Agilent Technologies 7673 User manual

Operating Manual
Agilent 7673 Automatic Liquid Sampler

Agilent Technologies, Inc.
2850 Centerville Road
Wilmington, DE 1 808-1610
USA
© Agilent Technologies 1995-2000
Target® is a registered trademark and DP™ is a
trademark of National cientific Company.
HP-UX™ is a registered trademark of the
Hewlett-Packard Company.
All Rights Reserved.
Reproduction, adaptation, or translation without
permission is prohibited, except as allowed under
the copyright laws.
Part number G1513-90107
First edition, MAY 2000
Printed in U A
Safety Information
The Agilent Automatic Liquid ampler meets the
following IEC (International Electrotechnical
Commission) classifications: afety Class 1,
Transient Overvoltage Category II, and Pollutions
Degree 2. This unit has been designed and tested
in accordance with recognized safety standards
and designed for use indoors. Whenever the safety
protection of the Automatic Liquid ampler has
been compromised, disconnect the unit from all
power sources and secure the unit against
unintended operation.
The recyclable carbon mono-fluoride lithium
battery is a BR-2/3 A 1,2OO mAh. Fuses F001 and
F002 are 3 A, 250 Vac, IEC 127 Type T. Fuses
F201 and F202 are 10 A, 250 Vac, IEC 127 Type
T. Fuse F101 is a 0.5 A, 250 Vac.
Warnings in this manual or on the instrument must
be observed during all phases of operation, service,
and repair of this instruments. Failure to comply
with these precautions violates safety standards
of design and the intended use of the instrument.
Agilent Technologies assumes no liability for the
customer’s failure to comply with these
requirements. Refer servicing to qualified service
personnel. ubstituting parts or performing any
unauthorized modification to the instrument may
result in a safety hazard. Disconnect the AC power
cord before removing covers. The customer should
not attempt to replace the battery or fuses in this
instrument.
Safety Symbols
This manual contains safety information that
should be followed by the user to ensure safe
operation.
WAR I G
A warning calls attention to a condition or possible
situation that could cause injury to the user.
CAUTIO
A caution calls attention to a condition or possible
situation that could damage or destroy the product
or the user’s work.
Sound Emission Certification for Federal
Republic of Germany
If Test and Measurement Equipment is operated
with unscreened cables and/or used for
measurements in open set-ups, users have to
assure that under these operating conditions the
Radio Interference Limits are still met at the border
of their premises.The following information is
provided to comply with the requirements of the
German ound Emission Directive dated
January 18, 1991:
ound pressure Lp < 70db(A)
During normal operation
At the operator position
According to I O 7779 (Type Test)
When operating the Automatic Liquid ampler with
cryo valve option, the sound pressure ≈ 78 db(A)
during cryo valve operation for short burst pulses.
Schallemission
Werden Meß-und Testgeräte mit ungeschirmten
Kabeln und/oder in offenen Meßaufbauten
verwendet, so ist vom Betreiber sicherzustellen,
daß die Funk-Entströbedingungen unter
Betriebsbedingungen an seiner Grundstücksgrenze
eingehalten werden. Diese Information steht im
Zusammenhang mit den Anforderungen der
Maschinenlärminformation sverordnung vom
18 Januar 1991.
challdruckpegel LP < 70 dB(A)
Am Arbeitsplatz
Normaler Betrieb
Nach DIN 45635 T. 19
(Typprüfung)
Bei Betrieb des Automatischer
lüssigkeitsprobengeber mit Cryo Ventil Option
treten beim Oeffnen des Ventils impulsfoermig
challdrucke Lp bis ca. 78 dB(A) auf.

i
Contents
Chapter 1 Setting Up
The modules of the automatic liquid sampler ....................................................... 3
Preparing the site ...................................................................................................... 5
Environmental considerations ......................................................................... 5
Space considerations ........................................................................................ 5
Electrical power requirements ........................................................................6
Connecting the controller power cord ........................................................... 7
Installing the injectors .............................................................................................. 7
Behind the door to the control switches ........................................................
Before you start ............................................................................................... 10
Mounting the injectors .................................................................................... 11
Checking your work ........................................................................................ 13
Installing the tray ..................................................................................................... 13
Before you start ............................................................................................... 14
Mounting the tray ............................................................................................ 15
Checking your work ........................................................................................ 16
Installing the controller .......................................................................................... 17
Connecting cables to other instruments ...................................................... 18
Setting the configuration switches ................................................................ 1
Configuration switch definitions ................................................................... 1
Connecting the injector cables ...................................................................... 21
Connecting the tray cable ............................................................................... 22
Connecting the controller power cord ......................................................... 22
Checking your work ........................................................................................ 23
Chapter 2 Preparing for Operation
Preparing sample vials ............................................................................................ 26
Selecting and labeling sample vials ............................................................... 26
Specifications ................................................................................................... 27
Sample caps and septum ................................................................................ 28
Filling sample vials .......................................................................................... 2
Crimp capping sample vials ........................................................................... 30
Placing sample vials in the standard injector turret ................................... 32
Placing sample vials in a tray ......................................................................... 33
Using the injector fan .............................................................................................. 34
Turning the fan off ........................................................................................... 34
Preparing the solvent and waste bottles .............................................................. 36
Selecting the bottles ........................................................................................ 36

Contents
ii
Filling and placing the bottles ........................................................................37
Do you need to read further? .........................................................................40
Estimating the maximum number of sample vials ......................................42
Controlling sample carryover .........................................................................47
Selecting and installing syringes ............................................................................4
Selecting syringes ............................................................................................4
Inspecting syringes ..........................................................................................51
Installing syringes ............................................................................................52
Checking your work ........................................................................................53
Maintaining the inlet ................................................................................................54
Changing septa .................................................................................................54
Changing or cleaning liners ............................................................................55
Suggestions for packed inlets with 530-µm columns ..................................55
Adapting for cool on-column injection .................................................................55
Chapter 3 Operation
Setting the run parameters .....................................................................................5
Description of the parameters .......................................................................5
Injection mode ...............................................................................................63
What happens during a run? ...................................................................................66
Checklist ...................................................................................................................68
Running the samples ...............................................................................................6
Starting a run or sequence ..............................................................................6
Stopping or interrupting a run or sequence ..................................................6
Using two injectors ..................................................................................................70
With a tray .........................................................................................................70
Without a tray ...................................................................................................72
Four methods of control .........................................................................................73
Examples of operation ............................................................................................74
Preparing the GC and controlling device ......................................................74
68 0 Series GC Control ...........................................................................................75
Configure tower position ................................................................................75
Configure waste bottle position with a tray .................................................75
Configure the injector .....................................................................................75
Injector parameter setpoints ..........................................................................76
Sample tray setpoints ......................................................................................76
Storing injector setpoints ................................................................................77
Operating in cool on-column mode ...............................................................77

Contents
iii
Creating a sequence ........................................................................................ 78
Storing a sequence .......................................................................................... 7
Starting/running a sequence ........................................................................... 80
Special considerations when using an integrator with a 68 0 Series GC ........ 81
33 6 integrator with a 58 0 GC .............................................................................. 83
Checking your work ........................................................................................ 85
Multitechnique ChemStation control with a 68 0
Series GC .................................................................................................................. 86
Injector parameters ......................................................................................... 86
Washes .............................................................................................................. 87
Position ............................................................................................................. 87
Extended Injector Parameters dialog box ................................................... 88
Start a Run ........................................................................................................ 0
Start a sequence ............................................................................................... 0
Chapter 4 Standalone Control
Setting the run parameters ..................................................................................... 2
Sample size ....................................................................................................... 5
Injection ............................................................................................................ 6
Number of injections per vial ........................................................................ 7
Number of sample prewashes ....................................................................... 8
On-column injection mode .............................................................................
Number of solvent postwashes ................................................................... 100
Example of setting the injector switches ................................................... 101
Setting the position of the last vial .............................................................. 102
Running the samples ............................................................................................. 103
Starting a run or sequence ............................................................................ 103
What happens during a run? ........................................................................ 103
Stopping or interrupting a run or sequence ............................................... 104
Using two injectors ............................................................................................... 106
Synchronous mode ........................................................................................ 106
Asynchronous mode ..................................................................................... 107
Example of standalone control setup ................................................................. 10
Checking your work .............................................................................................. 112
Standalone control ........................................................................................ 112

Contents
iv
Chapter 5 Preventive Maintenance and Troubleshooting
Preventive maintenance ........................................................................................114
Regular basis (before you start a sequence ................................................114
Occasional basis .............................................................................................114
Turret exchange .............................................................................................115
Alignment procedure .....................................................................................116
Troubleshooting .....................................................................................................118
Bent syringe needle ...............................................................................................11
Dropped sample vial ..............................................................................................120
Chromatographic symptoms ................................................................................121
Variability ........................................................................................................121
Contamination or ghost peaks .....................................................................124
Peak area discrimination (smaller or larger peaks than expected) ........126
Sample carryover ...........................................................................................128
No signal/no peaks .........................................................................................12
Fault light symptoms .............................................................................................130
Fault light locations, colors, and patterns ..................................................131
Responding to the fault lights ......................................................................133
Power error .....................................................................................................133
Injector door open/not mounted ..................................................................134
Syringe error ...................................................................................................135
Turret error .....................................................................................................136
Plunger error ..................................................................................................137
Incomplete injection ......................................................................................138
Bottle in gripper .............................................................................................13
Hard tray/injector error .................................................................................140
Align LED is On ..............................................................................................141
Other patterns ................................................................................................142
Error messages ......................................................................................................145
Contacting Agilent Technologies .........................................................................147
Obtaining Agilent Technologies service .....................................................147
Shipment or storage ......................................................................................148

Contents
v
Chapter Special Topics
Performing cool on-column injection onto 250-µm and 320-µm columns ..... 151
Installing the needle into the syringe barrel .............................................. 151
Checking the needle-to-column size ........................................................... 152
Preparing the cool on-column inlet ............................................................. 153
Using retention gaps and other precolumns .............................................. 158
Preparing the injector ................................................................................... 160
Replacing the needle guide in the needle support foot ............................ 165
Troubleshooting 250-µm and 320-µm systems ........................................... 167
Controlling sample vial temperatures ......................................................... 168
Tray control commands ................................................................................ 174
Glossary ...................................................................................... 182
Index ........................................................................................... 191

Contents
vi

1
Setting Up

2
Setting Up
The purpose of this chapter is to:
• Introduce you to the names of the major parts associated with installing
the automatic liquid sampler and some preventive maintenance tips.
• Help you set up the automatic liquid sampler and turn on the power.
You must complete the following tasks during installation to be ready to turn
on the power.
1. Install the mounting brackets for the injector and tray, along with any
upgrade parts for the gas chromatograph (GC). Instructions for these
installations are contained in link manuals that are packaged with the
brackets or upgrade parts.
2. Mount the injector and tray on the brackets.
3. Verify that the controller switch settings are correct.
4. Connect the cables for the injector and tray to the controller.
5. Connect the communication cables for the controller, the GC, and the data
handling device.
6. Install the power cord for the controller.
The instructions for tasks 2 through 6 start on page 11.