Agora Models LAMBORGHINI MIURA Pack 01 Manual

STAGE 1: LEFT DOOR LOCK & HANDLE
STAGE 2: ASSEMBLING THE
WINDOW GLASS AND TYRE
STAGE 3: BUILDING THE DASHBOARD
STAGE 4: INSTRUMENT DIALS
AND CONTROL LEVERS
STAGE 5: ATTACHING THE
LEFT DOOR PANEL
STAGE 6: FITTING THE LEFT
DOOR CLADDING
Pack 01
BUILD INSTRUCTIONS
The “Automobili Lamborghini” and “Automobili Lamborghini Bull and Shield” trademarks, copyrights,
designs and models are used under license from Automobile Lamborghini S.p.A, Italy.

AGORAMODELS LAMBORGHINI MIURA
2
Spare screws are included with each part. Occasionally, you may be instructed to keep spare or
unused screws for a later stage. Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.
Left and Right! When building your Lamborghini Miura, the left or right hand side refers to each
side as you are sitting in the car.
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
Advice from the experts
!

AGORAMODELS LAMBORGHINI MIURA
3
Name
Steering wheel
Left door
Steering wheel emblem
Logo transfer sheet
Door handle
Door lock
STAGE 01 PARTS LIST
In the first stage for this Pack you’ll
begin work on the left-hand side
door by installing the door handle
and lock.
The steering wheel parts and logo
transfer sheet will be used in a later
stage, store these away safely for
the moment.
Left door
Stage 01: Left Door Lock and Handle
Steering wheel emblem
Steering wheel
Logo transfer sheet Door handle Door lock

AGORAMODELS LAMBORGHINI MIURA
4
1
3
2
4
Take the left door part. Note the three holes under the black fins of the
engine’s side air intake (circled). The door lock and door handle will be
inserted into these holes.
Lightly press the door lock into place.
Take the door lock and align it with the two small holes on the
left door as shown. Note: given the very small size of the piece, we
recommend handling it with modeling tweezers.
Now you can attach the handle, orienting it as shown in the picture.
This piece features two pins, one of which is inserted into the available
hole in the door (arrow) and the other in the small hole on the outer
edge of the door (see photo 5).
Stage 01: Left Door Lock and Handle

AGORAMODELS LAMBORGHINI MIURA
5
5
7
6
This photo shows the edge of the door with the small notch into which
the second pin fits (right arrow) and a surface groove that guides the
fitting of the handle (left arrow).
With both the handle and lock in place, the left door should look like this.
Carefully slide the door handle into place.
Stage 01: Left Door Lock and Handle

AGORAMODELS LAMBORGHINI MIURA
6
STAGE COMPLETE
Stage 01: Left Door Lock and Handle

AGORAMODELS LAMBORGHINI MIURA
7
Name
Left window glass
Wheel rim
Chromed glass frame
Pirelli tyre
Type A screws x3
Screwdriver
STAGE 02 PARTS LIST
In this next stage, you’ll assemble
the first wheel of the Lamborghini
Miura and install the window on the
left-hand door from the first stage.
Stage 02: Assembling the Window Glass and Tyre
Chromed glass frame
Left window glass
Pirelli tyre
Type A x3 Screwdriver
Wheel rim

AGORAMODELS LAMBORGHINI MIURA
8
1
3
2
4
Align the Pirelli tyre and the wheel rim as shown.
Once the rim is fitted inside, make sure the side walls of the tyre fit
snugly over the wheel rim on both sides. The photo shows the external
side of the wheel.
Holding the tyre in one hand and the rim in the other, squeeze the rim
into the tyre.
The internal side of the wheel should look like this.
Stage 02: Assembling the Window Glass and Tyre

AGORAMODELS LAMBORGHINI MIURA
9
5
7
6
8
Now take the left window glass and the chromed glass frame and
align them as shown. The holes in the chromed frame fit over the lugs
at the base of the glass (arrows).
Lay the left door from the previous stage on your work surface. Align
the window glass with the door so that the chromed frame is facing
outwards. The lugs from the door glass fit onto two screw holes on
the door.
Place the chromed frame onto the glass, pressing lightly until the
parts click together.
Carefully press the glass and frame onto the door.
Stage 02: Assembling the Window Glass and Tyre

AGORAMODELS LAMBORGHINI MIURA
10
9 10
Secure the parts together using 2x Type A screws supplied. The outside of the door should look like this once complete.
Stage 02: Assembling the Window Glass and Tyre
STAGE COMPLETE
TYPE A