Airaid 450-756 User manual

Installation Instructions
450-756 850-344 Airaid Oiled Media Filter
451-756 851-344 SynthaMax Dry Media Filter - Red
Component Identication
2018 FORD Mustang GT
V8-5.0L
For Part Numbers:
Full color instructions can be viewed on our web site at Airaid.com. If you need any assistance please call 1-800-498-6951 to speak with
a representative in our Customer Service Center before returning the product.
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
1. Turn o the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories. Write
down all memory settings before disconnecting the
negative battery cable. Some radios will require
an anti-theft code to be entered after the battery is
reconnected. The anti-theft code is typically supplied
with your owner’s manual. In the event your vehicles
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles anti-
theft code.
TO START:
Description Qty. Part #
A
B
C
D
E
F
G
HIJ
FACTORY
PART
FACTORY
PART
K
L
A
A HOSE CLAMP #56 2 08620
B HOSE; HUMP 3.5"ID X 2.5"L 1 KITCOUPLER09
C VENT FITTING 3/8” 1 82631
D GROMMET 3/8” ID 1 08100
EINTAKE TUBE 1 KIT756A
F GROMMET 1/2” ID 1 08064
G VENT FITTING 1/2” 1 82629
H HOSE CLAMP #60 STAINLESS 1 08628
I HOSE; HUMP 4"ID X 3"L 1 KITHUMPHS48
J HOSE CLAMP #64 STAINLESS 1 08645
K AIR FILTER 1 850/851-344
L CAPLUG 1 08246
2. Remove the four nuts that secure the strut brace and
then remove the strut brace from the vehicle. Pop up the
two-round bolt covers.
3. Remove the two nuts that secure the decorative engine
cover and remove the cover from the engine.
4. Release the spring clamp that secures the sound tube
to the intake tube tting and then disconnect the sound
tube from the intake tube. Disconnect the quick connect
vent lines shown.
6. Release the one-time use clamp that secures the sound
tube to the drum and then disconnect and remove the
sound tube from the vehicle.
5. Loosen the hose clamps that secure the intake tube to
the air lter housing and throttle body and then remove
the intake tube from the vehicle.
NOTE: AIRAID recommends that customers do not
discard factory air intake.

AIR-I45756
REV 11/07/18
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions regarding t or instructions that are
not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing,
contact Airaid. The air lter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water.
WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air lter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
850-344 Airaid Oiled Media 851-344 Airaid SynthaMax Dry Media - Red
Synthamax Air Filters do not require oil. Service
air lter as needed by cleaning with common
non-petroleum all-purpose household cleaner
and water. Simple Green®, Formula 409® or
equivalent works great. Apply cleaner to outside of
air lter and allow to soak. Then ush lter clean
from the inside out with a garden hose and repeat
steps if necessary. Do not apply high pressure
water or air to clean lter. Allow lter to air dry
and reinstall.
Airaid. 1455 Citrus St., P.O. Box 1329, Riverside, CA. 92502 1-800-498-6951 [email protected] www.airaid.com
For your Oiled media lter we oer the
Airaid Tune Up Kit!
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
14. Double check your work!
Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.
Double check the hood clearance!
Reconnect the negative battery cable!
Continued...
7. Install the provided caplug onto the sound drum.
8. Release the clips the secure the upper air lter
housing and then remove the factory air lter. Install the
AIRAID® replacement air lter and resecure the upper
housing with the factory clips.
9. Install the provided coupler onto the throttle body and
secure with the provided hose clamp.
10. Install the provided coupler hose onto the air lter
housing and secure with the provided hardware.
11. Install the provided vent ttings into the AIRAID®
intake tube as shown.
12. Install the AIRAID®intake tube assembly into the
coupler hoses, adjust for best t and then secure with the
provided hose clamps. Connect the factory vent lines to
the ttings installed into the intake tube.
13. Reinstall the strut brace and decorative engine cover.