aFe Power SCORPION 79-21004L User manual

advanced FLOW engineering
Instruction Manual P/N: 79-21004L
Scorpion Grille without Forward Facing Camera
Make: Jeep Model: Wrangler (JL) Year: 2018-2020
Make: Jeep Model: Gladiator (JT) Year: 2020

1
•Please read the entire instruction before proceeding.
•Ensure all components listed are present.
•Ensure you have all necessary tools before proceeding.
•Disconnect the negative battery terminal before proceeding.
•If you are missing any of the components, call customer support 951 493 7100
Label
Qty.
Description
A
1
aFe Scorpion Grille
B
1
Bracket, Right Core Support
C
1
Bracket, Left Core Support
D
4
Spacers, Aluminum
E
2
Bracket, Horn
F
2
Retainer, Lower Grille
G
2
Retainer, Upper Grille
H
1
Harness, 7-Way Splitter
I
1
Harness, Power
J
1
Bracket, Air Inlet
K
2
Nuts, #10-24 Extruded U
L
2
Washers, #10
M
4
Nuts, #10-32 Flange
N
2
Bolts, #10-24 Hex Head
O
20
Ties, Cable
P
2
Lights, Low Profile LED
•Applications models vary. We recommend verifying fitment before beginning installation process.
•Images featured in the instruction documents may not always exactly match your grille.
•Does Not fit: Gladiator Sport, Gladiator Sport S.

2

3
Note: Before you begin, use “Painter’s Tape” to apply a protective guard around the work areas. This
will help protect the paint and finish of your vehicle.
1. Disconnect the negative battery terminal.
2. Remove the six (6) push pin retainers from the top of the factory grille. Save the hardware for
reinstallation.

4
3. Pull the top of the grille outward. At the bottom of the grille, there are retainer clips that need to be
removed from the core support. Pull straight out and the clips release.

5
4. Remove the grille from the truck.

6
Note: To prevent scratching painted parts use protective covering between the grille and a flat surface.
5. Remove the four (4) factory Omix-Adam mounting clips. Save for reinstallation.
6. Remove the eight (8) screws that retain the factory inner grille to the factory outer grille. Save the
hardware for reinstallation.

7
7. Remove the factory inner grille from the factory outer grille by releasing the ten (10) retaining clips.
Discard the factory inner grille parts.

8
8. Install the supplied aFe Scorpion grille onto the factory outer grille.

9
9. Install two (2) of the factory screws removed in Step 6 into the outer grille. Do not tighten.

10
10. Make sure to align the aFe Scorpion grille to the factory outer grille. Tighten the two (2) screws
installed in Step 9.

11
11. Install the supplied lower grille retainers using two (2) of the screws removed is Step 6 and
tighten.

12
12. Install the supplied upper grille retainers using two (2) of the screws removed is Step 6 and tighten.

13
13. Install the four (4) supplied aluminum spacers over the factory retainers and secure the factory outer
grille with the four (4) Omix-Adam mounting clips removed in Step 5.

14
14. Install the two (2) supplied low profile LED lights into the aFe Scorpion grille using two (2) supplied
#10-24 extruded U nuts, two (2) supplied #10-24 hex head bolts, and two (2) supplied #10 washers.
Center the lights in the aFe Scorpion grille and tighten.

15
Note: This is what the aFe Scorpion grille assembly should look like after installing the lights.

16
15. Disconnect the horn wiring connectors.

17
16. Remove the horns from their factory brackets.

18
17. Install the horns using the factory hardware onto the two (2) supplied horn brackets.

19
18. Install the horn assemblies onto the studs located at the top of the aFe Scorpion grille using four (4)
supplied #10-32 flanged nuts. The horns electrical connectors need to be facing each other. Tighten all
the hardware.
Electrical connectors face each other