Allen + Roth A102006002 User manual

ITEM #xxxxxx
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Friday.
PH18720
ATTACH YOUR RECEIPT HERE
GAZEBO
MODEL # A102006002
Français p. 20
1
TM

2
PACKAGE CONTENTS
PART
A
B
C
D1
D2
E
4
Post
Base cover
Base
Beam 1
Beam 2
Beam Connector
Inner Cover Plate
Arc Support Bar
DESCRIPTION QUANTITY
F
G
Netting pipe
H
I
PART
1
1
4
4
4
4
Small Roof Connector
Top Cover
Hook
Small Roof Sloping Beam Cover Plate
Small Roof Panel
Roof Panel 1
Roof Panel 2
Big Roof Sloping Beam Cover Plate
DESCRIPTION QUANTITY
O
P
Q
R
S
T1
T2
T3
T4
T6
T5
1
J
K
Big Roof Frame
Big Roof Sloping Beam
Big Roof Middle Beam
LBig Roof Small Beam
U
MSmall Roof Sloping Beam 4
VRoof Press Panel
4
4
4
4
4
8
4
4
4
4
4
4
8
8
4
4
4
8
Roof Panel 3
Roof Panel 4
Roof Panel 5
Roof Panel 6

3
HARDWARE CONTENTS
M6 X 15 mm Bolt
Qty. 176 + 9 spare
AA CC
DD
BB
EE GG
Z1
M6 X 40 mm Bolt
Qty. 32 + 2 spare
M6 X 45 mm Bolt
Qty. 1 + 1 spare
M6 X 55 mm Bolt
Qty. 8 + 1 spare
M6 Flat washer
Qty. 221 + 12 spare
Φ8X180 mm Stake
Qty.8
M6 Wrench
Qty. 2
HH
M6 X 30 mm Bolt
Qty. 4 + 1 spare

SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble or
install the product.
• Do not install the gazebo adjacent to trees or a sloped roof. Snow and ice may
slide onto the gazebo and cause it to collapse.
• Do not hang any weights on the roof frame.
• Keep all flame and heat sources away from the tent fabric. This tent is made
with fabric that meets CPAI-84 specifications for flame resistance. It is not fire
proof. The fabric will burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may render the
flame-resistant properties ineffective.
• Keep all children and pets away from assembly area. Children and pets should
be supervised while gazebo is being assembled.
• The assembled gazebo should be located at least 6 feet from any obstruction
such as fence, garage, house, overhanging branches, laundry lines or electrical
wires.
• Some parts may contain sharp edges. Wear protective gloves if necessary during
assembly.
• This unit is heavy. Do not assemble this item alone. Make sure there is sufficient
manpower for safe assembly or moving the gazebo.
• Check all nuts and bolts periodically for tightness and when required, tighten
them again.
• While this gazebo is manufactured to withstand winds through only the supplied
ground stakes, in areas subject to frequent severe weather, securing the gazebo
to a deck, concrete patio or footings should be considered.
• Do not use or enter the gazebo during harsh weather (e.g. thunderstorms,
high winds, hail, heavy snow, etc). In these conditions, it might tip over and
could cause serious injury to bystanders. Any damage or injury caused by
which is not covered by the warranty.
• Do not use or enter the gazebo if there exists any of the following or similar
conditions:
1. Visible movement of support members, roofing panels or sagging roofline.
2. Creaks or audible noise from the gazebo.
3. Cracks, fractures or malformation of support members or roof panels.
4. Damaged or missing fasteners.
• Do not use a ladder leaning against the gazebo or climb onto the roof.
WARNING
4
CAUTION

• If the gazebo will not be used for a long period of time (e.g. during winter time),
disassemble and store it in a clean, dry environment.
• This product is for domestic, outdoor use (i.e. decorative and sunshade
purposes only).
• Install the gazebo on level ground. Stakes are provided to secure the gazebo
to the ground. Do not assemble the gazebo on sandy, muddy or loose soil,
as stakes do not have enough anchorage in these types of soil. If you wish to
secure the gazebo to a wood deck or concrete surface, use anchors suited to
these surfaces (anchors not included).
• Always ensure the roof canvas is tensioned so as to avoid water accumulation
on the roof.
• Remove accumulated water on the roof immediately, or disassemble the gazebo
in order to avoid damages.
• Do not remove snow from inside the gazebo by pushing on the fabric. Snow
must be cleared off regularly during snowy days. Remove the snow at the top
when it is thicker than 4 inches. In order to avoid damages, use a plastic snow
rake to remove excessive snow and ice buildup from roof and keep away from
falling debris.
• Always disassemble the gazebo before experiencing heavy wind conditions, as
it is semi-permanent construction and not designed to withstand harsh weather,
including high wind, rain and snow.
• Please check your state and local regulations prior to purchasing. Some
jurisdictions may require permits for installation and use. Some special
procedures may be valid in your area.
• Center hook’s maximum weight: 26 lbs.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is missing
or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 120-150 minutes
Tools Required for Assembly (included): Wrench .
Tools Required for Assembly (not included): hammer, and 2 ladders.
5
CAUTION

6
ASSEMBLY INSTRUCTIONS
1. Insert the Base Cover (B) to the Post (A),
Then attach Base (C) to the Post (A) with
Bolts (AA) and Flat Washer (EE). Tighten
with Allen Key (Z1).
Hardware Used
x 8
x 8
M6 x 15 mm Bolt
x 1
M6 Flat washer
Z1 M6 Wrench

7
ASSEMBLY INSTRUCTIONS
2.Insert Beam Connector (E) to the Beam 2
with Bolts (AA) and Flat Washer (EE).
Then insert Beam 1 (D1) to the Beam
Connector (E) with Bolts (AA) and Flat
Washer (EE).Tighten with Allen Key (Z1).
Hardware Used
x 16
x 16
3.Attach Beam 2 ( D2) and Beam 1 (D1) to
the Post (A) with Bolts (AA) and Flat
Washer (EE). Tighten with Allen Key (Z1).
Hardware Used
x 16
x 16
4.Attach Arc Support Bar (G) to the Beam
(D1/D2) and Post ( A ) with Bolts (BB), Flat
Washer (EE) and Plastic Cap (FF). Tighten
with Allen Key (Z1).
Hardware Used
x 32
M6 x 40 mm Bolt
x 1
x 1
M6 x 15 mm Bolt
M6 Flat washer
Z1 M6 Wrench
M6 x 15 mm Bolt
M6 Flat washer
Z1 M6 Wrench
x 32
x 1
M6 Flat washer
Z1 M6 Wrench

8
ASSEMBLY INSTRUCTIONS
5.Attach the Netting Pipe (H) to the Beam 2
(D2) and Beam 1 (D1) with Bolts (AA),
Flat Washer (EE) and Plastic Cap (FF).
Tighten with Allen Key (Z1).
Hardware Used
x 16
x 16
M6 x 15 mm Bolt
M6 Flat washer
6.Assemble the Big Roof Frame (I) with
Bolts (AA) and Flat Washer (EE).Tighten
with Allen Key (Z1).
Hardware Used
x 4
M6 x 15 mm Bolt
x 1
Z1 M6 Wrench
x 4
M6 Flat washer
x 1
Z1 M6 Wrench

9
ASSEMBLY INSTRUCTIONS
7.Attach the assembled big roof frame (I)
to the Big Roof Sloping Beam (J) with
Bolts (AA) and Flat Washer .Tighten with
Allen Key (Z1).
Hardware Used
8.Attach the Big Roof Sloping Beam (J) to
the Post (A) with Bolts (AA) and Flat
Washer (EE). Tighten with Allen Key (Z1).
Hardware Used
9.Attach the Inner Cover Plate (F) to the
Post (A) with Bolts (AA), Flat Washer
(EE) and Plastic Cap (FF).Tighten with
Allen Key (Z1).
Hardware Used
x 8
x 8
M6 x 15 mm Bolt
M6 Flat washer
x 1
Z1 M6 Wrench
x 8
x 8
M6 x 15 mm Bolt
M6 Flat washer
x 1
Z1 M6 Wrench
x 8
x 8
M6 x 15 mm Bolt
M6 Flat washer
x 1
Z1 M6 Wrench

10
ASSEMBLY INSTRUCTIONS
10.Attach Big Roof Middle Beam (K) to
the Big Roof Frame (I) with Bolts (AA)
and Flat Washer (EE). Tighten with
Allen Key (Z1).
Hardware Used
11.Attach Big Roof Middle Beam (K) to the
assembled Beam (D1/D2) with Bolts
(AA) and Flat Washer (EE). Tighten with
Allen Key (Z1).
Hardware Used
12.Attach Small Roof Sloping Beam (M) to
the Small Roof Connector (O) with Bolts
(AA) and Flat Washer (EE). Tighten with
Allen Key (Z1).
Hardware Used
x 8
x 8
M6 x 15 mm Bolt
M6 Flat washer
x 1
Z1 M6 Wrench
x 4
x 4
M6 x 15 mm Bolt
M6 Flat washer
x 1
Z1 M6 Wrench
x 8
x 8
M6 x 15 mm Bolt
M6 Flat washer
x 1
Z1 M6 Wrench