aFe Power 50-70007D User manual

Momentum HD Cold Air Intake System
Instruction Manual P/N: 50-70007D / 50-70007T__ __ ________________________
Make: Ford Model: Super Duty F-250/F350 Year: 2020-2021 Engine: V8-6.7L (td)

Page 2
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• For technical support please call 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Retain factory parts for future use.
Label
Qty.
Description
Part Number
A1
1
Air Filter (Pro 5R)
24-91061
A2
1
Air Filter (Pro DRY S)
21-91061
B
1
Tube
05-5070007B1
C
1
Housing
05-5070007B2
D
1
Coupling, Silicone Bellows
05-01430
E
2
Clamp, T-bolt (4-9/16" - 4-7/8")
03-50319
F
1
Seal, Trim
05-01553
G
1
Clamp, T-bolt (8-5/16" - 8-5/8")
03-50267
H
1
Plug, Silicone
05-01429
I
2
Screw, Torx: M4x10mm
03-50490
J
4
Retainer Clip
05-01554
K
1
Fixing Clamp, 3/4"ID
03-50234
L
1
Washer, Flat: M6
03-50070
M
1
Screw, Hex Hd: M6x1x20, Gr 8.8
03-50057
Installation will require the following tools:
Panel clip remover, T20 Torx driver, 7mm & 10mm nut drivers, 7mm socket, 10” extension, 11mm deep
socket and driver
Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in
California or for use on any vehicle registered with the California Department of Motor Vehicles.

Page 3
E
D
F
G
J
J
A1/A2
B
C
H
I
K
M
L

Page 4
Refer to Figure A for Step 1
Step 1: Using a 7mm nut driver, loosen the clamps 1 at the turbo inlet and the air filter cover. Remove the
hose 2 from the intake tube clip and remove the intake tube 3 .
REMOVAL
Figure A
1
2
3

Page 5
Refer to Figure B for Steps 2-6
Step 2: Disconnect the MAF sensor 4and the clip 5 holding the harness.
Step 3: Unclip the three taps 6 from the air filter cover.
Step 4: Remove the air filter cover and air filter.
Step 5: Using a panel clip remover, remove the retaining plastic clip 7 holding part of the scoop seal down
and set aside for later use.
Step 6: Snap out the plastic scoop 8 from the air filter housing.
7
REMOVAL
Figure B
4
5
6
8

Page 6
Refer to Figure C for Steps 7-8
Step 7: Using a 7mm socket, extension & driver, remove the screw 9 holding the air filter housing to the
grill inlet duct.
Step 8: Remove the air filter housing by pulling it straight up from its mounting grommets.
REMOVAL
Figure C
9

Page 7
Refer to Figure D for Steps 9-10
Step 9: Place the scoop seal trim 10 on the scoop opening of the aFe POWER housing.
Step 10: Align the holes from the scoop seal trim and the aFe POWER housing. Insert all four retainer clips
11 fully into the cavities and make sure the seal trim is secure to the aFe POWER housing.
10
11
INSTALL
Figure D

Page 8
Refer to Figure E for Step 11
Step 11: Remove the two grommets 12 from the air filter housing and install them onto the aFe POWER
housing. Make sure they are fully seated past the bead.
12
INSTALL
Figure E
12

Page 9
Refer to Figure F for Steps 12-13
Step 12: Install the aFe POWER housing on to vehicle. Make sure the bottom mounting pin is fully seated in
the mounting grommet and the two side mounting pins with grommets are fully engaged on the mounting
bracket.
Step 13: Make sure the scoop seal trim seats behind the plastic trim cover (please see picture). Install the
retaining plastic clip 13 removed on step 5 to secure the trim seal.
13
INSTALL
Figure F
TRIM SEAL TO BE BEHIND PLASTIC TRIM

Page 10
Refer to Figure G for Steps 14-16
Step 14: Slide the large T-Bolt clamp 14 over the air filter opening on the aFe POWER housing.
Step 15: Slide the aFe POWER filter with clamp into the housing. Do not tighten the clamps.
Step 16: Use the provided plug 15 to close the additional air inlet if you want to completely seal the airbox.
Best performance gain is obtained by having more air flow (no plug).
15
14
INSTALL
Figure G