Alcolizer Druglizer LE5 User manual

REF: LE5 User Manual V3.docx Page 1 © Alcolizer Technology
LE5 User Manual
Disclaimer –External Documents note to reader
The BAC reading obtained by correct use of this device is only considered accurate at the time of testing.
Great care has been taken to ensure the accuracy of each reading.
Neither the manufacturer, the distributor, nor the owner accepts liability or responsibility due to any action
or claim arising from the reading produced by this device, whether used correctly or incorrectly.
External D
CHANGE STATUS
Version Number
Reason for Issue
Date
Authority
1.0
Initial Issue
1 Jun 2014
General Manager
1.1
New Template
20 Jan 2015
National Service
Manager
1.2
Revised template
Mar 2015
General Manager
V3
Revised template
Jan 2016
General Manager

REF: LE5 User Manual V3.docx Page 2 © Alcolizer Technology
Contents
1INTRODUCTION............................................................................................................4
2DESCRIPTION OF LE5.................................................................................................. 4
2.1 Equipment Overview .............................................................................................4
2.2 Device Overview....................................................................................................4
2.2.1 Test Key....................................................................................................5
2.2.2 LCD Colour Graphics Display....................................................................5
2.2.3 Mouthpiece Locator and Sample Inlet Spigot.............................................6
2.2.4 Up and Down Buttons................................................................................6
2.2.5 USB Port ...................................................................................................6
2.2.6 Battery Charger Port (Li-ION powered devices only) .................................6
2.2.7 AA Battery Compartment (Alkaline powered devices only) ........................6
3OPERATING INSTRUCTIONS....................................................................................... 6
3.1 General Information...............................................................................................6
3.2 Testing Types........................................................................................................7
3.3 Mouthpieces..........................................................................................................7
3.4 Charging the Battery (Li-ION powered device) ......................................................8
3.5 Changing the batteries (AA Alkaline powered device) ...........................................8
3.6 Turning On Device................................................................................................. 9
3.6.1 Mouthpiece Testing .................................................................................10
3.6.2 Taking a Mouthpiece (Active) Breath Sample..........................................11
3.6.3 Analysing a Mouthpiece Breath Sample ..................................................13
3.6.4 Passive Testing .......................................................................................14
3.6.5 Enabling Passive Standard......................................................................14
3.6.6 Taking a Passive Standard Breath Sample.............................................. 15
3.6.7 Analysing a Passive Breath Sample........................................................16
3.6.8 Enabling Passive Only.............................................................................17
3.6.9 Taking a Passive Only Breath Sample.....................................................17
3.7 Back operation ....................................................................................................18
3.8 Shutting Down.....................................................................................................18
4TEST OPTIONS MENU................................................................................................ 19
4.1 Test Cancel......................................................................................................... 19
4.2 Test Refusal........................................................................................................19
5GPS..............................................................................................................................20
5.1 Acquiring GPS satellites......................................................................................20
5.2 GPS Mode configuration......................................................................................21
5.3 Static GPS Mode Operations............................................................................... 21
5.4 Mobile GPS Mode Operations............................................................................. 22
6SENDING AND PRINTING DATA................................................................................23
6.1 Bluetooth Connection..........................................................................................23
6.2 Printer driver........................................................................................................25
6.2.1 Installing the printer driver........................................................................25
6.3 Connect Mode.....................................................................................................27
6.3.1 On Demand.............................................................................................27
6.3.2 Permanent...............................................................................................27

REF: LE5 User Manual V3.docx Page 3 © Alcolizer Technology
6.4 Auto Send............................................................................................................28
6.4.1 Auto Send Standard ................................................................................28
6.4.2 Auto Send Passive ..................................................................................28
6.5 Auto Print ............................................................................................................29
6.5.1 Auto Print Standard .................................................................................29
6.5.2 Auto Print Passive ...................................................................................30
6.6 Setting the Bluetooth printer PIN .........................................................................30
6.7 Printing records...................................................................................................31
6.7.1 Automatic printing....................................................................................31
6.7.2 Printing records .......................................................................................31
7AREA CODE................................................................................................................ 33
8RECORDS ...................................................................................................................34
8.1 Accessing Records.............................................................................................. 34
8.2 Clearing Records................................................................................................. 34
9CALIBRATION............................................................................................................. 35
9.1 Calibration alerts..................................................................................................35
9.2 Replacing sample module ...................................................................................36
10 SPECIFICATIONS........................................................................................................37
11 ALCOCONNECT.......................................................................................................... 37
11.1 Installing Alcoconnect Software...........................................................................37
11.2 Using Alcoconnect...............................................................................................39
11.2.1 Navigating around the Event Log page....................................................40
11.2.2 Set Log Settings (Filtering data)...............................................................41
11.2.3 Saving Event Logs................................................................................... 41
11.2.4 Erasing event logs or Clear log on device................................................42

REF: LE5 User Manual V3.docx Page 4 © Alcolizer Technology
1INTRODUCTION
This User Manual details the operation of the Alcolizer LE5 alcohol breath testing device and
Alcoconnect software for managing and analysing breath test results.
This User Manual is divided into various Sections and Sub-sections to enable the user to access the
required information with ease. It includes Cautions and Notes applicable to the LE5 device and a
Specifications table.
2DESCRIPTION OF LE5
2.1 Equipment Overview
The LE5 Equipment List includes the following items:
LE5 handheld device (Li-ION powered or AA Alkaline battery powered),
USB cable,
Battery Chargers (240VAC and 12VDC vehicle, Li-ION version only),
User Manual and Alcoconnect CD,
Silicon protective cover (optional) and wrist strap,
Carry bag or metal case (optional), and
Bluetooth printer (optional).
2.2 Device Overview
The LE5 is a handheld device consisting of a hard plastic outer case, optional silicon cover, wrist strap
and the following user displays, buttons and adaptor sockets (refer Figure 1):
a. Test Key,
b. LCD Colour Graphics Display,
c. Mouthpiece Locator and Sample Inlet Spigot,
d. Up and Down buttons,
e. USB Port, and
f. Battery Charging Port/AA Alkaline Battery Compartment (refer Figure 2)
NOTE
This User manual is applicable to the Alcolizer LE5 version S5MAPP installed with firmware version
1.26 and later.

REF: LE5 User Manual V3.docx Page 5 © Alcolizer Technology
Figure 1 –User Display, Buttons and Adapter Sockets
Figure 2 –Charging Port (left) and AA Battery Compartment (right)
2.2.1 Test Key
The Test Key activates selected functions.
2.2.2 LCD Colour Graphics Display
Displays the various functions of the device including:
g. Welcome screen which includes days remaining till next calibration( if activated);
h. Various Test modes (Mouthpiece, Passive Standard and Passive Only);
i. Extensive menus and options;
j. Ready notification;
k. Blow notification including progress bar;
Down Button
(d)
Test Key (a)
USB Port
(e)
Battery Charging Port/
AA Battery
Compartment
(f)
Up Button
(d)
Silicon Cover
LCD Colour
Graphics
Display (b)
Mouthpiece
spigot locator (c)
Wrist strap

REF: LE5 User Manual V3.docx Page 6 © Alcolizer Technology
l. BAC level in various formats;
m. GPS acquisition data;
n. Printer setup; and
o. Records information.
These and other displays are explained in the Operating Instructions Section.
2.2.3 Mouthpiece Locator and Sample Inlet Spigot
The disposable mouthpiece (sample tube) is located on the Mouthpiece Locator which surrounds the
Sample Inlet Spigot.
2.2.4 Up and Down Buttons
The Up and Down buttons allow access to various sub menus. Operation of both buttons also
facilitates access to the Off function (refer Section 3).
2.2.5 USB Port
The USB port facilitates connection of the device to a USB equipped computer using the cable included
with the device. Refer to Section 11 for instructions on using the Alcoconnect toolbox.
2.2.6 Battery Charger Port (Li-ION powered devices only)
The Battery Charging Port, installed only on the Li-ION powered devices, is located beneath a moisture
proof cap under the wrist strap bracket and facilitates connection to the battery chargers included
with the device.
2.2.7 AA Battery Compartment (Alkaline powered devices only)
The AA Alkaline battery compartment, installed only on the AA Alkaline powered devices, is located
beneath a dust proof cap adjacent to the wrist strap bracket. For access to the compartment refer to
paragraph 3.5.
3OPERATING INSTRUCTIONS
3.1 General Information
The following information should be observed when conducting breath test analysis using this device:
CAUTION
While the LE5 is a robust device, it does contain sensitive instrumentation and should not be
subject to rough handling or become submerged in water.
Do not store device in direct sunlight or places where extreme temperature conditions can occur.
NOTE
The LE5 has optional functions which may or may not be active on your device. The screen images
shown in this User Manual may differ to your device depending on the options fitted or functions
enabled.

REF: LE5 User Manual V3.docx Page 7 © Alcolizer Technology
p. To obtain an accurate reading, alcohol should not be consumed, or mouthwash
containing alcohol used for at least 15 minutes prior to using this device.
q. Blood Alcohol Concentration (BAC) readings can continue to rise or fluctuate for up to
two hours after alcohol was last consumed. Should the BAC readings be near or over
the local threshold, drinking should cease, then a re-test conducted after 15 minutes.
r. Driving or operating machinery should not occur until a new test shows a decline in
BAC reading and the BAC reading is below the local legislation legal limit.
s. It can take up to one hour for the average person’s system to absorb a 0.01 BAC before
the level returns to zero. In such circumstances further testing later in the day or the
following morning is strongly recommended.
3.2 Testing Types
The LE5 can perform both Mouthpiece and Passive (Passive Standard and Passive Only) testing.
Mouthpiece testing provides a BAC reading in g/100ml (or other formats as required) and Passive
testing will display the presence of alcohol in breath. Following a Passive test that indicates the
presence of alcohol, a Mouthpiece test should then be performed if an accurate BAC is required.
3.3 Mouthpieces
There are two types of Mouthpieces available for use on the LE5 (refer Figure 3). These are the:
Spit Trap Non Return Valve Mouthpiece (2 variants), and
Standard Spigot Locator Mouthpiece.

Figure 3 –Mouthpiece Types
NOTE
Mouthpiece testing is also referred to as Standard or Active testing.
Non ribbed end
Sample inlet
ports
Standard
mouthpiece
Non return
spit trap
mouthpieces
Ribbed
end

REF: LE5 User Manual V3.docx Page 8 © Alcolizer Technology
The advantage of using the spit trap type mouthpieces is that most of the saliva in the exhaled breath
is collected in the mouthpiece and does not enter the device.
3.4 Charging the Battery (Li-ION powered device)
Prior to initial use, the LE5 battery should be fully charged. The battery charge cycle may take up to
two hours.
Charge the battery as follows:
t. Connect the charger DC socket to the LE5 battery charging port (refer Figure 1).
u. Connect the AC or DC (vehicle) plug to a suitable power supply and switch on power.
The device will automatically start and Charging will be displayed.
When the battery is fully charged, the battery condition indicator on the LCD Colour Graphics Display
will display five bars (refer Figure 4).
Figure 4 –Battery Condition Indicator
Recharge the battery when the battery condition indicator shows one bar to ensure testing will not
be interrupted by a flat battery.
3.5 Changing the batteries (AA Alkaline powered device)
Prior to initial use, the LE5 batteries should be new. Alcolizer recommend the use of Eveready® AA
Alkaline EN91 batteries for the LE5. Change the batteries in accordance with the following procedures
(refer Figure 5):
CAUTION
The battery in the LE5 device is a Li-ION battery. As such it should not be tampered with in
anyway. Should any problems occur that are related to the battery, contact your local Alcolizer
representative for advice.
Only use the battery charger supplied with the Alcolizer supplied equipment. Use of non Alcolizer
battery chargers could damage the device and render it inoperative.
Note
The device cannot be used for testing during charging but can be used for accessing Records
(refer Section 8).

REF: LE5 User Manual V3.docx Page 9 © Alcolizer Technology
v. Invert the device so the compartment hatch is upper most (refer Figure 5a).
w. Access the battery compartment by pressing the compartment release button on the
underside of the device (refer Figure 5a). The compartment hatch will pop out.
x. Open the hatch by gently moving it to expose the compartment (refer Figure 5b).
y. Remove the flat batteries and insert two new batteries ensuring the polarity is correct.
Polarity markings (o and +) are marked on the hatch contactor (refer Figure 5b).
z. Close the hatch by gently positioning it in place and pressing it closed (refer Figure 5c).
A click indicates the hatch is locked.
Figure 5 –Installing/Replacing AA Alkaline Batteries
3.6 Turning On Device
Turn the device on as follows:
aa. Press either the Test key or Up/down buttons. A company logo screen will appear for
a period of five seconds prior to the test screen displaying. The logo screen can be
terminated sooner by pressing either the Test key or Up/down buttons a second time.
Note
If the device has a silicon cover installed, the release button is operatable by pressing the raised
portion over the button on the back of the device. Removal of the cover is not required to change
the batteries.
Note
On specially configured devices, additional information may be displayed on start-up e.g. Device
serial number, Sample module serial number and days till calibration.
To permanently display this information, hold the Test key down for an extended period upon
start up.
Compartment
hatch
Release
button
Hatch
open
Hatch
contactor
a
b
c
Closing
hatch

REF: LE5 User Manual V3.docx Page 10 © Alcolizer Technology
bb. The Display will show press to test (refer Figure 6).
Figure 6 –Press to test message
3.6.1 Mouthpiece Testing
Attach the mouthpiece to the device as follows:
cc. Grasp the mouthpiece at the non-ribbed end and tear the plastic wrapping from the
ribbed end, downwards to expose the sample inlet hole.
dd. Locate the mouthpiece sample inlet port over the mouthpiece locator in line with the
recesses that surround the spigot (refer Figure 7).
ee. Press the mouthpiece sample inlet port onto the locator until it is attached securely
(refer Figure 8). The orientation of the mouthpiece will not affect the sampling.
ff. Remove the remaining portion of the plastic wrap just prior to testing to ensure
hygienic use.
Figure 7 –Locating the Mouthpiece
CAUTION
To maintain a healthy sampling environment, the following procedures must be strictly adhered
to.

REF: LE5 User Manual V3.docx Page 11 © Alcolizer Technology
Figure 8 –Mouthpiece correctly positioned
3.6.2 Taking a Mouthpiece (Active) Breath Sample
Perform a Mouthpiece Test as follows:
gg. Press the Test key. The device will perform a self-test and Please wait... and a progress
bar will be displayed.
hh. BLOW will be displayed when the device is ready (refer Figure 9).
Figure 9 –Blow is displayed when device is ready
ii. After taking a deep breath, the test subject places their mouth over mouthpiece inlet
(ribbed end) and blows a gentle to medium breath sample into the mouth piece (refer
Figure 10).
Note
Before taking a breath sample, ensure the subject has not consumed alcohol for at least 15
minutes.
If any step in a breath test sequence is not completed or the device is left idle for a prolonged
period of time, then the device will terminate the breath test and display Test timed out. The
device will return to the press to test display
The standard breath test time out period is 60 seconds. If a test time out does occur during a
breath test, a new breath test must be performed.
Note
If the self-check is unsuccessful an error code will be displayed and the device will not accept a
breath sample.

REF: LE5 User Manual V3.docx Page 12 © Alcolizer Technology
Figure 10 –Providing a sample
jj. The exhaled breath volume is indicated via a bar graph; scrolling left to right at the
bottom the screen and a graph showing air flow over time in seconds (refer Figure 11).
A beeping sound is also heard during the breath sample delivery phase, indicating a
satisfactory breath sample is being delivered.
Figure 11 –Sample progress bar
kk. The test subject continues blowing until the device takes a sample of the exhaled
breath volume, indicated by a click and long beep sound.
The frequency of the sound beeps increases with the intensity of the blow pressure. Blowing too hard
or too soft will result in Invalid Sample Try Again being displayed (refer Figure 12). The device will
return to the Blow screen so another sample can be taken.

REF: LE5 User Manual V3.docx Page 13 © Alcolizer Technology
Figure 12 –Invalid Sample try Again message
3.6.3 Analysing a Mouthpiece Breath Sample
After a valid breath sample is taken, the Analysing Sample message is displayed until the device
calculates the BAC reading. This will normally take a few seconds. In cold climate conditions it may
take longer to display the BAC reading (refer Figure 13).
Figure 13 –Analysing sample message
When the BAC reading is calculated, it will be displayed on the screen together with unit of
measurement (e.g. g/100ml, g/210L) and be retained until the Recovering period has ended. The
screen colour will vary depending on the percentage of alcohol present; green for zero, orange for
zero to 0.049 g/100ml, g/210L and red for readings greater than 0.05 g/100ml, g/210L. The Recovering
period is indicated by Recovering shown on the display (refer Figure 14).

REF: LE5 User Manual V3.docx Page 14 © Alcolizer Technology
Figure 14 –Various BAC and screen colours displayed
The Recovering period is the time the fuel cell sensor requires to recover from the previous breath
test. This period will vary according to BAC readings displayed, longer for higher readings.
Remove the used mouthpiece by rotating it. It will come away from the spigot easily. Dispose of
mouthpieces in a responsible manner.
To perform another breath test, repeat the steps in paragraph 3.6.1.
3.6.4 Passive Testing
Passive testing is a test that is performed in a non-invasive manner and without using mouthpieces.
The LE5 can perform two types of Passive testing. These are Passive Standard and Passive Only.
All Passive testing is performed by holding the device approximately 80mm to 100mm in front of the
test subject’s mouth and asking them to count or talk so that exhaled breath may be picked up by the
device and analysed for the presence of any alcohol.
When using Passive Standard testing, a Mouthpiece test is automatically enabled should the device
detect alcohol on the subject’s exhaled breath. Passive Only testing does not prompt the user for
further testing.
3.6.5 Enabling Passive Standard
If Passive standard mode has not been enabled, proceed as follows:
ll. With the screen displaying press to test, press the Up and Down buttons
simultaneously. The User Menu will be displayed.
mm. Press the down button to scroll down to Test Type (refer Figure 15).
Figure 15 –Test Type displayed

REF: LE5 User Manual V3.docx Page 15 © Alcolizer Technology
nn. Press the Test key until Passive Std is displayed (refer Figure 16).
oo.
Figure 16 –Passive Standard displayed
pp. Press the Up and Down buttons simultaneously. Passive Standard is now enabled or
press the Down button until Back is highlighted then press the Test key to leave the
User Menu.
3.6.6 Taking a Passive Standard Breath Sample
Perform a Passive Standard test as follows:
qq. On the press passive test page, press the Test key. Ready for passive Test is displayed
(refer Figure 17).
Figure 17 –Ready for passive test message
rr. Press the Test button. The device will perform a self-test and then return to Ready for
passive Test.
Note
If any step in a breath test sequence is not completed or the device is left idle for a prolonged
period of time, then the device will terminate the breath test and display Test timed out the device
will return to the press passive test display.
The standard breath test time out period is 60 seconds. If a test time out does occur during a
breath test, a new breath test must be performed. Press the Test key to perform a new passive
breath test as per steps above.

REF: LE5 User Manual V3.docx Page 16 © Alcolizer Technology
ss. Hold the device no further than 100mm in front of the test subject’s mouth; so that
the subject is breathing or talking directly into the device’s sample inlet port (refer
Figure 18).
Figure 18 –Providing a Passive sample
tt. Ask the Subject to start counting from 20 onwards a one second rhythm, until you tell
them to stop, “20…21…22…23…24…25…etc.”
uu. Press the Test button while subject is counting. The device will make a series of clicking
sounds as the sample is being taken.
The device is set to take three pump samples. During these three pumps the operator must hold the
device steady and at the same distance from the subject. The device will give three sample pump
clicks, followed by a long beep sound. Analysing Sample will then be displayed (refer Figure 13).
3.6.7 Analysing a Passive Breath Sample
After a valid breath sample is taken, the Analysing Sample message is displayed until the device
determines if alcohol is present. This will normally take a few seconds. In cold climate conditions it
may take longer to display the result.
When the Passive standard reading is calculated, it will be displayed and retained until the Recovering
period has ended.
If a Pass No Alcohol reading is displayed the device has indicated that no alcohol was detected in the
near vicinity of subject’s exhaled breath. When the Recovering period has ended the device is ready
for next Passive standard breath test (refer Figure 19).
Figure 19 –Pass No Alcohol message
To perform another Passive standard breath test, repeat steps in paragraph 3.6.4.
If a Warning Alcohol Present reading is displayed the device has indicated that alcohol was detected
in the near vicinity of subject’s exhaled breath (refer Figure 20).

REF: LE5 User Manual V3.docx Page 17 © Alcolizer Technology
Figure 20 –Warning Alcohol Present message
After the recovery period has ended, the device is enabled automatically to take an Active
(Mouthpiece) sample (refer Figure 21). Perform an Active test in accordance with the procedures in
paragraph 3.6.1.
Figure 21 –Warning Alcohol Present/Press for Active Test display
3.6.8 Enabling Passive Only
To enable Passive Only, perform the same steps as in paragraph 3.6.5 with the exception of step
3.6.5.c. Press the Test key until Passive Only is displayed.
3.6.9 Taking a Passive Only Breath Sample
The procedures for performing a Passive Only test are the same as those for performing a Passive
Standard test (refer paragraph 3.6.6).
Note
A Passive Only test will not automatically enable an Active (Mouthpiece) test the same way a
Passive Standard test does.

REF: LE5 User Manual V3.docx Page 18 © Alcolizer Technology
3.7 Back operation
The user menus include a Back selection which when selected will return to the previous screen. To
select Back, proceed as follows:
vv. Press the Up/down buttons until Back is highlighted (refer Figure 22).
Figure 22 –Screen Back selection
ww. Press the Test key. The display will return to the previous screen.
3.8 Shutting Down
The LE5 will automatically shut down after a period of inactivity. Should the device be required to be
shut down manually (e.g. to conserve battery life), perform the following procedures:
xx. With the screen displaying press to test, Press the Up and Down buttons
simultaneously. The User Menu will be displayed (refer Figure 15).
yy. Using the down button, scroll down to off (refer Figure 23).
Figure 23 –Off displayed
Note
When a Warning Alcohol Present reading is displayed after performing a Passive Only test, it is
strongly recommended that a Mouthpiece Breath Test be performed, after the recovery period has
ended (refer paragraph 3.6.2).

REF: LE5 User Manual V3.docx Page 19 © Alcolizer Technology
zz. Press the Test key. The device will turn off.
To further conserve battery life, the device will automatically switch off the display back light after
two minutes. To re-activate the device following back light power down, Press the Test key or
Up/down buttons. The device will display the last screen that was activated at the time the back light
switched off.
4TEST OPTIONS MENU
4.1 Test Cancel
If the user wishes to cancel a test, perform the following steps:
aaa. With the Blow screen displayed, Press the Up and Down buttons simultaneously. The
Test Options Menu and Test Cancel is displayed (refer Figure 24).
Figure 24 –Test Options Menu and Test Cancel
bbb. Press the Test key. The screen will return to the press to test display.
4.2 Test Refusal
If a test is refused, the user can activate the Test Refuse option as follows:
ccc. With the Blow screen displayed, press the Up and Down buttons simultaneously. The
Test Options Menu and Test Cancel is displayed (refer Figure 24).
ddd. Press the Down button to highlight Test Refuse (refer Figure 25).
Figure 25 –Test Refuse displayed

REF: LE5 User Manual V3.docx Page 20 © Alcolizer Technology
eee. Press the Test key. The device will beep rapidly for one second and Test Refused will
be displayed flashing momentarily (refer Figure 26). The screen will then return to the
press to test display. The test refusal will be recorded in Records.
Figure 26 –Test Refused displayed
5GPS
The Global Positioning System (GPS) function (if installed) enables the exact location of the device to
be known and under certain circumstances, the location of testing to be recorded. Two GPS mode
functions are available: Mobile and Static.
5.1 Acquiring GPS satellites
To acquire GPS satellites, perform the following steps:
fff. With the screen displaying press to test, Press the Up and Down buttons
simultaneously. The User Menu will be displayed (refer Figure 15).
ggg. Press the Down button to highlight GPS (refer Figure 27).
Figure 27 –GPS displayed
hhh. Press the Test key. The GPS acquisition screen will be displayed.
NOTE
Depending on the specific configuration of the device, the GPS functions are either enabled or disabled.
These functions are generally enabled as a Customer requirement by Alcolizer Technology. Should the
device in use require the enabling of certain GPS functionality, contact Alcolizer Technology for further
advice.
Test
Refused