Allen-Bradley PowerFlex 700 AFE User manual

PowerFlex 700AFE to PowerFlex 755TM Regenerative
Bus Supply
Catalog Numbers 20Y, 20J
Migration Guide
Original Instructions

Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to
familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,
and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are
required to be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may
be impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from
the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Labels may also be on or inside the equipment to provide specific precautions.
WARNING: Identifies information aboutpractices or circumstances that can cause an explosion in a hazardous
environment, which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT Identifies information that iscritical for successful application and understanding of the product.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURNHAZARD:Labels may be onor inside theequipment, for example, adriveormotor,toalert peoplethatsurfacesmay
reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potentialArcFlash.ArcFlashwillcausesevereinjury or death. WearproperPersonalProtectiveEquipment(PPE).FollowALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 3
TableofContents
Preface
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Parameter References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Compatibility Quick Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before Migration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 1
Selection Considerations About the PowerFlex 700AFE Bus Supply. . . . . . . . . . . . . . . . . . . . . . . 14
PowerFlex 700AFE Catalog Number Explanation. . . . . . . . . . . . 15
About the PowerFlex 755TM Bus Supply . . . . . . . . . . . . . . . . . . . . . . . 16
PowerFlex 755T Product Catalog Number Explanation . . . . . . 17
Power and Control Bus Bar Ratings. . . . . . . . . . . . . . . . . . . . . . . . . 20
Power Source Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Sizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Other Loads Powered from the AFE AC Power Source . . . . . . . 22
Power Source Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Recommended Grounding Scheme . . . . . . . . . . . . . . . . . . . . . . . . . 24
Bus Capacitance and Precharging Consideration. . . . . . . . . . . . . . . . . 24
EMI Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Power Filter Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Circuit Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
External Circuit Protection Device Compatibility
Check Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
AC Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Other Power Circuit Considerations. . . . . . . . . . . . . . . . . . . . . . . . 29
Control Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specification and Feature Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Cross Reference Guides. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Dimensional Cross Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Device Ports and Main Control Board I/O . . . . . . . . . . . . . . . . . . . . . . 50
PowerFlex 700AFE Bus Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
PowerFlex 755TM Bus Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Hardware Enable Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Customer Power Terminal Comparison . . . . . . . . . . . . . . . . . . . . . . . . 56
PowerFlex 700AFE Bus Supply Customer Power Terminal
Locations and Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
PowerFlex 755TM Bus Supply Customer Power Terminal
Locations and Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Control Terminal Comparison. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
PowerFlex 700AFE Digital and Analog I/O . . . . . . . . . . . . . . . . . 64
PowerFlex 755TM Bus Supply I/O Option Modules . . . . . . . . . 65

4Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Table of Contents
Chapter 2
Bus Supply Hardware and
Parameter Conversion Configuration Software and HIM Versions . . . . . . . . . . . . . . . . . . . . . 67
Parameter Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
PowerFlex 700AFE Parameter Assignment . . . . . . . . . . . . . . . . . . 68
PowerFlex 755T with TotalFORCE Control Parameter
Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Bus Supply Hardware Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
PowerFlex 700AFE Bus Supply Control Devices . . . . . . . . . . . . . 72
PowerFlex 755TM Bus Supply Control . . . . . . . . . . . . . . . . . . . . . 75
Chapter 3
Communication Configuration PowerFlex 755T 20-COMM-x Network Adapter
Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Scaling of Reference and Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . 81
PowerFlex 700AFE DPI Communications . . . . . . . . . . . . . . . . . . 81
PowerFlex 755TM Bus Supply Communications . . . . . . . . . . . . 82
Logic Command Word Comparison. . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Datalink Handling Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
16-bit Processors (PLC-5, SLC 500, and
MicroLogix 1100/1400) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Appendix A
Enclosure Information Dimension and Enclosure Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Cooling and Airflow Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
PowerFlex 700AFE Installation Requirements . . . . . . . . . . . . . . . 90
PowerFlex 755TM Bus Supply Installation Requirements. . . . . 95
PowerFlex 755T Product Equipment Handling Options . . . . . . . . . 99
Module Service Cart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
DC Precharge Module Service Lift . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Power Module Service Ramp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Power and Filter Module Storage Hardware . . . . . . . . . . . . . . . . . 99
IP00 Open Type Power Structures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 5
Preface
The purpose of this migration guide is to assist you in migrating a
PowerFlex® 700AFE active front end to a PowerFlex 755TM regenerative bus
supply. Use this migration guide to help you understand some basic migration
requirements.
This document provides basic guidelines for migrating to the
PowerFlex 755TM bus supply. To help you determine the proper migration
solution, review the associated product literature to understand the technical
similarities and differences between the PowerFlex 700AFE and the PowerFlex
755TM bus supplies.
Download the installation instructions, technical data, programming, and
wiring manuals listed in Additional Resources on page 10.
Many sections of this migration guide direct you to additional details and
information available in these publications.
Overview This publication contains these three chapters:
Chapter 1: Selection Considerations on page 13.
This chapter compares the specifications, features, dimensions, and power and
control terminals of the PowerFlex 700AFE with the PowerFlex 755TM bus
supply.
Chapter 2: Bus Supply Hardware and Parameter Conversion on page 67.
This chapter provides comparisons of the electrical configuration, control
wiring, and parameters of the PowerFlex 700AFE with the PowerFlex 755TM
bus supply.
Chapter 3: Communication Configuration on page 79.
This chapter identifies the network options that can be migrated to the
PowerFlex 755TM bus supply. This section also provides overview
information for reference/feedback scaling, and using I/O adapters and 16-bit
processors (PLC-5®).
IMPORTANT Throughoutthis publication,thetermPowerFlex755Tis usedtodescribethe
entire family of PowerFlex 755T TotalFORCE® AC drives including 755TM bus
supplies. Where there is a notable difference, the specific suffix letters are
indicated.
Theterms'bus supply'and 'lineside converter'areboth usedto describethe
active front end converter in the PowerFlex 755TM bus supplies.

6Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Preface
Parameter References PowerFlex 700AFE parameters are referenced in the format Pxxx [name], By,
where:
•xxx is the parameter number
•[name] is the parameter display name
•yis the bit number (if applicable)
In this document, PowerFlex 755T ports, parameters, and bits are referenced in
the format #:x.y [name], where:
•#istheportnumber
• x is the parameter number
• [name] is the parameter display name
• y is the bit number (if applicable).
General Precautions Be aware of the following general precautions when working with this type of
equipment. See the installation instructions for each bus supply for additional
product-specific precautions. Applicable publication information canbe found
in Additional Resources on page 10.
EXAMPLE For example; referencing an I/O module that is installed in port 4,
parameter 6 [Dig Out Invert], bit 1 (TransOut0) can be shown as 04:0006.01
[Dig Out Invert].
The leading zeroes and [name] can be omitted unless required to clarify the
context.
This parametercan also be shown as 4:6.1, 4:6.01 [Dig Out Invert] or any
other combination that shows the minimum port:parameter information.
ATTENTION: Only qualified personnel familiar with adjustable frequency AC
drives and associated machinery should plan or implement the installation,
startup, and subsequent maintenance of the system. Failure to comply can
result in personal injury and/or equipment change.
ATTENTION: This drive contains ESD (Electrostatic Discharge) sensitive parts
and assemblies. Static control precautions are required when installing,
testing, servicing or repairing this assembly. Component damage may result
if ESD control procedures are not followed. If you are not familiar with static
control procedures, reference Guarding Against Electrostatic Damage,
publication 8000-4.5.2 or any other applicable ESD protection handbook.

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 7
Preface
Compatibility Quick Check Use the following comparison table to confirm that there are compatible
PowerFlex 755TM bus supplies available to migrate from your existing
PowerFlex 700AFE bus supply. If the existing PowerFlex 700AFE installation
configuration does not have any of these exceptions, proceed to use the
guidelines in this document.
If the existing PowerFlex 700AFE bus supply has any of the above
configuration exceptions, contact an Authorized Rockwell Automation
Distributor specialist, Solution Partner, Recognized System Integrator, or
Rockwell Automation account manager to discuss engineered solutions for
custom migrations.
Follow this link for a list of Solution Partners and Recognized System
Integrators: http://www.software.rockwell.com/corporate/sp/
RASISearchResults.cfm?Programlevel=SP.
Table 1 - Comparison Quick Check Considerations
Consideration If you have these existing PowerFlex
700AFE Configuration Exceptions Then follow these recommendations for the PowerFlex 755TM Bus Supply
migration
Maximum DC bus
current and power
output
More than2 x frame 13 AFE bus supplies in
parallel. When this migration guide was published there were no compatible units available.
Future product enhancements may expand
the range of migration solutions.
Mixed Frame Sizes Any combination of frame 10 and frame 13
AFE converters in parallel. Mixed frame parallel migration solutions are not covered in this migration guide. A
custom migration solution may be
required.
Custom Packaging IP00 open type units that are installed in non-
standard enclosures. Open type IP00 PowerFlex 755TM Bus Supplies are available. IP00 conversions are
not covered in this migration guide. A
custom migration solution may be
required.
Parallel non-
regenerative bus
supply
Any system with anAFE in parallel witha
non-regenerative converter (diode or SCR
rectifier). Themost common configuration
was an AFEin parallelwith PowerFlex SCR
converter(s).
ThePowerFlex755TMBusSupplycannotbe
combined inparallelwith any other bus
supply converters.
Integration with
common DC bus
drive system lineup
DC bus bars, control bus bars integrated
between the AFE and common bus inverter
drive enclosures.
This configuration can be migrated to
PowerFlex755TMbussupply,however, this
solution is not covered in this migration
guide.
The IP21/IP54 enclosed PowerFlex 755TM
bus supply converter bus bar configuration
is not mechanically compatible with any
existing PowerFlex 700AFE configurations
and may require a custom migration
solution with transition cell enclosure(s).
Communication
Protocol ControlNet Fiber
BACnetIP
HVAC Modbus RTU
CANopen
Interbus
LonWorks
Modbus/TCP
Remote I/O
RS485 DF1
These communication protocols are not
supported by the PowerFlex 755T product.
A custom migration solution and/or an
externalcommunicationprotocolconverter
may be required.

8Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Preface
Before Migration Follow these best practices to be sure that your migration is successful.
• Upload and save the PowerFlex 700AFE parameters via Connected
Components Workbench™, Studio 5000 Logix Designer®, or
DriveExecutive™ software. If you cannot connect to the drive online,
manually record the parameter values.
• Record and label all power, digital, and analog I/O control wiring.
• Upload and save any network files and programmable logic controller
(PLC) programs.
General Information
See the Wiring and Grounding Guidelines for Pulse-width Modulated
(PWM) AC Drives Installation Instructions, publication DRIVES-IN001, for
information regarding the topics listed below.
Wire/cable type
• General
•Inputpower
• Discrete drive I/O
• Analog signal and encoder
• Communication
Power distribution
• System configurations
•AClinevoltage
• Surge protection MOVs and common mode capacitors
• AC line impedance
• PowerFlex drives used with regenerative units
• DC bus wiring guidelines
Grounding
•Safetygrounds
• Noise-related grounds
Installation practices
•Mounting
•Conduitentry
•Groundconnections
• Wire routing
•Conduit
• Cable trays
•Shieldtermination
•Conductortermination
•Moisture

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 9
Preface
Electromagnetic interference
• Causes and containing common mode noise
• Causes and preventing/mitigating transient interference
•Enclosurelighting
Abbreviations This table contains abbreviations that are used throughout this document.
Abbreviation Description
(o) Optional equipment
(s) Standard, or included in base catalog number
AFE Active Front End
AIC Ampere Interrupting Current
AOP Add On Profile
CBI Common Bus Inverter
EMI Electromagnetic Interference Filter
HD Heavy Duty Overload Rating
HIM Human Interface Module
I/O Input/Output
LD Light Duty Overload Rating
LSC Line Side Converter
MCC Motor Control Center
MOV Metal Oxide Varistor
ND Normal Duty Overload Rating
PLC Programmable Logic Controller
PWM Pulse-width Modulated
SCCR Short Circuit Current Rating
TVSS Transient Voltage Surge Suppressor
VFD Variable Frequency Drive
XLPE Cross-linked Polyethylene

10 Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Preface
Additional Resources These documents contain additional information concerning related products
from Rockwell Automation.
Resource Description
PowerFlex Active Front End UserManual, publication 20Y-
UM001 Provides basic information that is needed to install, start-up, and troubleshooting of IP20/IP21 enclosed
PowerFlex 700AFE bus supplies.
Provides detailed technical data, specifications,
ratings, andoption information.
Provides detailed parameter descriptions,
configuration settings, and fault/alarm
troubleshooting.
Lifting and Mounting PowerFlex Active Front End (AFE) –
Frames 10 and 13 Installation Instructions,
publication 20Y-IN001
Provides detailed installation instructions for
handling IP20/IP21 enclosed PowerFlex 700AFE bus
supplies.
PowerFlex 700AFE Firmware v1.003 Release Notes,
publication 20Y-RN001 Firmware Release Notes for PowerFlex 700AFE bus
supply.
PowerFlex Active Front End Solutions Product Profile,
publication 20Y-PP001 Provides an overview of product benefits and features.
PowerFlex Active Front End – Frame 10 Hardware Service
Manual, publication 20Y-TG001 This manual contains hardware service information for the frame 10 PowerFlex Active Front End.
PowerFlex Active Front End – Frame 13 Hardware Service
Manual, publication 20Y-TG002 This manual contains hardware service information
for the frame 13 PowerFlex Active Front End.
PowerFlex Active Front End in IP202500MCCStyleEncl. Fr.
10 Bus Splice Kit Installation Instructions,
publication 20Y-IN003
Providesdetailedinstallationinstructionsfor MCCbus
splice kit.
PowerFlex Active Front End in IP202500MCCStyleEncl. Fr.
13 Right-Side Bus Splice Kit Installation Instructions,
publication 20Y-IN004
Providesdetailedinstallationinstructionsfor MCCbus
splice kit.
PowerFlex Active Front End in IP202500MCCStyleEncl. Fr.
13 Left-Side Bus Splice Kit Installation Instructions,
publication 20Y-IN005
Providesdetailedinstallationinstructionsfor MCCbus
splice kit.
PowerFlex 700AFE Spare Parts Installation Instructions,
publication 20Y-IN002 Provides detailed installation instructions for PowerFlex 700AFE spare parts.
PowerFlex 700H, 700S, and 700AFE Drive Fan Systems,
Frames9…14 Installation Instructions,
publication PFLEX-IN029
Provides detailed installation instructions for cooling
fan replacement and installation.
Balancing Resistor Kit for 600/690V Frame 13 PowerFlex
700AFE and 600/690V Frame 13 and 14 PowerFlex 700H/
700S AC Drives Installation Instructions, publication
PFLEX-IN028
Provides detailed installation instructions for
balancing resistor replacement.
PowerFlex 750-Series Products with TotalFORCE Control
Technical Data, publication 750-TD100 Provides detailed technical data, specifications, ratings, fuse/circuit breaker sizing and option
information for IP20/IP54 enclosed PowerFlex 755T
products.
PowerFlex 750-Series Products with TotalFORCE Control
Installation Instructions, publication 750-IN100 Provides procedures for the handling, installation, andelectrical wiringof IP20/IP54enclosedPowerFlex
755T products.
PowerFlex 755TM IP00 Open Type Kits Technical Data,
publication 750-TD101 Provides detailed technical data, specifications,
ratings, fuse/circuit breaker sizing and option
information for IP00 open type PowerFlex 755T drive
system products.
PowerFlex 755TM IP00 Open Type Kits Installation
Instructions, publication 750-IN101 Provides procedures for the handling, installation, and electrical wiring of IP00 open type PowerFlex
755T drive system products.
PowerFlex Drives with TotalFORCE Control Programming
Manual, publication 750-PM100 Provides detailed parameter descriptions, configuration settings, and fault/alarm
troubleshooting.

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 11
Preface
PowerFlex 750-Series Products with TotalFORCE Control
Hardware Service Manual, publication 750-TG100 Provides detailed troubleshooting, maintenance, componenttesting,and hardwareserviceinstructions
for PowerFlex 750T drives and bus supplies.
Drives in Common Bus Configurationswith PowerFlex
755TM Bus Supplies Application Techniques,
publication DRIVES-AT005
Provides basic information to properly wire and
ground the following products in common bus
applications:
• PowerFlex 755TM drive system products for
common bus solutions
• PowerFlex 750-Series AC and DC input drives
• Kinetix 5700 servo drives
PowerFlex 755 Drive Embedded EtherNet/IP Adapter User
Manual, publication 750COM-UM001 Thesepublicationsprovidedetailedinformationonto configure, use, and troubleshoot PowerFlex 750-
Series communication option modules and adapters.
PowerFlex 20-750-DNET DeviceNet Option Module User
Manual, publication 750COM-UM002
PowerFlex 20-750-CNETC Coaxial ControlNet Option
Module, publication 750COM-UM003
PowerFlex 20-750-PBUS Profibus DPV1 Option Module,
publication 750COM-UM004
PowerFlex 20-750-BNETIP BACnet/IP Option Module,
publication 750COM-UM005
PowerFlex 20-750-PNET Profinet Single-port Option
Module User Manual, publication 750COM-UM006
PowerFlex 20-750-PNET2P Profinet Dual-port Option
Module, publication 750COM-UM007
PowerFlex 20-750-ENETR Dual-port EtherNet/IP Option
Module User Manual, publication 750COM-UM008
PowerFlex 750-Series Drives with TotalFORCE Control
Built-in EtherNet/IP Adapter User Manual, publication
750COM-UM009
PowerFlex 20-HIM-A6 and 20-HIM-C6S HIM (Human
Interface Module) User Manual, publication 20HIM-
UM001
ProvidesdetailedinformationontheHumanInterface
Module (HIM).
PowerFlex 755TM DC Precharge Modules Unpacking and
Lifting Installation Instructions, publication 750-IN103 Provides detailed set-up and operating instructions
for the DC precharge module lift.
PowerFlex 750-Series Service Cart and DCPC Module Lift
Installation Instructions, publication750-IN105 Provides detailed set-up and operating instructions for the module service cart and lift extension option.
PowerFlex 755TM Power and Filter Module Storage
Hardware Installation Instructions, publication 750-IN106 Provides detailed installation and usage instructions for this hardware accessory.
PowerFlex 755T Module Service Ramp Installation
Instructions, publication 750-IN108 Provides detailed usage instructions for the module
service ramp.
PowerFlex 750-Series ATEX Option Module user manual,
publication 750-UM003 Provides information on using the 20-750-ATEX option module.
Wiring and Grounding Guidelines for Pulse-width
Modulated (PWM) AC Drives Installation Instructions,
publication DRIVES-IN001
Provides detailed installation guidelines and
recommendations for PWM AC drive equipment.
Industry Installation Guidelines for Pulse Width
Modulated (PWM) AC Drives, publication DRIVES-AT003 Provides basic information on enclosure systems,
considerations to help protect against environmental
contaminants, and power and grounding
considerations for installing Pulse Width Modulated
(PWM) AC drives.
Industrial AutomationWiring and Grounding Guidelines,
publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.
Resource Description

12 Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Preface
You can view or download publications at
http://www.rockwellautomation.com/global/literature-library/overview.page.
To order paper copies of technical documentation, contact your local
Allen-Bradley distributor or Rockwell Automation sales representative.
Safety Guidelines for the Application, Installation, and
Maintenance of Solid-State Control, publication SGI-1.1
Provides general guidelines for the application,
installation, and maintenance of solid-state control.
Guarding Against Electrostatic Damage, publication 8000-
4.5.2 Provides practices for guarding against Electrostatic
damage (ESD)
Product Certifications website, http://
www.rockwellautomation.com/global/certification/
overview.page
Provides declarations of conformity, certificates, and
other certification details.
Resource Description

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 13
Chapter 1
Selection Considerations
Before proceeding with detailed migration guidelines, see Table 1 on page 7 to
verify that you can migrate your PowerFlex 700AFE bus supply.
You must consider the hardware and control differences between the
PowerFlex 700AFE and PowerFlex 755TM bus supplies. This chapter
describes some of the primary differences. Additional chapters will provide in-
depth comparisons.
A common DC bus drive system is a complex electrical and mechanical system
that can be composed of many different power devices, such as DC input
common bus inverter, capacitor banks, bus conditioners, and common mode
filters. Because these drive systems are custom designed, it is important to
review the existing inverter and other equipment that will be connected to the
DC bus to confirm whether the equipment is compatible with the new
PowerFlex 755TM bus supply. Some devices are not compatible and must be
substituted, removed completely, or circuits modified for use with the
PowerFlex 755TM bus supply.
IMPORTANT Review Drives in Common Bus Configurations with PowerFlex 755TM Bus
Supplies application technique, publication DRIVES-AT005, to confirm that
the existing DC bus system and connected DC bus equipment iscompatible
with the PowerFlex 755TM bus supply converter.

14 Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Chapter 1 Selection Considerations
About the PowerFlex 700AFE
Bus Supply
The PowerFlex 700AFE, catalog code 20Y…, is available in two different power
rating frame sizes (frames 10 and 13) and three different packaging methods:
• IP00 open
• IP21 Rittal
• IP20 2500 Motor Control Centers (MCCs)
Custom enclosures and hardware configurations using Bulletin 2100 MCC
enclosures were created by Rockwell Automation drive systems and many
system integrators. Because of the many variations that are possible with IP00
open type equipment, this document does not cover custom engineered AFE
migrations. Contact an Authorized Rockwell Automation Distributor
specialist, Solution Partner, Recognized System Integrator, or a Rockwell
Automation account manager to discuss engineered solutions for these AFE
migrations.
A list of Solution Partners and Recognized System Integrators is located at:
http://www.software.rockwell.com/corporate/sp/
RASISearchResults.cfm?Programlevel=SP.
It was possible to parallel individual converters to increase the total available
DC bus power rating.
• The IP21 Rittal enclosed AFE can have up to six units of either frame
size paralleled.
• The IP20 2500 MCC could have two units of the same frame size
paralleled. Paralleling rules are in place, due to the ampere rating of the
DC bus bars available for the enclosures indicated.
When paralleled, the individual converters operate independently with 5%
droop, so a master/slave architecture was not required. Paralleling required
derating the AFE DC current and power output to 95% of published ratings.

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 15
Selection Considerations Chapter 1
PowerFlex 700AFE Catalog Number Explanation
The catalog current ‘Code’ numbers are related to the PowerFlex 700AFE AC
input current, NOT the DC output current. The ‘kW’ and ‘Hp’ columns in the
catalog structure tables are the DC output ratings.
Position
1…345…78 9101112 13 141516
20Y D 460 A 0 A N N A N A 0
abcdefghi jkl
a
Drive
Code Type
20Y PowerFlex 700AFE
b
Voltage Rating
Code Input Voltage Phase
D 400/480V AC 3
F 600/690V AC 3
c1
400/480V Input
Code Input
Amps
ND (HD)
kW at
400V
ND (HD)
Hp at
480V
ND (HD)
Frame
Size
460 460
(385)
309
(258)
497
(416) 10
1K3 1300
(1150) 873 (772) 1404 (1242) 13
c2
600/690V Input
Code Input
Amps
ND (HD)
Hp at
600V
ND (HD)
kW at
690V
ND (HD)
Frame
Size
325 325
(240)
439
(324)
376
(278) 10
1K0 1030(1)
(1) There is no heavy-duty rating for frame 13, 600/690V.
1390(1) 1193(1) 13
d
Enclosure
Code Type Conformal
Coating
A(1)
(1) Includes AFE power module, LCL filter, control assembly,
motor-controlled circuit breaker, and precharge circuit in
a Rittal enclosure.
IP21 Rittal Enclosure,
NEMA/UL Type 1 Yes
N(2)
(2) Restricted to SSB. Includes AFE power module, LCL filter,
and control assembly. Excludes circuit breaker or
precharge circuit.
IP00, open-chassis Yes
P(3)
(3) Includes AFE power module, LCL filter, control assembly,
Incoming circuit breaker, and precharge circuit in 2500
MCC Style enclosure. Frame 10 has 1250 A DC bus and
frame 13 has 3000 A DC bus.
IP20, NEMA/ULType 1
2500 MCCStyle enclosure
with power bus,
800 mm (31.5 in.) deep,
standard cabinet color
(RAL7032)
Yes
W(3)
IP20, NEMA/ULType 1
2500 MCCStyle enclosure
with power bus,
800 mm (31.5 in.) deep,
CenterLine 2100 gray
(ASA49)
Yes
e
HIM
Code Operator Interface Mount
0 No HIM AFE
f
Documentation
Code Documents Ship Carton
AUserManual Yes
g
Brake
Code With Brake IGBT
NNo
h
Brake Resistor
Code With Resistor
NNo
i
Equipment Type
Code Description
A AFE with power line filter
j
Comm Slot
Code Communication Option
NNone
k
I/O Option
Code Type I/O Volts
A(1)
(1) A 120V AC I/O option is not available.
Standard, with outputs 24V DC
l
Feedback
Code Type Installed On
0None —

16 Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Chapter 1 Selection Considerations
About the PowerFlex 755TM
Bus Supply
The PowerFlex 755TM bus supply, catalog code 20J…, is available in five
different power rating frame sizes (frames 8, 9, 10, 11, and 12) and three
different packaging methods:
• IP00 open
• IP21 Rittal
• IP54 Rittal
Paralleling of PowerFlex 755TM bus supplies is not supported. The PowerFlex
755TM bus supply is a fully regenerative, low harmonic active front end
converter that can easily be integrated with PowerFlex 750-Series and
PowerFlex 755TM IP20/IP54 enclosed common bus inverters. The enclosure
design and power/control bus bar systems in the PowerFlex 755TM bus supply
are mechanically and electrically compatible with similarly enclosed PowerFlex
750-Series and PowerFlex 755TM DC input common bus inverters.
IMPORTANT PowerFlex 755TM enclosures and bus systems are not directly compatible
with any existing PowerFlex 700AFE enclosures and connected inverter
enclosures. In almost all cases, it is necessary to employ a transition cabinet
between the existing drive enclosures and the new PowerFlex 755TM bus
supply enclosure.Transition cells are expected to be available from Rockwell
Automation at a later date.

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 17
Selection Considerations Chapter 1
PowerFlex 755T Product Catalog Number Explanation
a
b
c
d
e
f1
f3
f2
f4
Drive
Code Type Frames
20G
PowerFlex 755TL Drives 8…10
PowerFlex 755TR Drives
PowerFlex 755TM Common Bus Inverters 8…12
20J PowerFlex 755TM Bus Supplies 8…12
Cooling Type
Code Description Frames
1 Forced Air 8…12
Input
Type
Code Description Frames
D Common Bus with DC Precharge 8…12
E Common Bus without DC Precharge 8…12
F Regenerative and Low Harmonic AFE (1)
(1) Applies to PowerFlex 755TR drives and 755TM bus supplies.
8…12
G Low Harmonic AFE (2)
(2) Applies to PowerFlex 755TL drives.
8…10
Enclosure
Code Description Frames
3 IP21, UL Type 1; Floor Mount 8…12
4 IP54, UL Type 12; Floor Mount 8…12
Voltage Rating
Code Voltage
C 400V AC; 3 PH
D 480V AC; 3 PH
E 600V AC; 3 PH
F 690V AC; 3 PH
PowerFlex 755 ND Rating
400V, 50 Hz Input
Code Amps kW Frame
302 302 160
8
367 367 200
460 460 250
540 540 315
585 585 315
650 650 355
750 750 400
770 770 400
920 920 500
9
1K0 1040 560
1K1 1112 630
1K2 1175 710
1K4 1465 800
1K6 1590 850
101K7 1715 1000
2K1 2156 1250
2K8 2849 1650 11
3K5 3542 2000 12
PowerFlex 755 ND Rating
600V, 60 Hz Input
Code Amps Hp Frame
242 242 250
8
295 295 300
355 355 350
395 395 400
435 435 450
545 545 550
595 580 600
9
690 690 700
760 760 800
825 825 900
980 980 1000
1K1 1045 1100
101K2 1220 1250
1K5 1430 1500
2K0 1946 2000 11
2K4 2420 2500 12
PowerFlex 755 ND Rating
480V, 60 Hz Input
Code Amps Hp Frame
302 302 250
8
361 361 300
430 430 350
505 505 400
545 545 450
617 617 500
710 710 600
740 740 650
800 800 700
9
960 960 800
1K0 1045 900
1K1 1135 1000
1K3 1365 1100
1K4 1420 1250
101K6 1655 1500
2K0 2072 1800
2K6 2738 2400 11
3K4 3404 3000 12
PowerFlex 755 ND Rating
690V, 50 Hz Input
Code Amps kW Frame
215 215 200
8
265 265 250
330 330 315
370 370 355
415 415 400
505 505 500
565 565 560
9
650 650 630
735 735 710
820 820 800
920 920 900
1K0 1030 1000
101K1 1150 1100
1K4 1419 1400
1K8 1865 1800 11
2K3 2318 2300 12
1…3 4 5 6 7 8…10 11 12 13 14 15 16 17 18
20G
1 G 3 D 740 L N A N N N N N -C0-P15…
abcde ghif1…f4
Control and PowerOptionsPositions14…18 are not used.

18 Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Chapter 1 Selection Considerations
f5
f7
f6
f8
PowerFlex 755TM Bus Supplies ND Rating
400V, 50 Hz Input
Code Amps kW Frame
302 324 188
8
367 394 228
460 494 286
540 579 336
585 628 364
650 698 405
750 805 467
770 826 479
920 987 572
9
1K0 1116 647
1K1 1193 692
1K2 1261 731
1K4 1570 910
1K6 1697 984
101K7 1840 1067
2K1 2314 1342
2K8 3057 1772 11
3K5 3801 2204 12
PowerFlex 755TM Bus Supplies ND Rating
600V, 60 Hz Input
Code Amps kW Frame
242 249 217
8
295 303 263
355 365 317
395 406 353
435 447 389
545 560 487
595 596 518
9
690 710 617
760 782 680
825 848 737
980 1008 877
1K1 1075 935
101K2 1255 1091
1K5 1471 1279
2K0 2001 1740 11
2K4 2489 2164 12
PowerFlex 755TM Bus Supplies ND Rating
480V, 60 Hz Input
Code Amps kW Frame
302 311 216
8
361 371 258
430 442 307
505 519 361
545 560 390
617 635 442
710 730 508
740 761 529
800 823 573
9
960 987 687
1K0 1075 748
1K1 1167 812
1K3 1404 977
1K4 1460 1016
101K6 1702 1184
2K0 2131 1483
2K6 2816 1959 11
3K4 3501 2436 12
PowerFlex 755TM Bus Supplies ND Rating
690V, 50 Hz Input
Code Amps kW Frame
215 221 221
8
265 272 272
330 339 339
370 380 380
415 426 426
505 518 518
565 580 580
9
650 667 667
735 754 754
820 842 842
920 944 944
1K0 1057 1057
101K1 1180 1180
1K4 1456 1456
1K8 1914 1914 11
2K3 2379 2379 12
1…3 4 5 6 7 8…10 11 12 13 14 15 16 17 18
20J
1 F 3 C 1K6 L N A N N N N N -C1-P16…
abcde ghif5…f8
Control and PowerOptionsPositions 14…18 are notused.

Rockwell Automation Publication 750-RM003A-EN-P - April 2018 19
Selection Considerations Chapter 1
f9
f11
f10
f12
g
h
i
20GControl Options Selection
20JControlOptionsSelection
20GPowerOptionsSelection
20J PowerOptions Selection
PowerFlex 755TM Common Bus Inverter ND Rating
400V, 50 Hz Input
Code Amps kW Frame
302 302 160
8
367 367 200
460 460 250
540 540 315
585 585 315
650 650 355
750 750 400
770 770 400
920 920 500
9
1K0 1040 560
1K1 1112 630
1K2 1175 710
1K4 1465 800
1K6 1590 850
101K7 1715 1000
2K1 2156 1250
2K8 2849 1650 11
3K5 3542 2000 12
PowerFlex 755TM Common Bus Inverter ND Rating
600V, 60 Hz Input
Code Amps Hp Frame
242 242 250
8
295 295 300
355 355 350
395 395 400
435 435 450
545 545 550
595 580 600
9
690 690 700
760 760 800
825 825 900
980 980 1000
1K1 1045 1100
101K2 1220 1250
1K5 1430 1500
2K0 1946 2000 11
2K4 2420 2500 12
PowerFlex 755TM Common Bus Inverter ND Rating
480V, 60 Hz Input
Code Amps Hp Frame
302 302 250
8
361 361 300
430 430 350
505 505 400
545 545 450
617 617 500
710 710 600
740 740 650
800 800 700
9
960 960 800
1K0 1045 900
1K1 1135 1000
1K3 1365 1100
1K4 1420 1250
101K6 1655 1500
2K0 2072 1800
2K6 2738 2400 11
3K4 3404 3000 12
PowerFlex 755TM Common Bus Inverter ND Rating
690V, 50 Hz Input
Code Amps kW Frame
215 215 200
8
265 265 250
330 330 315
370 370 355
415 415 400
505 505 500
565 565 560
9
650 650 630
735 735 710
820 820 800
920 920 900
1K0 1030 1000
101K1 1150 1100
1K4 1419 1400
1K8 1865 1800 11
2K3 2318 2300 12
Filtering and CM Cap Configuration
Code EMC Filtering PE-A (1)
(1) Settingdoesnot apply toproducttype20Gwith inputtypes
D and E. PE-A jumpers are removed when bus conditioner
for marine applications (-P51) is selected.
PE-B ReflectedWave
Filtering
JYes
Installed Removed No
KYes
Installed Removed Yes
LNo
Installed Removed No
MNo
Installed Removed Yes
DynamicBraking(1)
(1) Not available on Frames 8…12, specify Code ‘N’.
Code Internal Resistor Internal Transistor
NNo No
Door-mounted HIM (Frames 8…10)
Code Operator
Interface and Control
ANo Door-mounted
HIM
with TotalFORCE Control
DEnhanced LCD, Full Numeric, IP66, NEMA Type
4X/12 with
TotalFORCE Control
Code Option Frames InputType
C0 Torque Accuracy Module 8…12 D, E, F, G
C11 Single Pod (with Control Bay) (1)
(1) When code ‘D’ is selected in position 13, code C11 includes
one door-mounted HIM and code C12 includes two door-
mounted HIMs.
8…12 D, E
C12 Dual Pod (with Control Bay) (1) 8…12 D, E
Code Option Frames InputType
C1 Control Transformer
(Internal 240V) (1)
(1) This option only applies to 755TM regenerative and low
harmonic bus supplies. If this option is not selected, a 240V
AC, single-phase, neutral grounded external power source
must be supplied by the customer.
8…12 F
Code Option Frames InputType
P15 Top Cable Exit w/wiring bay 8…12 D, E, F, G
P16 Top Cable Entry w/wiring bay 10…12 F, G
P17 Top Cable Entry no wiring bay 8… 9 F, G
P46 System DC Bus (4700 Amp) 8…10 D, E
P50 DC Bus Conditioner 8…12 F, G
P51 DC Bus Conditioner – Marine
Applications 8…12 F, G
Code Option Frames InputType
P16 Top Cable Entry w/wiring bay 10…12 F
P17 Top Cable Entry no wiring bay 8… 9 F
P46 System DC Bus (4700 Amp) 8…10 F
P50 DC Bus Conditioner 8…12 F
P51 DC Bus Conditioner – Marine
Applications 8…12 F
1…3 4 5 6 7 8…10 11 12 13 14 15 16 17 18
20G
1 D 3 F 2K3 M N D N N N N N -C0-C11-P15…
abcde ghif9…f12
Control and Power OptionsPositions 14…18 are not used.

20 Rockwell Automation Publication 750-RM003A-EN-P - April 2018
Chapter 1 Selection Considerations
Power and Control Bus Bar Ratings
DC power and control circuit bus bars may not be available, standard, or
optional for the PowerFlex 700AFE or PowerFlex 755TM bus supply. See
Table 2 to identify the existence and rating of bus bars.
The DC power bus bars and control power bus bars within the IP21/IP54
enclosed PowerFlex 755TM bus supplies are not mechanically or electrically
compatible with the bus bars in the IP21 Rittal or IP20 2500 MCC enclosed
PowerFlex 700AFE bus supplies. A transition enclosure may be required if the
new bus supply must interface electrically and mechanically with existing
common bus inverter power and control bus bars. Contact an authorized
Rockwell Automation Distributor specialist, Solution Partner, Recognized
System Integrator, or Rockwell Automation account manager to discuss
engineered solutions for these AFE migrations.
Table 2 - Power and Control Bus Bar Rating Comparison
Description PowerFlex 700AFE Bus Supply PowerFlex 755TM Bus Supply
DC Power Bus Bars • IP21 Rittal, enclosure code (A);
not applicable
• IP20 2500 MCC, enclosure code
(W); standard CENTERLINE™
DC bus,frame 10, 1250 A DC
frame 13, 3000 A DC
(s) frames 8…10; 3000 A DC
(s) frames 11…12; 4700 A DC
(o) frames 8…10; 4700 A DC,
specify power optioncode (-P46)
Control Power Bus Bars — (s) Primary control 240V AC, 1 PH, 100 A
(s) Auxiliary 24V DC, 100 A
(s) User 120/240V AC, 1 PH, 100 A
IMPORTANT PowerFlex 755TM common bus inverters that are used with the PowerFlex
755TM bus supply must have the sameDC bus bar rating as thebus supply.
PowerFlex 755TM 3000 A and 4700 A bus bars are not compatible with each
other. If any4700 A bus bars are used, then frames 8…10 drives and bus
suppliesmust havethe 4700A DCbusoption (-P46)installed.See the Drives
in Common Bus Configurations with PowerFlex 755TM Bus Supplies
application techniques, publication DRIVES-AT005, for detailed information
regarding PowerFlex 755TM DC bus bar compatibility.