Airaid 400-758 User manual

AA
B
CD
F
F
H
G
D
FACTORY
PART
FACTORY
PART
E
I
Installation Instructions
400-758 860-397 Airaid Oiled Media Filter
401-758 861-397 SynthaMax Dry Media Filter - Red
Component Identication
2018 FORD F150 / F150 Raptor / Expedition
2018 LINCOLN Navigator
V6-3.5L
For Part Numbers:
Full color instructions can be viewed on our web site at Airaid.com. If you need any assistance please call 1-800-498-6951 to speak with
a representative in our Customer Service Center before returning the product.
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
1. Turn o the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories. Write
down all memory settings before disconnecting the
negative battery cable. Some radios will require
an anti-theft code to be entered after the battery is
reconnected. The anti-theft code is typically supplied
with your owner’s manual. In the event your vehicles
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles anti-
theft code.
TO START:
Description Qty. Part #
A HOSE CLAMP; #48 2 08601
B HOSE; 3"ID X 2"L REINFORCED 1 08711
C TUBE; INTAKE, 40%-758 1 KIT758A
D HOSE CLAMP; #60 2 08624
E HOSE; 3.75"ID X 2.25"L 1 08760
F HOSE CLAMP; #64 STAINLESS 2 08645
G HOSE; 4"ID X 2"L REINFORCED 1 08761
H AIR FILTER 1 860/861-397
I GROMMET; 1"OD,1/2"ID,1/2"THK 1 08064
2. Disconnect the inlet air temperature sensor electrical
connection.
3. Loosen the hose clamp that secures the factory intake
tube to the upper air lter housing.
4. Release the locking clamps, lift up the upper air
lter housing and then remove it from the vehicle, then
remove the factory air lter.
5. Loosen the two remaining hose clamps that secure
the factory intake tube to the turbo inlet tubes and then
remove the intake tube from the vehicle.
NOTE: AIRAID recommends that customers do not
discard factory air intake.
7. Install the provided coupler hose (08761) onto
the driver’s side turbo inlet tube and secure with the
provided hose clamp.

AIR-I40758
REV 11/06/18
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions regarding t or instructions that are
not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing,
contact Airaid. The air lter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water.
WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air lter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
860-397 Airaid Oiled Media 861-397 Airaid SynthaMax Dry Media - Red
Synthamax Air Filters do not require oil. Service
air lter as needed by cleaning with common
non-petroleum all-purpose household cleaner
and water. Simple Green®, Formula 409® or
equivalent works great. Apply cleaner to outside of
air lter and allow to soak. Then ush lter clean
from the inside out with a garden hose and repeat
steps if necessary. Do not apply high pressure
water or air to clean lter. Allow lter to air dry
and reinstall.
Airaid. 1455 Citrus St., P.O. Box 1329, Riverside, CA. 92502 1-800-498-6951 [email protected] www.airaid.com
For your Oiled media lter we oer the
Airaid Tune Up Kit!
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
16. Double check your work!
Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.
Double check the hood clearance!
Reconnect the negative battery cable!
Continued...
8. Install the provided coupler hose (08711) onto the
passenger side turbo inlet tube and secure with the
provided hose clamp.
9. Remove the inlet air temperature sensor from the
factory intake tube and remove the O-Ring from the
sensor.
NOTE: The inlet temperature sensor is very fragile,
use caution while handling the sensor.
10. Using the provided grommet, install the factory
inlet temperature sensor into the AIRAID intake tube as
shown.
NOTE: The inlet temperature sensor is very fragile,
use caution while handling the sensor.
11. Install the provided coupler (08760) onto the
AIRAID intake tube as shown and secure with the
provided hose clamp.
12. Install the AIRAID intake tube onto the turbo inlet
tubes and secure with the provided hose clamps.
13. Install the AIRAID air lter into the lower air lter
housing.
14. Reinstall the upper air lter housing onto the lower
housing and into the coupler on the intake tube. Secure
the housing to the lower housing with the factory clips
and to the intake tube with the provided hose clamp.
15. Reconnect the inlet air temperature sensor electrical
connection.