Agora Models SHELBY COBRA 427 S/C User manual

1
AGORAMODELS SHELBY COBRA 427 S/C
STAGE 83: OIL COOLER BRACKETS AND FLUID
PIPE
STAGE 84: AIR INLETS AND EXPANSION
TANK PARTS
STAGE 85: MAIN COBRA BODY & DOOR
LOCKS
STAGE 86 : SIDE MIRROR PARTS, RADIATOR
BRACKET, HOOD HINGES & MOUNTING PLATE
STAGE 87: LEFT INNER SIDE PANEL & DOOR
ARCH TRIM
STAGE 88: RIGHT INNER SIDE PANEL & DOOR
ARCH TRIM
STAGE 89: ELECTRICAL WIRES
STAGE 90: LEFT FENDER GRILLE
& JACKING PADS
Pack 11 |Build Instructions
In the 1960s, Carroll Shelby’s Cobras dominated racetracks worldwide, first winning races coast to coast
across North America, then in 1965, winning the World Manufacturer’s GT Championship, achieving the
ultimate goal of defeating Ferrari. The Semi-Competitions were modified from full competition models
just enough to make them street legal. Only 29 models were produced, making them one of the most
sought-after American sports cars by collectors.
Your 1:8 model replicates the original 1965 Semi-Competition Cobra in intricate detail. From the detail on
the dashboard dials to the writing on the wheels, every piece is precisely reproduced.
In your eleventh model pack, you will assemble:

2
AGORAMODELS SHELBY COBRA 427 S/C
Name Quantity
Left oil cooler bracket 1
Right oil cooler bracket 1
Left hose 1
Right hose 1
Screws TYPE OP01 3
Screws TYPE OP08 3
STAGE 83 PARTS LIST
In this first stage of Pack 11, you
will fix the oil cooler brackets and
radiator to the mounting frame and
add the fluid pipes.
Stage 83: Oil Cooler Brackets And Fluid Pipe
Left oil cooler bracket Right oil cooler bracket
Left hose
Right hose
Screws

3
AGORAMODELS SHELBY COBRA 427 S/C
STEP 1
1
2
3
4
ATTACH THE OIL COOLER BRACKETS
Align the Left Oil Cooler Bracket with the
corresponding holes on the Radiator Mounting
Frame. Fix in place from the reverse side using 1 x
TYPE OP01 screw.
Repeat on the right side to attach the Right Oil
Cooler Bracket.
Stage 83: Oil Cooler Brackets And Hoses
1 x OP01

4
AGORAMODELS SHELBY COBRA 427 S/C
STEP 2
5
6
1
2
ATTACH THE RADIATOR TO THE
MOUNTING FRAME
Align the two tabs on the side of the Radiator
with the two raised screw holes on the Radiator
Mounting Frame. Secure in place using 2 x TYPE
OP08 screws.
Stage 83: Oil Cooler Brackets And Hoses
1 x OP01
CONTINUED...
2 x OP08

5
AGORAMODELS SHELBY COBRA 427 S/C
STEP 3
1
2
3
4
FIX THE HOSES IN PLACE
Feed the Left Hose through the square hole on the
left side of the Radiator Mounting Frame. Check
you have the hose the correct way round, with the
end shown in picture 1 leading towards the Oil
Cooler. Push the end of the hose into the hole on
the Oil Cooler.
Repeat with the Right Hose on the right side of
the Oil Cooler (picture 4).
Stage 83: Oil Cooler Brackets And Hoses

6
AGORAMODELS SHELBY COBRA 427 S/C
5
Stage 83: Oil Cooler Brackets And Hoses
Stage 83 complete!
CONTINUED...

7
AGORAMODELS SHELBY COBRA 427 S/C
Name Quantity
Left air inlet 1
Right air inlet 1
Expansion tank bottom 1
Expansion tank top 1
Expansion tank cap 1
Screws TYPE OP08 4
Screws TYPE OP16 2
STAGE 84 PARTS LIST
In stage 84, you will attach the air
inlets and expansion tank.
Stage 84: Air Inlets And Expansion Tank Parts
Left air inlet Right air inlet
Expansion tank bottom
Expansion tank top
Expansion tank cap
Screws

8
AGORAMODELS SHELBY COBRA 427 S/C
STEP 1
1
2
3
4
ATTACH THE AIR INLETS
Align the screw holes on the Right Air Inlet with
the hole on the Radiator Mounting Frame. Fix in
place using a TYPE OP08 screw.
Repeat to fix the Left Air Inlet on the left side of
the Radiator Mounting Frame.
Stage 84: Air Inlets And Expansion Tank Parts
1 x OP08

9
AGORAMODELS SHELBY COBRA 427 S/C
STEP 2
5
6
1
2
ATTACH THE EXPANSION TANK
Align the screw holes on the Expansion Tank
Bottom with the bracket as shown in picture 1. Fix
in place using a TYPE OP08 screw.
Stage 84: Air Inlets And Expansion Tank Parts
CONTINUED...
1 x OP08
1 x OP08

10
AGORAMODELS SHELBY COBRA 427 S/C
3
4
5
6
7
Stage 84: Air Inlets And Expansion Tank Parts
1 x OP16
CONTINUED...
Position the Expansion Tank Cap on the Expansion
Tank Top and seceure from the underside using a
TYPE OP16 screw.
Place the Expansion Tank Top onto the bottom
part and push them together to fix.