Agora Models JAGUAR E-TYPE Manual

STAGE 65: GLOVE COMPARTMENT
& GRAB HANDLE
STAGE 66: REAR FLOOR
STAGE 67: SPARE WHEEL
& REAR FLOOR COVERS
STAGE 68: FUEL TANK TOP AND BASE
STAGE 69: LEFT REAR WHEEL ARCH
STAGE 70: RIGHT REAR WHEEL ARCH
STAGE 71: HEADLIGHTS
STAGE 72: RIGHT FRONT WING & LIGHTS
STAGE 73: LEFT FRONT WING & LIGHTS
Pack 09
BUILD INSTRUCTIONS

AGORAMODELS JAGUAR E-TYPE
2
Spare screws are included with each part. Occasionally, you may be instructed to keep spare or
unused screws for a later stage. Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.
Left and Right! When building your Jaguar, the left or right hand side refers to each side as you
are sitting in the car.
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
Advice from the experts
!

AGORAMODELS JAGUAR E-TYPE
3
Name
Dashboard top
Grab handle
Glove compartment
Screws type AG06 x5
STAGE 65 PARTS LIST
In the first stage of this Pack you’ll
continue work on the dashboard
by fitting on the dashboard top
as well as installing the glove
compartment and grab handle.
Grab handle
Stage 65: Glove Compartment & Grab Handle
AG06 x5
Dashboard top
Glove compartment

AGORAMODELS JAGUAR E-TYPE
4
1
3
2
4
Take the dashboard assembly from Stage 64. Align the glove
compartment with the dashboard as shown and fit into place using
the screw holes as a guide (arrows).
Next take the dashboard top and align with the dashboard, so that the
notches (circled) are facing as shown. Fit the dashboard top in place.
Secure the glove compartment in place using 2x AG06 screws.
Fix in place using 2x AG06 screws.
Stage 65: Glove Compartment & Grab Handle
AG06
AG06

AGORAMODELS JAGUAR E-TYPE
5
56
Now move to the front of the dashboard, and align the grab handle as
shown. The plugged end of the handle fits into the hole on the
left-hand side of the dashboard (arrow).
Carefully push the grab handle into place.
Stage 65: Glove Compartment & Grab Handle
STAGE COMPLETE

AGORAMODELS JAGUAR E-TYPE
6
Name
Rear floor
Screws type AG06 x4
STAGE 66 PARTS LIST
In this stage you’ll extend the base
of the floor by attaching the rear
floor to the cockpit assembly.
AG06 x4
Stage 66: Rear Floor
Rear floor

AGORAMODELS JAGUAR E-TYPE
7
1
Take the cockpit floor assembly from Stage 62 and lay it upside down,
then align the rear floor with the cockpit as shown. Fit the rear floor by
pressing the three screw hole recesses onto the corresponding screw
holes on the cockpit (arrows).
Stage 66: Rear Floor
2
Attach the rear floor to the cockpit using 3x AG06 screws.
STAGE COMPLETE
AG06

AGORAMODELS JAGUAR E-TYPE
8
Name
Spare wheel cover
Rear floor cover
Pull handle
STAGE 67 PARTS LIST
Continue working on the floor as
you fit the covers for the spare
wheel compartment and the rear
floor from the previous stage.
Note: both covers in this stage are
loose fits, so they can be stored
away safely for now if preferred.
Pull handle
Stage 67: Spare Wheel & Rear Floor Covers
Rear floor coverSpare wheel cover

AGORAMODELS JAGUAR E-TYPE
9
1
3
2
4
Take the spare wheel cover and pull handle, noting the D-shaped hole
(circled) on the cover.
The spare wheel cover can now be placed into the corresponding
recess of the rear floor.
Press the D-shaped plug on the pull handle into the spare wheel cover.
Stage 67: Spare Wheel & Rear Floor Covers

AGORAMODELS JAGUAR E-TYPE
10
56
With the spare wheel cover in place, the rear floor cover fits over the
top. Both covers are not secured in place, so can be stored away in a
safe place for a later stage if preferred.
This image shows the placement of the rear floor cover over the top of
the spare wheel cover.
Stage 67: Spare Wheel & Rear Floor Covers
STAGE COMPLETE