.
REMOVAL
Page 4
Figure A

Refer to Figure B for step 2
Step 2. Place the Glide Guard on a stand and slide it on to line up the 4 bolt holes.
REMOVAL
aFepower.com
Page 5
Figure B

®
Refer to Figure C for step 3
Step 3. Start all 4 screws by hand and be sure to install a washer on the backside of the Glide
Guard mounting flange and another washer on the front side of the mounting flange.
Figure C
INSTALL
Page 6

Refer to Figure D for step 4
Step 4. Install the hanger strap with the 2 long bolts and washers (hand tighten only).
Figure D
INSTALL
aFepower.com
Page 7

®
Refer to Figure E for step 5
Step 5. Tighten up the 4 mounting screws and torque to 16ft. lbs.
Page 8
Figure E
INSTALL

aFepower.com
Page 9
Refer to Figure F for step 6
Step 6. Install the 2 set screws at the bottom of the Glide Guard. These screws are only to be
hand tightened.
Figure F
INSTALL

®
Refer to Figure G for step 7
Step 7. Tighten down the bolts just until the hanger strap begins to flex.
Page 10
Figure G
INSTALL

aFepower.com
Page 11
Refer to Figure H for step 8
Step 8. Your aFe Power Glide Guard installation is now complete.
NOTE: Retighten all connections after approximately 100-200 miles.
Figure H
INSTALL

®
Refer to Figure H for step 9
Step 9. Remove the 4 highlighted bolts. These will be used to mount your Glide Guard.
REMOVAL
Page 12
Figure H

Refer to Figure I for step 10
Step 10. Place the Glide Guard on a stand and slide it on to line up the 4 bolt holes.
REMOVAL
aFepower.com
Page 13
Figure I

®
Refer to Figure J for step 11
Step 11. Start all 4 screws by hand and be sure to install a spacer on the backside of the Glide
Guard mounting flange and a washer on the front side of the mounting flange.
Figure J
INSTALL
Page 14

Refer to Figure K for step 12
Step 12. Install the hanger strap with the 2 long bolts and washers (hand tighten only).
Figure K
INSTALL
aFepower.com
Page 15

®
Refer to Figure L for step 13
Step 13. Tighten up the 4 mounting screws and torque to 16ft. lbs.
Page 16
Figure L
INSTALL

aFepower.com
Page 17
Refer to Figure M for step 14
Step 14. Install the 2 set screws at the bottom of the Glide Guard. These screws are only to be
hand tightened.
Figure M
INSTALL

®
Refer to Figure N for step 15
Step 15. Tighten down the bolts just until the hanger strap begins to flex.
Page 18
Figure N
INSTALL

aFepower.com
Page 19
Refer to Figure O for step 16
Step 16. Your aFe Power Glide Guard installation is now complete.
NOTE: Retighten all connections after approximately 100-200 miles.
Figure O
INSTALL

®
To purchase any of the items above, view airflow charts, dyno graphs, photos, and video; please go to aFepower.com.
Page 20
P/N: 40-10114 S/M
P/N: 40-10115 L/XL
aFe Power Hat aFe Key Chain
P/N: 40-10103