Agora Models Jaguar E-Type Pack 10 Manual

STAGE 74: RIGHTHAND HEADLIGHT COVER
AND VALANCE
STAGE 75: LEFTHAND HEADLIGHT COVER
AND VALANCE
STAGE 76: ATTACHING THE STONE GUARD
STAGE 77: THE FRONT UNDERPANEL
STAGE 78: REAR LEFT WHEEL OUTER RIM
STAGE 79: REAR LEFT WHEEL 
FITTING THE INNER SPOKES
STAGE 80: REAR LEFT WHEEL 
FITTING MORE SPOKES
STAGE 81: REAR LEFT WHEEL 
FITTING THE TYRE
STAGE 82: THE BOOT COVER
Pack 10
BUILD INSTRUCTIONS

AGORAMODELS JAGUAR E-TYPE
2
Spare screws are included with each part. Occasionally, you may be instructed to keep spare or
unused screws for a later stage. Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.
Left and Right! When building your Jaguar, the left or right hand side refers to each side as you
are sitting in the car.
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
Advice from the experts
!

AGORAMODELS JAGUAR E-TYPE
3
Name
Right-hand valance
Right headlight surround
Right headlight glass cover
Bonnet grille and catch
Screws type AM09 x3
Screws type AM15 x4
STAGE 74 PARTS LIST
In this first stage of Pack 10 you’ll fit
the valance, which reinforces and
improves airflow of the bonnet, as
well as assembling and attaching
the cover for the right headlight.
The bonnet grille and catch are also
fitted in this stage.
Stage 74: Right-hand Headlight Cover and Valance
AM15 x4
Right-hand valance Right headlight surround Right headlight glass cover
Bonnet grille and catch
AM09 x3

AGORAMODELS JAGUAR E-TYPE
4
1
3
2
4
Take the bonnet assembly from Stage 73. Align the bonnet grille and
catch with the two holes on the underside of the bonnet as shown.
Next align the valance with the bonnet as shown. The three screw
holes of the valance fit over the corresponding holes located on the
bonnet (arrows).
Fit the bonnet grille and catch into place, then secure in place with 2x
AM09 screws.
Fit the valence in place then secure to the bonnet using 3x AM15
screws.
Stage 74: Right-hand Headlight Cover and Valance
AM09
AM15

AGORAMODELS JAGUAR E-TYPE
5
56
Now take the right headlight surround and glass cover. Note the
three lugs (arrows) and tabs (circled) for fitting the parts together. We
recommend test fitting the two parts before proceeding.
When happy with the fit, apply a small amount of PVA glue to the
surround. This should stop the glass popping out after the headlight
cover has been put in place.
Stage 74: Right-hand Headlight Cover and Valance
7 8
Firmly press the two parts together so that the fit is flush and allow
the glue time to dry.
Before pushing the headlight cover in place, we recommend cleaning
the inside with a cloth to remove any traces of dust and fingerprints
from the glass.

AGORAMODELS JAGUAR E-TYPE
6
910
Align the headlight cover with the right-hand headlight as shown.
Take care to fit the notch (inset) into place first, then press the cover
until it sits over the headlight.
The cover should look like this once it has been fitted onto the bonnet
over the headlight.
Stage 74: Right-hand Headlight Cover and Valance
STAGE COMPLETE

AGORAMODELS JAGUAR E-TYPE
7
Name
Left-hand valance
Heater air intake
Left headlight surround
Left headlight glass cover
Screws type AM15 x4
STAGE 75 PARTS LIST
The next stage is to fit the left-hand
valance to the bonnet, which features
the air intake for the heaters. You’ll
assemble and attach the left headlight
cover as well.
Stage 75: Left-hand Headlight Cover and Valance
AM15 x4
Left-hand valance
Left headlight surround Left headlight glass cover
Heater air intake

AGORAMODELS JAGUAR E-TYPE
8
1
3
2
4
Take the heater air intake and align it with the left-hand valance as
shown. Note the indent in the valance to accommodate the heater air
intake (arrow).
Next align the valance with the bonnet as shown. The three screw
holes of the valance fit over the corresponding holes located on the
bonnet (arrows).
Firmly press the heater air intake onto the valance.
Fit the part in place then secure to the bonnet using 3x AM15 screws.
Stage 75: Left-hand Headlight Cover and Valance
AM15

AGORAMODELS JAGUAR E-TYPE
9
5
7
6
8
Now take the left headlight surround and glass cover.
Firmly press the two parts together so that the fit is flush and allow the
glue time to dry. As you did with the previous headlight cover, clean
the parts to remove any dust or fingerprints from the glass.
Apply a small amount of PVA glue to the surround.
Fit the headlight cover in place, taking care to fit the notch (inset) into
place first.
Stage 75: Left-hand Headlight Cover and Valance

AGORAMODELS JAGUAR E-TYPE
10
Stage 75: Left-hand Headlight Cover and Valance
STAGE COMPLETE