Airaid 300-143 Service manual

Installation Instructions
For Part Numbers:
300-143 700-450 Airaid Oiled Media Filter
301-143 701-450 SynthaMax Dry Media Filter - Red
302-143 702-450 SynthaMax Dry Media Filter - Black
303-143 703-450 SynthaMax Dry Media Filter - Blue
2004-08 Dodge Durango 4.7L V8, 5.7L V8
2007-08 Chrysler Aspen 5.7L V8
2. Loosen the hose clamp on the air box lid and
remove the lid from the air box base.
3. Using a 13mm socket, remove the air box base
from the engine compartment. Using a flat blade
screwdriver, carefully unsnap the box inlet from the
base and remove it. Reinstall the factory base in the
engine compartment without the inlet.
4. Using the supplied #6 screws, nuts and washers,
assemble the two panels as shown above. Next,
install the supplied air filter adapter using the sup-
plied ¼-20 bolts and washers.
5. Install the supplied nylon fitting into the air fil-
ter adapter as shown.
6. Install the Airaid Cool Air Dam assembly on top
of the factory air filter base. Reconnect the factory
intake tube, and tighten the hose clamp.
8. 5.7 Hemi engines only. Using the supplied
straight ¾” hose, connect both ends to the nylon
fitting and oil fill nipple as shown. Fasten both
ends using the supplied nylon speed clamps. Ad-
just the nylon fitting downward to clear the factory
intake tube assembly.
7. 4.7L engines only. Using the supplied pre-
formed 3/4” hose, connect the nylon fitting to the
remaining plastic factory hose as shown. Fasten
both ends of the hose using the supplied nylon
speed clamps. Adjust the fitting downward to clear
the factory intake tube assembly.
9. Install the Airaid Premium Filter on the end of the
air filter adapter, and tighten the hose clamp. Install
the supplied weather strip on the Cool Air Dam.
(Note: start from one end and work your way around
to insure proper alignment of weather strip.)
Component Identification
1. Airaid Premium Filter 1
2. Air Filter Adapter 1
3. MAF Panel 1
4. Front Panel 1
5. ¾” x 25” Black Hose 1
6. 90º ¾” Molded Hose 1
7. Weather Strip 17” 1
8. Speed clamp 2
9. ¼-20 Button Head Screw 2
10. ¼” Flat Washer 2
11. 6-32 x 5/16” Phillips Screw 4
12. #6 Flat Washer 4
13. 6-32 Keps Nut 4
14. ¾” Nylon Elbow 1
1.Disconnect The Negative Battery Terminal!
Disconnect the factory breather hose and remove
from the vehicle. (Note: 4.7L engines require the
removal of the breather hose end section only. 5.7L
Hemi required removal of entire hose assembly.
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [email protected] www.airaid.com
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week-
days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA-
TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.
REV.11.1.13
FILTER IDENTIFICATION
700-450 Airaid Oiled Media 701-450 Airaid SynthaMax Dry Media - Red
702-450 Airaid SynthaMax Dry Media - Black 703-450 Airaid SynthaMax Dry Media - Blue
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning with
common non-petroleum all-purpose house-
hold cleaner and water. Simple Green®,
Formula 409® or equivalent works great.
Apply cleaner to outside of air filter and al-
low to soak. Then flush filter clean from the
inside out with a garden hose and repeat
steps if necessary. Do not apply high pres-
sure water or air to clean filter. Allow filter
to air dry and reinstall.
For your Oiled media filter
we suggest using the AIRAID
Filter Tune-Up Kit!
10. Double check your work to be certain that all
nuts, bolts, and clamps are securely fastened.
11. Reconnect the negative battery cable.