Alliance Laundry Systems 504522R3 Owner's manual

Installation and Operation
Dryer
Metered and Nonmetered
Electric and Gas Models
Part No. 504522R3
July 1998
NOTA: El manual en español aparece después del manual en inglés.
D334IE1D

504522 1
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If the dryer changes ownership, be
sure this manual accompanies the dryer.)
IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be
followed if the dryer user smells gas. The gas utility instructions plus the SAFETY and
WARNING note directly above must be posted in a prominent location near the dryer for
customer use.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch; do not use any phone in your building.
– Clear the room, building or area of all occupants.
– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
– If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or
the gas supplier. W052
FOR YOUR SAFETY, the information in this manual must be followed to minimize the
risk of fire or explosion or to prevent property damage, personal injury or death.W033
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.

2504522
Replacement Parts . . .
If replacement parts are required, contact the source
where you purchased your dryer, or contact Alliance Laundry Systems LLC Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
Phone:
[phone]
for the name and address of the nearest authorized parts
distributor.
Table of
Contents
Replacement Parts ............................................................................... 2
Important Safety Instructions.............................................................. 3
Roughing In Dimensions ..................................................................... 5
Meter Case............................................................................................. 7
Timer Cams ........................................................................................... 7
Dryer Slide Extension .......................................................................... 8
Before You Start ................................................................................... 9
Installing the Dryer
Step 1 – Position and Level the Dryer ........................................... 10
Step 2 – Connect Dryer Exhaust System........................................ 10
Step 3 – Connect Gas Supply Pipe.................................................11
Step 4 – Connect Electrical Plug.................................................... 12
Step 5 – Wipe Out Inside of Dryer ................................................. 13
Step 6 – Plug in the Dryer .............................................................. 13
Step 7 – Check Installation.............................................................13
Heat Source Check ............................................................................. 14
Reversing Door Procedure ................................................................ 15
Manufactured (Mobile) Home Installation ...................................... 16
Electrical Requirements (Electric Dryers) ....................................... 17
Electrical Connection ......................................................................... 18
Three-Wire Power Cord ................................................................. 18
Four-Wire Power Cord .................................................................. 20
Electrical Requirements (Gas Dryers) ............................................. 22
Gas Requirements ............................................................................. 24
Location Requirements ..................................................................... 25
Dryer Exhaust Requirements ........................................................... 26
Multi-Dryer Installation Exhuast Requirements ............................. 29
Lint Filter............................................................................................. 32
Motor Overload Protector.................................................................. 32
User-Maintenance Instructions ......................................................... 33
For Energy Conservation ................................................................... 33
Before You Call for Service ................................................................ 34
Additional Dryer Security.................................................................. 35
Operation Instructions For Electromechanical Dryers .................. 36
Operation Instructions for Electronic Control Dryers.................... 38
Information for Handy Reference .................................................... 41
Installer Check .................................................................... Back Cover
©Copyright 1998, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without
the written permission of the publisher.

504522 3
IMPORTANT SAFETY INSTRUCTIONS
(SAVE THESE INSTRUCTIONS)
1. Read all instructions before using the dryer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the dryer.
3. Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable
or explosive substances as they give off vapors
that could ignite or explode.
4. Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children. This is a safety
rule for all appliances.
5. Before the dryer is removed from service or
discarded, remove the door to the drying
compartment.
6. Do not reach into the dryer if the cylinder is
revolving.
7. Do not install or store the dryer where it will be
exposed to water and/or weather.
8. Do not tamper with the controls.
9. Do not repair or replace any part of the dryer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
10. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
11. To reduce the risk of fire, DO NOT DRY plastics
or articles containing foam rubber or similarly
textured rubberlike materials.
12. ALWAYS clean the lint filter after every load. A
layer of lint in the filter reduces drying efficiency
and prolongs drying time.
13. Keep area around the exhaust opening and
adjacent surrounding area free from the
accumulation of lint, dust and dirt.
14. The interior of the dryer and the exhaust duct
should be cleaned periodically by qualified
service personnel.
15. If not installed, operated and maintained in
accordance with the manufacturer’s instructions
or if there is damage to or mishandling of this
product’s components, use of this product could
expose you to substances in the fuel or from fuel
combustion which can cause death or serious
illness and which are known to the State of
California to cause cancer, birth defects or other
reproductive harm.
16. Dryer will not operate with the loading door
open. DO NOT by-pass the door safety switch by
permitting the dryer to operate with the door
open. The dryer will stop tumbling when the door
is opened. Do not use the dryer if it does not stop
tumbling when the door is opened or starts
tumbling without pressing the START
mechanism. Remove the dryer from use and call
the service person.
17. Do not put articles soiled with vegetable or
cooking oil in the dryer, as these oils may not be
removed during washing. Due to the remaining
oil, the fabric may catch on fire by itself.
18. To reduce the risk of fire, DO NOT put clothes
which have traces of any flammable substances
such as machine oil, flammable chemicals,
thinner, etc., or anything containing wax or
chemicals such as in mops and cleaning cloths, or
anything dry-cleaned at home with a dry-
cleaning solvent in the dryer.
19. Use the dryer only for its intended purpose,
drying clothes.
20. Always disconnect the electrical power to the
dryer before attempting service. Disconnect the
power cord by grasping the plug, not the cord.
21. Replace worn power cords and/or loose plugs.
22. Install this dryer according to the
INSTALLATION INSTRUCTIONS. All
connections for electrical power, grounding and
gas supply must comply with local codes and be
made by licensed personnel when required. Do
not do it yourself unless you know how!
23. Remove laundry immediately after the dryer
stops.
To reduce the risk of fire, electric shock, or
injury to persons when using your dryer,
follow these basic precautions:
W034
WARNING

4504522
24. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of reach of children at all times
(preferably in a locked cabinet).
25. Do not tumble fiber glass curtains and draperies
unless the label says it can be done. If they are
dried, wipe out the cylinder with a damp cloth to
remove particles of fiber glass.
26. ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
27. Never operate the dryer with any guards and/or
panels removed.
28. DO NOT operate the dryer with missing or
broken parts.
29. DO NOT by-pass any safety devices.
30. Failure to install, maintain, and/or operate this
machine according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
IMPORTANT: Solvent vapors from dry-cleaning
machines create acids when drawn through the heater
of the drying unit. These acids are corrosive to the
dryer as well as to the laundry load being dried. Be
sure make-up air is free of solvent vapors.
IMPORTANT: Have your dryer installed properly.
Don’t do it yourself unless you know how!
NOTE: The WARNING and IMPORTANT
SAFETY INSTRUCTIONS appearing in this manual
are not meant to cover all possible conditions and
situations that may occur. Common sense, caution
and care must be exercised when installing,
maintaining, or operating the dryer.
Always contact your dealer, distributor, service agent or
the manufacturer about any problems or conditions you
do not understand.

504522 5
Roughing In Dimensions . . .
(Metered Models)
NOTE: Side, rear and bottom exhaust openings are
four inch (10.2 cm) ducting. Gas models cannot be
vented out left side of cabinet because of burner
housing.
IMPORTANT: The dryer should have sufficient
clearance around it for needed ventilation and for the
ease of installation and servicing. For maximum
drying performance, we recommend that more
clearance be allowed around the dryer than the
clearances that are listed throughout this manual.
ELECTRIC MODELS
D329IE3A
23.5"
(59.7 cm)
*36" (91.4 cm)
*43.2" (109.7 cm)
28"
(71.1 cm)
.4"
(1.0 cm) 26.9"
(68.3 cm)
7.7"
(19.6 cm)
4.0"
(10.2 cm)
15.4"
(39.1 cm)
4.0"
(10.2 cm)
* WITH LEVELING LEGS TURNED INTO BASE.
GAS MODELS
D330IE3A
23.5"
(59.7 cm)
*36" (91.4 cm)
*43.2" (109.7 cm)
28"
(71.1 cm)
.4"
(1.0 cm) 26.9"
(68.3 cm)
7.7"
(19.6 cm)
15.4"
(39.1 cm)
4.0"
(10.2 cm)
* WITH LEVELING LEGS TURNED INTO BASE.
2.8"
(7 cm)
2.3"
(6 cm)
4.0"
(10.2 cm)
3/8"
NPT GAS
CONNECTION

6504522
(Nonmetered Models)
NOTE: Side, rear and bottom exhaust openings are
four inch (10.2 cm) ducting. Gas models cannot be
vented out left side of cabinet because of burner
housing.
IMPORTANT: The dryer should have sufficient
clearance around it for needed ventilation and for the
ease of installation and servicing. For maximum
drying performance, we recommend that more
clearance be allowed around the dryer than the
clearances that are listed throughout this manual.
ELECTRIC MODELS
D331IE3A
23.5"
(59.7 cm)
*36" (91.4 cm)
*43.2" (109.7 cm)
28"
(71.1 cm)
.4"
(1.0 cm) 26.9"
(68.3 cm)
7.7"
(19.6 cm)
4.0"
(10.2 cm)
* WITH LEVELING LEGS TURNED INTO BASE.
15.4"
(39.1 cm)
4.0"
(10.2 cm)
GAS MODELS
D332IE3A
23.5"
(59.7 cm)
*36" (91.4 cm)
*43.2" (109.7 cm)
28"
(71.1 cm)
.4"
(1.0 cm) 26.9"
(68.3 cm)
7.7"
(19.6 cm)
15.4"
(39.1 cm)
4.0"
(10.2 cm)
* WITH LEVELING LEGS TURNED INTO BASE.
3/8"
NPT GAS
CONNECTION
2.8"
(7 cm)
2.3"
(6 cm)
4.0"
(10.2 cm)

504522 7
Meter Case . . .
(Metered Models)
The factory mounted coin meter case does not include the
service door lock, coin drawer, coin drawer lock and
keys. These parts must be ordered (at extra cost)
according to the purchaser’s requirements direct from the
manufacturer of your choice.
NOTE: You have the option of using a screw type lock
or a 1/4 turn lock on the meter case service door. If
you choose to use a screw lock, then the special
bracket (located inside the meter case) must be used.
DO NOT use the special bracket if a 1/4 turn lock is
used.
Coin Drawer Security —for additional security, drill
out the two pilot holes on each front side of the meter case
to 1/4 or 5/16 inch (6.4 or 8.0 mm) holes and install a
bicycle lock through these holes.
Timer Cams . . .
(Metered Models)
The dryer timer is factory equipped with a 45 minute
timing cam. If this drying time is not suitable to your installation, the following cams can be found in the envelope located in the cylinder:
Electric Dryers Gas Dryers
1-53242 Cams (30 Minutes) 1-53242 Cams (30 Minutes)
1-53240 Cams (60 Minutes)
A 60 minute timing cam, Part No. 53240, is available for gas
dryers as optional equipment at extra cost.

8504522
Dryer Slide Extension . . .
1. Assemble coin slide extension, No. 503733, to top
side of coin slide using two Phillips head screws and
lockwashers, No. 03950. Tighten firmly. See
illustration below.
2. Install slide extension modifier, No. 501796, as
follows:
NOTE: Dryers equipped with Greenwald coin slides
(except for Greenwald Comet Slide or Greenwald
Tokette Slide) do not require the use of the slide
extension modifier.
•ESD Coin Slide —Mount slide extension
modifier, No. 501796, to the underside of slide
extension, No. 503733. Align the hole in the slide
extension modifer with hole "A" in the slide
extension and install self-tapping screw, No.
501086. Tighten firmly. See illustration below.
•GREENWALD Comet Slide, GREENWALD
Tokette Slide or MONARCH Coin Slide —
Mount slide extension modifier, No. 501796, to the
underside of slide extension, No. 503733. Align the
hole in the slide extension modifier with hole "B"
in the slide extension and install self-tapping screw,
No. 501086. Tighten firmly. See illustration below.
3. Reinstall coin slide in dryer meter case.
4. CHECK DRYER OPERATION —Connect
electrical power to dryer. Place required number of
coins in coin slide. Push slide in, and observe through
service door opening in meter case. The slide
extension should be contacting the accumulator
actuator arm and moving back with slide travel.
When slide is pushed all the way in, slide is retracted.
Accumulator actuator arm should remain back until slide
extension is moved forward and contacts actuator arm
again, returning arm to starting position. See illustration
below.
5. After completing the dryer check, reinstall service
door on top of meter case.
NOTE: When reinstalling service door, front of door
must be inserted at about a 45°angle in order to
engage notched tabs with internal rib at top of meter
case.
To reduce the risk of electric shock, fire, explosion, serious injury or death:
•Disconnect electric power to the dryer(s) before servicing.
•Close gas shut-off valve to gas dryer(s) before servicing.
•Never start the dryer(s) with any guards/panels removed.
•Whenever ground wires are removed during servicing, these ground wires must be reconnected
to ensure that the dryer is properly grounded.
W001R1
WARNING
D019KE1C
COIN
SLIDE
03950
PHILLIPS
HEAD
SCREWS
AND
LOCKWASHERS
HOLE "B"
503733
SLIDE
EXTENSION
HOLE "A"
501796
SLIDE EXTENSION
MODIFIER
501086
SELF-TAPPING
SCREW
D044KE1A
ACCUMULATOR
ACTUATOR ARM SLIDE
EXTENSION
MODIFIER
SLIDE
EXTENSION
COIN
SLIDE