Airaid 401-762 User manual

Installation Instructions
400-762 860-397 Airaid Oiled Media Filter
401-762 861-397 SynthaMax Dry Media Filter - Red
Component Identication
2018 FORD F150
V6-3.3L
For Part Numbers:
Full color instructions can be viewed on our web site at Airaid.com. If you need any assistance please call 1-800-498-6951 to speak with
a representative in our Customer Service Center before returning the product.
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
1. Turn o the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories. Write
down all memory settings before disconnecting the
negative battery cable. Some radios will require
an anti-theft code to be entered after the battery is
reconnected. The anti-theft code is typically supplied
with your owner’s manual. In the event your vehicles
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles anti-
theft code.
TO START:
FACTORY
PART
FACTORY
PART
ABC
D
E
E
F
CH
I
G
Description Qty. Part #
A HOSE CLAMP #48 1 08601
B HOSE; 3.5" TO 3"ID X 3"L TPRD 1 084055
C HOSE CLAMP #56 2 08620
DINTAKE TUBE (MP) 1 KIT762
E VENT; 1/4 NPT QUICK 2 082628
F CABLE TIE; 6", BLACK 1 1-127
G HOSE; HUMP 3.5"ID TO 3.75" 1 08639
H HOSE CLAMP #60 STAINLESS 1 08628
I FILTER 1 860/861-397
2. Release the locking tabs and then disconnect the
Crank Case vent lines from the intake tube.
3. Unclip the harness and hose support from the intake
tube. Loosen the hose clamps that secure the intake tube
to the throttle body and air lter housing then remove
the intake tube from the vehicle.
NOTE: AIRAID recommends that customers do not
discard factory air intake.
5. Release the clips that secure the upper air lter
housing and then remove the upper housing and factory
intake tube.
6. Install the provided coupler (084055) onto the throttle
body and secure with the provided hose clamp.
7. Install the provided hump coupler (08639) onto the air
lter housing and secure with the provided hose clamp.

AIR-I40762A
REV 10/31/18
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions regarding t or instructions that are
not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing,
contact Airaid. The air lter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water.
WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air lter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
860-397 Airaid Oiled Media 861-397 Airaid SynthaMax Dry Media - Red
Synthamax Air Filters do not require oil. Service
air lter as needed by cleaning with common
non-petroleum all-purpose household cleaner
and water. Simple Green®, Formula 409® or
equivalent works great. Apply cleaner to outside of
air lter and allow to soak. Then ush lter clean
from the inside out with a garden hose and repeat
steps if necessary. Do not apply high pressure
water or air to clean lter. Allow lter to air dry
and reinstall.
Airaid. 1455 Citrus St., P.O. Box 1329, Riverside, CA. 92502 1-800-498-6951 [email protected] www.airaid.com
For your Oiled media lter we oer the
Airaid Tune Up Kit!
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
12. Double check your work!
Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.
Double check the hood clearance!
Reconnect the negative battery cable!
Continued...
8. Install the two provided quick disconnect vent ttings
into the AIRAID®intake tube as shown.
NOTE: Plastic NPT ttings are easy to cross thread.
Install the vent tting “hand” tight, then turn it two
complete turns with a wrench.
9. Install the provided AIRAID® air lter into the lower
air lter housing.
10. Assemble the AIRAID®intake tube and upper air
lter housing together loosely, then install the system
onto the throttle body and lower housing. Latch the
upper air lter housing into position and adjust the
intake tube for best t, then secure with the provided
hose clamps.
11. Connect the two vent lines to the quick disconnect
ttings installed into the intake tube and secure the
EVAP line to the insert on the bottom side of the tube.