Airaid 450-330 User manual

Installation Instructions
For Part Number:
450-330
2015-17 Ford Mustang 2.3l EcoBoost 4 Cyl.
ComponentIdentiication
1 AiraidPremiumFilter  1
2 AiraidIntakeTube   1
3TopPanel1
4BottomPanel1
5 FilterAdapter   1
6 Weatherstrip23"   1
7 ReducingCoupler   1
8HumpHose1
9 #40HoseClamp   1
10 #56HoseClamp   1
11 #68HoseClamp   2
12 AluminumFitting   1
13 #8FlatWasher   1
14 8‐32ButtonHead   1
15 13/16"IDGrommet   1
16O‐Ring1
17 ¼"‐20ButtonHead  4
18 1/4"FlatWasher   3
19 1/4‐20X1/2"LButtonHead 3
20Grommet1
21  ¼"LockWasher   4
22AiraidDecal1
1. Remove the battery box cover in the cowl and discon-
nect the negative battery terminal.
Full color instructions can be viewed on our web site at Airaid.com. If you need any assistance
please call 1-800-858-3333 to speak with a representative in our Customer Service Center before
returning the product.
2. Loosen the clamp on the intake tube and slide it off
of the airbox. Gently pry the harness anchor out of the
airbox and disconnect the air temp sensor.
Air temp sensor
Anchor
3. Remove the 6mm airbox mounting bolt in the inner
fender and lift the entire airbox assembly out of the vehi-
cle. Set the bolt aside for now. It is to be reused.
4. Be sure to retain speed clip in the inner fender . 5. Loosen the clamp on the turbo inlet coupler. 6. Disconnect the PCV and turbo bypass lines from the
intake tube and remove the tube from the vehicle.
9. Tilt the air temp sensor rearward so the locking tab
clears the ramp and rotate it counterclockwise 1/4 turn to
release it.
7. Insert the Grommet and Aluminum Fitting into the
Airaid Intake tube as shown. 8. Slide the Reducer and Clamps onto the turbo side of
the Intake Tube as shown. Leave the clamps loose for
now.
Fitting
Grommet
#40
#56
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION CON-
TROLLED MOTOR VEHICLE IN CALIFORNIA OR STATES
ADOPTING CALIFORNIA EMISSION PROCEDURES.
See AIRAID.COM for CARB status on each part for a specific vehicle.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.
12. Remove the protective film from the Panels and cre-
ate the assembly as shown using four 1/4 -20 Button
Head Screws and Lock washers.
REV.01.26.17
11. Insert the air temperature sensor into the Airaid intake
tube as shown and secure it using the #8 Screw and
Washer.
10. Replace the OEM O ring on the sensor with the sup-
plied Airaid O ring.
New
OLD
Lock Tab
14. Transfer the OEM air box grommet and anti-crush
sleeve into the Panel assembly as shown.
13. Install the Filter Adapter onto the Panel Assembly
as shown, using the three 1/4-20 Button Head Screws
and Flat Washers.
18 Lower the Airaid Intake tube down into position
and slide the reducer onto the turbo inlet.
19. Reconnect the PCV and bypass line to the Airaid
Intake Tube.
15. Remove the drivers side fan shroud bolt and set it
aside.
17. When properly installed, the Panel tab resides behind
the fan shroud as shown.
16. Install the Panel assembly into the engine compart-
ment as shown and secure using the OEM hardware
removed in steps 3and 15.
21. Slide the Airaid Intake Tube into the Hump Hose
and tighten all four Hose Clamps. Apply the Airaid
Bubble Decal onto the Intake Tube as shown.
20. Slide the Hump Hose with two, #68 Clamps onto the
Filter Adapter .
24. Double check your work. Make sure all clamps,
hoses, bolts, and screws are tight. Double check the
hood clearance. Reconnect the negative battery cable.
23. Install the Airaid Premium Filter onto the Filter
Adapter. Install the weatherstrip on top of the Panel as-
sembly as shown with the contour rolling away from the
filter.
22. Split one edge of the remaining Grommet with a
sharp knife and run the AT harness through it. Install
the Grommet and harness into the Panel as shown and
reconnect the sensor.
Cut
Airaid. 1815 West Crest Lane. Phoenix AZ 85027 [phone] [email protected] www.airaid.com
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION CON-
TROLLED MOTOR VEHICLE IN CALIFORNIA OR STATES
ADOPTING CALIFORNIA EMISSION PROCEDURES.
See AIRAID.COM for CARB status on each part for a specific vehicle.
AIR-I45330C